![AMERICAN DJ Focus Spot ONE [17/18] Focus spot one cleaning](/img/pdf.png)
AMERICAN DJ Focus Spot ONE [17/18] Focus spot one cleaning
![AMERICAN DJ Focus Spot ONE [17/18] Focus spot one cleaning](/views2/2014198/page17/bg11.png)
ADJ Products, LLC - www.adj.com - Focus Spot One Instruction Manual Page 32 ADJ Products, LLC - www.adj.com - Focus Spot One Instruction Manual Page 33
Focus Spot One Cleaning
Focus Spot One Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environ-
ment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Focus Spot One Fuse Replacement
Locate and remove the unit’s PowerCon cord. Once the cord has been
removed the fuse holder is located next to the power socket. Use a
philips head screw driver unscrew the fuse holder. Remove the bad
fuse and replace with a new one.
Focus Spot One Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-
ranty). Only the L.E.D.s carry a 2-year warranty (excludingStarTecSerieswhichacarriesa1Year
LimitedWarranty)Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)
Содержание
- User instructions p.1
- Focus spot one p.1
- Customer support p.2
- Caution p.2
- Warning p.2
- Unpacking p.2
- Introduction p.2
- Suspender screew p.4
- Mm 7 5 p.4
- Mm 14 7 p.4
- Power supply p.5
- Dmx 512 p.5
- Notice p.6
- Not used p.6
- Ground shield p.6
- Focus spot one dmx set up p.6
- Data true signal p.6
- Data compliment signal p.6
- Conductor 5 pin xlr male in 3 pin xlr female out p.6
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior p.6
- Your cables should be made with a male and female xlr connector on either end of the cable also remember that dmx cable must be daisy chained and cannot be split p.6
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior p.6
- Special note line termination p.6
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion p.6
- Pin xlr to 5 pin xlr conversion p.6
- Pin xlr dmx connectors p.6
- Pin 5 do not use p.6
- Pin 4 do not use p.6
- Focus spot one 15 channel mode p.7
- Channel value function p.7
- Gobo 4 gobo 5 gobo 6 p.8
- Gobo 1 gobo 2 gobo 3 p.8
- Focus spot one 17 channel mode p.8
- Focus spot one 15 channel mode p.8
- Channel value function p.8
- Channel value function p.9
- Gobo 4 gobo 5 gobo 6 p.9
- Gobo 1 gobo 2 gobo 3 p.9
- Focus spot one 17 channel mode p.9
- This will let you set unit as a master or slave in a master slave configuration p.10
- This will let you select your desired dmx channel mode p.10
- System menu when making adjustments press enter to confirm your setup then press and hold the menu button for at least 3 seconds to exit without making any adjust ments press the menu button the display will lock after 30 seconds press the menu button for 3 seconds to unlock p.10
- Slave mode p.10
- Set the dmx address p.10
- Dmx addres p.10
- Channel mod p.10
- Pan inver p.11
- Last stat p.11
- In this mode you can select the dimmer curve p.11
- In this mode you can adjust the sound sensitivity of the sound active mode p.11
- In this mode the unit will run in sound active mode p.11
- Dimmer curv p.11
- This mode can be used as a precaution mode that in case the dmx signal is lost the operating mode chosen in the setup is the running mode the fixture will go into when the dmx signal is lost you can also set this as p.11
- The operating mode you would like the unit to return to when power is applied p.11
- Sound stat p.11
- Sound sens p.11
- Show modes 0 4 factory programs show mode can run with or without sound active mode active p.11
- Show mod p.11
- Pan inversion p.11
- This will display the firmware soft ware version p.12
- This function will run a self test program p.12
- This function will restore all factory settings p.12
- Software versio p.12
- Pro default p.12
- Fixture temp p.12
- Fixture hour p.12
- Back ligh p.12
- Auto tes p.12
- With this function you can make the back light automatically turn off after one minute p.12
- With this function you can display the running time of the unit p.12
- With this function you can display the running temperature of the unit p.12
- Use this function to reset the motors p.12
- Tilt inversion p.12
- Tilt inver p.12
- Tilt offse p.13
- Setting adjustment for the gobo wheel p.13
- Setting adjustment for the focus p.13
- Setting adjustment for the color wheel p.13
- Pan offse p.13
- Gobo offse p.13
- Focus offse p.13
- Color offse p.13
- Adjustment of the tilt home position p.13
- Adjustment of the pan home position p.13
- Universal dmx control p.14
- Sound active mode p.14
- Show mode p.14
- Master slave operation p.14
- To remove the gobo holder gently pull the gobo holder to wards the front of the unit and slide it up and out p.15
- To change a gobo rotate the moving head so that the uv lens is located on top unscrew the single middle screw see instruction number 1 on the next page p.15
- The gobo s in this unit are interchangable please be very care ful when replacing the gobo caution never open the unit when in use always disconnect the main power before attempting to change the gobos p.15
- Reassemble the unit p.15
- Once you loosen the single screw you are able to swing the head back see instruction number 2 on the next page you will now be able to access the gobo wheel turn the wheel with your hand until you come across the gobo you would like to change p.15
- Gently and carefully remove the retainer ring after the re tainer ring is removed carefully remove the gobo 5 change the gobo and replace the retainer ring carefully slide the gobo holder back into the housing slot p.15
- Unscrew the single screw 2 flip the top cover back p.16
- Remove the lens 4 unscrew the 4 screws located on the other side p.16
- Focus spot one removing the head casing p.16
- Focus spot one photometric chart p.16
- Focus spot one dimmer curve chart p.16
- Adj products llc www adj com focus spot one instruction manual page 32 adj products llc www adj com focus spot one instruction manual page 33 p.17
- Trouble shooting listed below are a few common problems that you may encounter with solutions p.17
- No light output from the unit p.17
- Low frequencies bass should cause the unit to react to sound tapping on the microphone quiet or high pitched sounds may not activate the unit p.17
- Locate and remove the unit s powercon cord once the cord has been removed the fuse holder is located next to the power socket use a philips head screw driver unscrew the fuse holder remove the bad fuse and replace with a new one p.17
- Focus spot one warranty p.17
- Focus spot one trouble shooting p.17
- Focus spot one fuse replacement p.17
- Focus spot one cleaning p.17
- Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses and mirror should be carried out periodically to optimize light output cleaning frequency depends on the environ ment in which the fixture operates i e smoke fog residue dust dew in heavy club use we recommend cleaning on a monthly basis periodic cleaning will ensure longevity and crisp output 1 use normal glass cleaner and a soft cloth to wipe down the out side casing 2 use a brush to wipe down the cooling vents and fan grill 3 clean the external optics with glass cleaner and a soft cloth every 20 days 4 clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 always be sure to dry all parts completely before plugging the unit back in p.17
- Be sure the external fuse has not blown the fuse is located on the rear panel of the unit 2 be sure the fuse holder is completely and properly seated unit does not respond to sound p.17
- This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source adj products llc 6122 s eastern ave los angeles ca 90040 usa tel 323 582 2650 fax 323 725 6100 web www adj com e mail info americandj com p.18
- Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice p.18
- Please note p.18
- Model focus spot one p.18
- Auto sensing voltage p.18
- A d j supply europe b v junostraat 2 6468 ew kerkrade the netherlands service adjgroup eu www adj eu tel 31 45 546 85 00 fax 31 45 546 85 99 p.18
Похожие устройства
-
AMERICAN DJ Vizi QWash7Руководство по эксплуатации -
AMERICAN DJ Vizi Hex Wash7Руководство по эксплуатации -
Involight PROSPOT500SETРуководство по эксплуатации -
DIALIGHTING Mini Spot 50Руководство по эксплуатации -
DIALIGHTING MINI BEAM 150 MKIIРуководство по эксплуатации -
DIALIGHTING Profile BSW 400Руководство по эксплуатации -
DIALIGHTING WASH ZOOM 19x40Руководство по эксплуатации -
DIALIGHTING Wash Zoom 700Руководство по эксплуатации -
Involight MH78WРуководство по эксплуатации -
DIALIGHTING IW30-15 zoomРуководство по эксплуатации -
Involight MH255WРуководство по эксплуатации -
Involight MH575S OLDРуководство по эксплуатации