Makita CXT SC103DZ [13/36] Assembly
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Makita CXT SC103DZ [13/36] Assembly

Makita CXT SC103DZ [13/36] Assembly
13 ENGLISH
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing the cutting dies
CAUTION: Always install the cutting dies
in the correct directions and secured rmly.
Incorrectorlooseattachmentmaycausebreakageof
thecuttingdie,resultingpersonalinjurybyownoff
fractions.
NOTICE: Remove the burr on the cutting dies
using a le if any.
1. Checkifthejawofthecuttingdieisfullyopened.
Ifnot,installthebatteryandpulltheswitchtriggeruntil
thejawisfullyopened.
CAUTION: Be sure to remove the battery
cartridge if you installed.
2. Set the reversing switch lever to the lock position.
►Fig.15: 1. Reversing switch lever
3. Unscrewtheboltswiththesuppliedhexwrench.
CAUTION: Use only the Makita wrench pro-
vided with the tool.Usingotherwrenchesmay
resultinovertighteningorinsufcienttighteningwhich
causespersonalinjury.
4. Set the cutting dies onto the mounts so that the
twocoloredmarkingscanbeseen.
►Fig.16: 1. Bolt 2. Cutting die 3.Stationarymount
4.Movablemount5. Colored marking
6. Hex wrench
5. Securethecuttingdieswiththeboltsrmly.
Thecuttingdiesarecorrectlyinstalledifthearrowson
them point each other. The dimensions of the cutting
diesarethesamebuttheirthicknesslookdifferent
whenseenfromabove.
►Fig.17: 1.Arrow2. Cutting die 3. Thin side 4. Thick
side
OPERATION
CAUTION: Make sure that the correct size of
the cutting dies are installed to the tool. Check
the cutting capacity written on the cutting dies
before cutting.
CAUTION: Before pulling the switch trigger,
be sure to set the threaded rod so that its thread
ts with those of cutting dies. Incorrect alignment
ofthethreadsmaybreakthecuttingdieandcause
personalinjurybyownofffractions.
CAUTION: Replace the cutting dies if the
cutting edge is chipped or deformed.
When cutting, place the threaded rod perpendicular to
thecuttinglineasshowninthegure.
►Fig.18: 1. Cutting line
NOTE: When cutting a threaded rod made of ductile
metalsuchasstainlesssteel,burrsmaybegenerated
onthecutend.Removeburrswithaleinthiscase.
►Fig.19: 1. Threaded rod 2. Burr
Cutting secured threaded rods
When cutting a threaded rod which is secured to the
buildingstructuresuchastheceiling,wall,oor,etc.,
followtheprocedurebelow:
►Fig.20: 1. Threaded rod 2. Cutting die on the sta-
tionarymount
1. Bring the tool so that the threaded rod is posi-
tionedbetweenthecuttingdies.
2. While the threaded rod contacting with the rod
guide,tthethreadoftherodwiththatofthecuttingdie
onthestationarymount.
3. Pullandholdtheswitchtriggeruntilthecutting
isnishedandthejawofthecuttingdiecomestofully
opened position.
NOTICE: Clean the front face of the tool and the
tip of the guide scale before operation.Theymay
dirtythecontactingsurface.
Cutting loose threaded rods
Whencuttingaloosethreadedrodontheoorora
worktable,followtheprocedurebelow:
►Fig.21: 1. Threaded rod 2. Cutting die on the sta-
tionarymount
1. Positionathreadedrodbetweenthecuttingdies.
2. While the threaded rod contacting with the rod
guide,tthethreadoftherodwiththatofthecuttingdie
onthestationarymount.
3. Pullandholdtheswitchtriggeruntilthecutting
isnishedandthejawofthecuttingdiecomestofully
opened position.
When cutting a long threaded rod which is hard to hold
byhand,placethetoolasillustrated.Thetoolcanbe
placedat.Thecoveralsocanbeusedforsupporting
the end of the threaded rod.
►Fig.22: 1.Cover(Position1)2.Rodguide(Position
1)3.Cover(Position2)4. Rod guide
(Position2)
The cover has markings to indicate its position.
Depending on the size of the threaded rod, put the
coverinthepositionasshowninthetableaswellasthe
rod guide.
Position Size of threaded rod
1 W3/8, 3/8-16UNC, M10
2 W5/16, W1/4, 5/16-18UNC, 1/4-20UNC,
M8, M6

Содержание

Похожие устройства

Скачать