AMERICAN DJ Stinger Gobo — технические характеристики и особенности светового оборудования [14/14]

Содержание

• User instructions p.1
• Stinger gobo p.1
• Warning p.2
• Unpacking p.2
• Introduction p.2
• Customer support p.2
• Caution p.2
• Stop and read all laser safety data operation instructions and laser safety p.3
• Power supply p.4
• Dmx 512 p.4
• The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit always ensure that the unit is firmly fixed to avoid vibration and slip ping while operating always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit s weight also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture the equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp p.5
• Stinger gobo installation p.5
• Stinger gobo dmx set up p.5
• Special note line termination p.5
• Some manufactures use 5 pin xlr connectors for data transmission in place of 3 pin 5 pin xlr fixtures may be implemented in a 3 pin xlr dmx line when inserting stan dard 5 pin xlr connectors in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion p.5
• Pin xlr to 5 pin xlr conversion p.5
• Pin xlr dmx connectors p.5
• Pin 5 do not use p.5
• Pin 4 do not use p.5
• Notice p.5
• Not used p.5
• Ground shield p.5
• Data true signal p.5
• Data compliment signal p.5
• Conductor 5 pin xlr male in 3 pin xlr female out p.5
• When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior p.5
• Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior p.5
• Us version p.6
• Stinger gobo rear layout p.6
• Stinger gobo laser warning labels p.6
• Stinger gobo cad drawing p.6
• Europe version p.6
• This will let select your desired dmx channel mode p.7
• System menu when making adjustments press enter to confirm your setup then press and hold the menu button for at least 3 seconds to exit without making any adjust ments press the menu button the display will lock after 30 seconds press the menu button for 3 seconds to unlock p.7
• Show modes 0 6 factory programs p.7
• Show mode speed p.7
• Dmx address setting p.7
• This will let you set unit as a master or slave in a master slave configuration p.8
• This will activate strobing p.8
• This mode can be used as a precaution mode that in case the dmx signal is lost interrupted or power is lost the operating mode chosen in the setup is the running mode the fixture will go into when the dmx signal is lost you can also set this as the operating mode you would like the unit to return to when power is applied p.8
• Sound active mode p.8
• In this mode you can adjust the sound sensitiv ity p.8
• With this function you can have the led display turn off after 10 seconds p.8
• With this function you can display the running time of the unit p.9
• Use this function to display the software version of the unit p.9
• Universal dmx control p.9
• This function will run a self test program p.9
• This function will reverse the display 180º p.9
• This function will reset the unit p.9
• The display will show the software version p.9
• Sound active mode p.9
• Show mode p.9
• Press the menu button until rset is displayed press the enter button and the unit will reset itself p.9
• Uc ir airstream control p.10
• Master slave set up p.10
• Master slave operation p.10
• Fixture cleaning p.12
• Channel value function p.12
• Laser horizontal position 0 127 select horizontal position 128 255 horizontal move slow fast 12 laser vertical position 0 127 select vertical position 128 255 vertical move slow fast 13 laser path 0 255 select laser path 14 laser path speed 0 255 path speed slow fast p.12
• Stinger gobo warranty p.13
• Stinger gobo notes p.13
• Adj products llc www adj com stinger gobo instruction manual page 24 adj products llc www adj com stinger gobo instruction manual page 25 p.13
• Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice p.14
• Please note p.14
• Model stinger gobo p.14
• Auto sensing voltage this fixture contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source p.14
• Adj products llc 6122 s eastern ave los angeles ca 90040 usa tel 323 582 2650 fax 323 725 6100 web www adj com e mail info americandj com p.14
• A d j supply europe b v junostraat 2 6468 ew kerkrade the netherlands service adjgroup eu www adj com tel 31 45 546 85 00 fax 31 45 546 85 99 p.14

Похожие устройства

• 
  AMERICAN DJ Dotz TPAR System

  Руководство по эксплуатации
• 
  AMERICAN DJ Stinger Star

  Руководство по эксплуатации
• 
  AMERICAN DJ Zipper

  Руководство по эксплуатации
• 
  AMERICAN DJ Rotobeam 4

  Руководство по эксплуатации
• 
  AMERICAN DJ BOOM BOX FX3

  Руководство по эксплуатации
• 
  ADJ Hydro Beam X1

  Руководство по эксплуатации
• 
  Involight LDF100

  Руководство по эксплуатации
• 
  AMERICAN DJ Focus Spot ONE

  Руководство по эксплуатации
• 
  Involight LED PAR984W

  Руководство по эксплуатации
• 
  Antari M-7

  Руководство по эксплуатации
• 
  STAGG SLI KINGPAR22

  Руководство по эксплуатации
• 
  ADJ Par Z Move

  Руководство по эксплуатации

Узнайте о характеристиках и возможностях светового оборудования, включая мощность, размеры и режимы работы. Идеально для мероприятий и шоу.