![AMERICAN DJ Focus Spot ONE — инструкция по эксплуатации для осветительного оборудования [5/18]](/img/pdf.png)
AMERICAN DJ Focus Spot ONE — инструкция по эксплуатации для осветительного оборудования [5/18]
Превью страниц
Страница 5 /
18
![AMERICAN DJ Focus Spot ONE [5/18] Power supply](/views2/2014198/page5/bg5.png)
ADJ Products, LLC - www.adj.com - Focus Spot One Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Focus Spot One Instruction Manual Page 8
Power Supply: The ADJ Focus Spot One contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Focus Spot One can be controlled via DMX-512 proto-
col. The Focus Spot One has 2 DMX channel modes; 15 channel mode
& 17 channel mode. The DMX address is set elec-
tronically using the controls on the front panel of
the unit. Your unit and your DMX controller require
a approved DMX-512 110 Ohm Data cable for data
input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased at
almost all professional sound and lighting stores).
Focus Spot One DMX Set Up
Figure 1
Focus Spot One Base Layout
1
2 3
4
5
6
7
1. IRreceiver: ToreceivetheIR signal;
2. LED:
DMX On DMX inputpresent
MASTER On MasterMode
SL AVE ON Slave Mode
SOUND Flashing Sound activation
3. Button:
MENU Toselecttheprogramming functions
UP Togoforward intheselectedfunctions
DOWN Togobackwardintheselectedfunctions
ENTER Toconrmtheselectedfunctions
4. Display:To showthevariousmenusandtheselectedfunction;
5. DMXIn/Out: 3‐pinXLRconnectorsforDMX512operation;
6. PowerIn/out: Connectors for powerinput/output;
7. Fuse(T6.3Amp): Protectstheunitfromover‐voltageorshortcircuit.
Содержание
116- User instructions
- Focus spot one
- Introduction
- Customer support
- Caution
- Warning
- Unpacking
- Suspender screew
- Mm 7 5
- Mm 14 7
- Power supply
- Dmx 512
- Pin 4 do not use
- Notice
- Not used
- Ground shield
- Focus spot one dmx set up
- Data true signal
- Data compliment signal
- Conductor 5 pin xlr male in 3 pin xlr female out
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior
- Your cables should be made with a male and female xlr connector on either end of the cable also remember that dmx cable must be daisy chained and cannot be split
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior
- Special note line termination
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion
- Pin xlr to 5 pin xlr conversion
- Pin xlr dmx connectors
- Pin 5 do not use
- Focus spot one 15 channel mode
- Channel value function
- Gobo 4 gobo 5 gobo 6
- Gobo 1 gobo 2 gobo 3
- Focus spot one 17 channel mode
- Focus spot one 15 channel mode
- Channel value function
- Focus spot one 17 channel mode
- Channel value function
- Gobo 4 gobo 5 gobo 6
- Gobo 1 gobo 2 gobo 3
- This will let you set unit as a master or slave in a master slave configuration
- This will let you select your desired dmx channel mode
- System menu when making adjustments press enter to confirm your setup then press and hold the menu button for at least 3 seconds to exit without making any adjust ments press the menu button the display will lock after 30 seconds press the menu button for 3 seconds to unlock
- Slave mode
- Set the dmx address
- Dmx addres
- Channel mod
- Pan inversion
- Pan inver
- Last stat
- In this mode you can select the dimmer curve
- In this mode you can adjust the sound sensitivity of the sound active mode
- In this mode the unit will run in sound active mode
- Dimmer curv
- This mode can be used as a precaution mode that in case the dmx signal is lost the operating mode chosen in the setup is the running mode the fixture will go into when the dmx signal is lost you can also set this as
- The operating mode you would like the unit to return to when power is applied
- Sound stat
- Sound sens
- Show modes 0 4 factory programs show mode can run with or without sound active mode active
- Show mod
- Tilt inver
- This will display the firmware soft ware version
- This function will run a self test program
- This function will restore all factory settings
- Software versio
- Pro default
- Fixture temp
- Fixture hour
- Back ligh
- Auto tes
- With this function you can make the back light automatically turn off after one minute
- With this function you can display the running time of the unit
- With this function you can display the running temperature of the unit
- Use this function to reset the motors
- Tilt inversion
- Tilt offse
- Setting adjustment for the gobo wheel
- Setting adjustment for the focus
- Setting adjustment for the color wheel
- Pan offse
- Gobo offse
- Focus offse
- Color offse
- Adjustment of the tilt home position
- Adjustment of the pan home position
- Master slave operation
- Universal dmx control
- Sound active mode
- Show mode
- To remove the gobo holder gently pull the gobo holder to wards the front of the unit and slide it up and out
- To change a gobo rotate the moving head so that the uv lens is located on top unscrew the single middle screw see instruction number 1 on the next page
- The gobo s in this unit are interchangable please be very care ful when replacing the gobo caution never open the unit when in use always disconnect the main power before attempting to change the gobos
- Reassemble the unit
- Once you loosen the single screw you are able to swing the head back see instruction number 2 on the next page you will now be able to access the gobo wheel turn the wheel with your hand until you come across the gobo you would like to change
- Gently and carefully remove the retainer ring after the re tainer ring is removed carefully remove the gobo 5 change the gobo and replace the retainer ring carefully slide the gobo holder back into the housing slot
- Unscrew the single screw 2 flip the top cover back
- Remove the lens 4 unscrew the 4 screws located on the other side
- Focus spot one removing the head casing
- Focus spot one photometric chart
- Focus spot one dimmer curve chart
- Be sure the external fuse has not blown the fuse is located on the rear panel of the unit 2 be sure the fuse holder is completely and properly seated unit does not respond to sound
- Adj products llc www adj com focus spot one instruction manual page 32 adj products llc www adj com focus spot one instruction manual page 33
- Trouble shooting listed below are a few common problems that you may encounter with solutions
- No light output from the unit
- Low frequencies bass should cause the unit to react to sound tapping on the microphone quiet or high pitched sounds may not activate the unit
- Locate and remove the unit s powercon cord once the cord has been removed the fuse holder is located next to the power socket use a philips head screw driver unscrew the fuse holder remove the bad fuse and replace with a new one
- Focus spot one warranty
- Focus spot one trouble shooting
- Focus spot one fuse replacement
- Focus spot one cleaning
- Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses and mirror should be carried out periodically to optimize light output cleaning frequency depends on the environ ment in which the fixture operates i e smoke fog residue dust dew in heavy club use we recommend cleaning on a monthly basis periodic cleaning will ensure longevity and crisp output 1 use normal glass cleaner and a soft cloth to wipe down the out side casing 2 use a brush to wipe down the cooling vents and fan grill 3 clean the external optics with glass cleaner and a soft cloth every 20 days 4 clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 always be sure to dry all parts completely before plugging the unit back in
- This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source adj products llc 6122 s eastern ave los angeles ca 90040 usa tel 323 582 2650 fax 323 725 6100 web www adj com e mail info americandj com
- Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice
- Please note
- Model focus spot one
- Auto sensing voltage
- A d j supply europe b v junostraat 2 6468 ew kerkrade the netherlands service adjgroup eu www adj eu tel 31 45 546 85 00 fax 31 45 546 85 99
Похожие устройства
-
AMERICAN DJ Vizi QWash7Руководство по эксплуатации -
AMERICAN DJ Vizi Hex Wash7Руководство по эксплуатации -
Involight PROSPOT500SETРуководство по эксплуатации -
DIALIGHTING Mini Spot 50Руководство по эксплуатации -
DIALIGHTING MINI BEAM 150 MKIIРуководство по эксплуатации -
DIALIGHTING Profile BSW 400Руководство по эксплуатации -
DIALIGHTING WASH ZOOM 19x40Руководство по эксплуатации -
DIALIGHTING Wash Zoom 700Руководство по эксплуатации -
Involight MH78WРуководство по эксплуатации -
DIALIGHTING IW30-15 zoomРуководство по эксплуатации -
Involight MH255WРуководство по эксплуатации -
Involight MH575S OLDРуководство по эксплуатации
Узнайте, как правильно подключить и настроить осветительное оборудование с помощью DMX-512. Подробные инструкции и советы по использованию.