Makita CXT SC103DZ [12/36] Guide scale
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Makita CXT SC103DZ [12/36] Guide scale

Makita CXT SC103DZ [12/36] Guide scale
12 ENGLISH
Reversing switch lever
WARNING:
When not operating the tool, always
set the reversing switch lever to the lock position.
CAUTION: Always make sure the position of
the reversing switch lever before operating.
NOTICE: Do not move the reversing switch lever
when the switch trigger is being pulled.Thismay
cause a damage to the tool.
To start the cutting operation, set the reversing switch
lever to cutting position.
Toreversethecuttingsequence,setthereversing
switchlevertothereversingposition.Whenyoucon-
tinuetopulltheswitchtrigger,thejawofthecuttingdie
opensandstopsatfullyopenedposition.
To lock the switch trigger, set the reversing switch lever to the
lockposition.Theswitchtriggercannotbepulledinthisposition.
►Fig.6: 1. Reversing switch lever 2. Cutting position
3. Lock position 4. Reversing position
NOTICE:
When the reversing switch lever is in the
reversing position, run the tool only as needed. To
preventthedamagetothetool,thetoolwillautomatically
stopswhenitisruninthereversingpositioncontinuously.
NOTE:Aftercutting,ifyoureleasetheswitchtrigger
whilethejawofthecuttingdieisopeningandthenset
the reversing switch lever to the reversing position,
thejawwilloncecloseandthenopenwhenyoupull
the switch trigger again.
LED light
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keepsonlightingwhiletheswitchtriggerisbeingpulled.
Thelampgoesoutapproximately15secondsafter
releasing the switch trigger.
►Fig.7: 1.Lamp(inside)
NOTE:Useadryclothtowipethedirtoffthelensof
the lamp. Be careful not to scratch the lens of lamp, or
itmaylowertheillumination.
NOTE: When the tool is overheated, the lamp will
blink.Letthetoolcooldowninthiscase.
Guide scale
Usetheguidescaleifyouwishtocutthreadedrodsin
the same length. Insert the guide scale into the hole as
showninthegure.
►Fig.8: 1. Guide scale 2. Clamping screw
Alignthevalueofyourdesiredlengthontheguidescale
with the cutting line. Then tighten the clamping screw.
►Fig.9:
1. Guide scale 2. Cutting line 3. Clamping screw
CAUTION: Do not hold the guide scale to
carry or handle the tool.Thetoolmayfalloffand
causepersonalinjuryand/ordamagetothetool.
Rod guide
For a precise cutting, set the rod guide in position
dependingonthediameterofthethreadedrodtobe
cut.
►Fig.10: 1.Rodguide(Position1)2. Rod guide
(Position2)
There are two rod guide positions.
Position Size of threaded rod
1 W3/8, 3/8-16UNC, M10
2 W5/16, W1/4, 5/16-18UNC, 1/4-20UNC,
M8, M6
Hook
CAUTION: Never hook the tool on a windy
location or a potentially unstable surface.
CAUTION: Do not use the hook when it is
deformed or damaged.
CAUTION: When not operating the tool,
always fold the hook.
Thehookisconvenientforhangingthetooltemporarily.
►Fig.11: 1. Hook
CAUTION: Do not hang the hook from the
waist belt.Itmayresultinpersonalinjuriesand/or
damage to the tool if dropped.
►Fig.12
Hex wrench storage
When not in use, store the hex wrench as shown in the
guretokeepitfrombeinglost.
►Fig.13: 1. Hex wrench
Shoulder strap
Optional accessory
Shoulderstrapisusefulforcarryingthetool.
►Fig.14: 1. Shoulder strap 2. Belt end 3. Buckle
CAUTION: Always wear the shoulder strap
crossed over your body and adjusted in proper
length.
CAUTION: Do not use the shoulder strap if it
is damaged.
CAUTION: Leave an sufcient length between
the buckle and belt end to prevent the belt end
from slipping through the buckle.

Содержание

Похожие устройства

Скачать