![AMERICAN DJ Focus Spot ONE [15/18] Once you loosen the single screw you are able to swing the head back see instruction number 2 on the next page you will now be able to access the gobo wheel turn the wheel with your hand until you come across the gobo you would like to change](/img/pdf.png)
AMERICAN DJ Focus Spot ONE [15/18] Once you loosen the single screw you are able to swing the head back see instruction number 2 on the next page you will now be able to access the gobo wheel turn the wheel with your hand until you come across the gobo you would like to change
![AMERICAN DJ Focus Spot ONE [15/18] Once you loosen the single screw you are able to swing the head back see instruction number 2 on the next page you will now be able to access the gobo wheel turn the wheel with your hand until you come across the gobo you would like to change](/views2/2014198/page15/bgf.png)
ADJ Products, LLC - www.adj.com - Focus Spot One Instruction Manual Page 28
ADJ Products, LLC - www.adj.com - Focus Spot One Instruction Manual Page 29
The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
The Airstream IR (sold separately) remote transmitter plugs into
the headphone jack of your iOS phone or tablet. To control your IR
fixture you must raise the volume to the maximum on your iOS phone
or tablet and aim the transmitter at the fixture sensor and be no more
than 15 feet away. After you have purchased the Airstream IR trans-
mitters, the app is a free download from the app store for your iOS
phone or tablet. The app comes with 3 pages of control depending
on the fixture you are using. Please see below for IR functions. This
unit works with App page 1.
STAND BY - Pressing this button will blackout the fixture.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
FADE/GOBO - Press this button once to access gobo wheel. Use
the number buttons to find your desired gobo.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the out-
put intensity in Color mode.
STROBE - This button will activate the strobe effect. Press and hold
this button to activate strobing and release the button to stop strob-
ing.
COLOR - Press this button to access the color wheel. Use the num-
ber buttons to select your desired color. Adjust the output intensity
using the “DIMMER +” and “DIMMER -” buttons.
1-9 - In color mode and gobo mode, these buttons will allow you to
select a desired color or gobo. In show mode buttons 1-4 will let you
select your desired show.
SOUND ON & OFF - These buttons activate and deactivate the
sound active mode.
SHOW - This activates the show mode. Use buttons 1-4 to select
your desired show.
Focus Spot One Remote Operation
The gobo’s in this unit are interchangable. Please be very care-
ful when replacing the gobo.
Caution! Never open the unit when in use. Always disconnect
the main power before attempting to change the gobos.
1. To change a gobo, rotate the moving head so that the UV
lens is located on top. Unscrew the single middle screw. See
instruction number 1 on the next page.
2. Once you loosen the single screw you are able to swing the
head back. See instruction number 2 on the next page. You
will now be able to access the gobo wheel. Turn the wheel
with your hand until you come across the gobo you would
like to change.
3. To remove the gobo holder gently pull the gobo holder to-
wards the front of the unit and slide it up and out.
4. Gently and carefully remove the retainer ring. After the re-
tainer ring is removed, carefully remove the gobo.
5. Change the gobo and replace the retainer ring. Carefully slide
the gobo holder back into the housing slot.
6. Reassemble the unit.
Focus Spot One Changing the Gobo
Содержание
- User instructions p.1
- Focus spot one p.1
- Warning p.2
- Unpacking p.2
- Introduction p.2
- Customer support p.2
- Caution p.2
- Suspender screew p.4
- Mm 7 5 p.4
- Mm 14 7 p.4
- Power supply p.5
- Dmx 512 p.5
- Ground shield p.6
- Focus spot one dmx set up p.6
- Data true signal p.6
- Data compliment signal p.6
- Conductor 5 pin xlr male in 3 pin xlr female out p.6
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior p.6
- Your cables should be made with a male and female xlr connector on either end of the cable also remember that dmx cable must be daisy chained and cannot be split p.6
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior p.6
- Special note line termination p.6
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion p.6
- Pin xlr to 5 pin xlr conversion p.6
- Pin xlr dmx connectors p.6
- Pin 5 do not use p.6
- Pin 4 do not use p.6
- Notice p.6
- Not used p.6
- Focus spot one 15 channel mode p.7
- Channel value function p.7
- Gobo 1 gobo 2 gobo 3 p.8
- Focus spot one 17 channel mode p.8
- Focus spot one 15 channel mode p.8
- Channel value function p.8
- Gobo 4 gobo 5 gobo 6 p.8
- Gobo 4 gobo 5 gobo 6 p.9
- Gobo 1 gobo 2 gobo 3 p.9
- Focus spot one 17 channel mode p.9
- Channel value function p.9
- This will let you set unit as a master or slave in a master slave configuration p.10
- This will let you select your desired dmx channel mode p.10
- System menu when making adjustments press enter to confirm your setup then press and hold the menu button for at least 3 seconds to exit without making any adjust ments press the menu button the display will lock after 30 seconds press the menu button for 3 seconds to unlock p.10
- Slave mode p.10
- Set the dmx address p.10
- Dmx addres p.10
- Channel mod p.10
- In this mode you can select the dimmer curve p.11
- In this mode you can adjust the sound sensitivity of the sound active mode p.11
- In this mode the unit will run in sound active mode p.11
- Dimmer curv p.11
- This mode can be used as a precaution mode that in case the dmx signal is lost the operating mode chosen in the setup is the running mode the fixture will go into when the dmx signal is lost you can also set this as p.11
- The operating mode you would like the unit to return to when power is applied p.11
- Sound stat p.11
- Sound sens p.11
- Show modes 0 4 factory programs show mode can run with or without sound active mode active p.11
- Show mod p.11
- Pan inversion p.11
- Pan inver p.11
- Last stat p.11
- This function will restore all factory settings p.12
- Software versio p.12
- Pro default p.12
- Fixture temp p.12
- Fixture hour p.12
- Back ligh p.12
- Auto tes p.12
- With this function you can make the back light automatically turn off after one minute p.12
- With this function you can display the running time of the unit p.12
- With this function you can display the running temperature of the unit p.12
- Use this function to reset the motors p.12
- Tilt inversion p.12
- Tilt inver p.12
- This will display the firmware soft ware version p.12
- This function will run a self test program p.12
- Setting adjustment for the focus p.13
- Setting adjustment for the color wheel p.13
- Pan offse p.13
- Gobo offse p.13
- Focus offse p.13
- Color offse p.13
- Adjustment of the tilt home position p.13
- Adjustment of the pan home position p.13
- Tilt offse p.13
- Setting adjustment for the gobo wheel p.13
- Universal dmx control p.14
- Sound active mode p.14
- Show mode p.14
- Master slave operation p.14
- To remove the gobo holder gently pull the gobo holder to wards the front of the unit and slide it up and out p.15
- To change a gobo rotate the moving head so that the uv lens is located on top unscrew the single middle screw see instruction number 1 on the next page p.15
- The gobo s in this unit are interchangable please be very care ful when replacing the gobo caution never open the unit when in use always disconnect the main power before attempting to change the gobos p.15
- Reassemble the unit p.15
- Once you loosen the single screw you are able to swing the head back see instruction number 2 on the next page you will now be able to access the gobo wheel turn the wheel with your hand until you come across the gobo you would like to change p.15
- Gently and carefully remove the retainer ring after the re tainer ring is removed carefully remove the gobo 5 change the gobo and replace the retainer ring carefully slide the gobo holder back into the housing slot p.15
- Remove the lens 4 unscrew the 4 screws located on the other side p.16
- Focus spot one removing the head casing p.16
- Focus spot one photometric chart p.16
- Focus spot one dimmer curve chart p.16
- Unscrew the single screw 2 flip the top cover back p.16
- Trouble shooting listed below are a few common problems that you may encounter with solutions p.17
- No light output from the unit p.17
- Low frequencies bass should cause the unit to react to sound tapping on the microphone quiet or high pitched sounds may not activate the unit p.17
- Locate and remove the unit s powercon cord once the cord has been removed the fuse holder is located next to the power socket use a philips head screw driver unscrew the fuse holder remove the bad fuse and replace with a new one p.17
- Focus spot one warranty p.17
- Focus spot one trouble shooting p.17
- Focus spot one fuse replacement p.17
- Focus spot one cleaning p.17
- Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses and mirror should be carried out periodically to optimize light output cleaning frequency depends on the environ ment in which the fixture operates i e smoke fog residue dust dew in heavy club use we recommend cleaning on a monthly basis periodic cleaning will ensure longevity and crisp output 1 use normal glass cleaner and a soft cloth to wipe down the out side casing 2 use a brush to wipe down the cooling vents and fan grill 3 clean the external optics with glass cleaner and a soft cloth every 20 days 4 clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 always be sure to dry all parts completely before plugging the unit back in p.17
- Be sure the external fuse has not blown the fuse is located on the rear panel of the unit 2 be sure the fuse holder is completely and properly seated unit does not respond to sound p.17
- Adj products llc www adj com focus spot one instruction manual page 32 adj products llc www adj com focus spot one instruction manual page 33 p.17
- Please note p.18
- Model focus spot one p.18
- Auto sensing voltage p.18
- A d j supply europe b v junostraat 2 6468 ew kerkrade the netherlands service adjgroup eu www adj eu tel 31 45 546 85 00 fax 31 45 546 85 99 p.18
- This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source adj products llc 6122 s eastern ave los angeles ca 90040 usa tel 323 582 2650 fax 323 725 6100 web www adj com e mail info americandj com p.18
- Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice p.18
Похожие устройства
-
AMERICAN DJ Vizi QWash7Руководство по эксплуатации -
AMERICAN DJ Vizi Hex Wash7Руководство по эксплуатации -
Involight PROSPOT500SETРуководство по эксплуатации -
DIALIGHTING Mini Spot 50Руководство по эксплуатации -
DIALIGHTING MINI BEAM 150 MKIIРуководство по эксплуатации -
DIALIGHTING Profile BSW 400Руководство по эксплуатации -
DIALIGHTING WASH ZOOM 19x40Руководство по эксплуатации -
DIALIGHTING Wash Zoom 700Руководство по эксплуатации -
Involight MH78WРуководство по эксплуатации -
DIALIGHTING IW30-15 zoomРуководство по эксплуатации -
Involight MH255WРуководство по эксплуатации -
Involight MH575S OLDРуководство по эксплуатации