Hikoki li-ion (DS12DA) [10/36] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hikoki li-ion (DS12DA) [10/36] English

Hikoki DS12DA (DS12DARFZ) [10/36] English
10
English
○ Since the built-in micro computer takes about 3
seconds to confi rm that the battery being charged with
charger is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
○ If the pilot lamp does not blink in red (every second)
even though the charger cord is connected to the power,
it indicates that the protection circuit of the charger may
be activated.
Remove the cord or plug from the power and then
connect it again after 30 seconds or so. If this does
not cause the pilot lamp to blink in red (every second),
please take the charger to the HiKOKI Authorized
Service Center.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery 2 2
Charging 3 2
Selecting the mode 4 2
Tightening torque adjustment 5 2
Selecting the drill position 6 3
Selecting the impact position 7 3
Change rotation speed 8 3
How to use the LED light 9 3
Mounting the bit 10 3
Reversing the rotational direction 11 4
Switch operation 12 4
Mounting the hook (sold separately) 13 4
Remaining battery indicator 14 4
Selecting accessories ― 31
LED LIGHT WARNING SIGNALS
This product features functions that are designed to protect
the tool itself as well as the battery. If any of the safeguard
functions are triggered during operation, the LED light will
blink as described in Table 3. When any of the safeguard
functions are triggered, immediately remove your fi nger
from the switch and follow the instructions described under
corrective action.
Table 3
Safeguard Function LED Light Display Corrective Action
Overload Protection
On 0.25 second/off 0.25 second
If the operating with the shift knob set on
HIGH, adjust to LOW and continue operation.
Remove the cause of the overload.
Temperature Protection Allow the tool and battery to thoroughly cool.
Low Voltage Protection Recharge the battery.
MAINTENANCE AND INSPECTION
1. Inspecting the tool
Since use of as dull tool will degrade effi ciency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
When the driver drill is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
5. Storage
Store the driver drill in a place in which the temperature
is less than 40°C and out of reach of children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modifi ed (such as
disassembly and replacement of cells or other internal
parts).
0000BookDS12DA.indb100000BookDS12DA.indb10 2019/02/0710:38:162019/02/0710:38:16

Содержание

Похожие устройства

Скачать