![D-Link DMC-1910T [4/12] Product features](/img/pdf.png)
D-Link DMC-1910T [4/12] Product features
![D-Link DMC-1910T [4/12] Product features](/views2/1166204/page4/bg4.png)
4
Product Features
y A pair of one-channel media conversion between 1000BASE-TX and 1000BASE-LX
y Two different type of transmitting wavelength: One wavelength with bi-directional for both
transmit and receive. TX: 1310nm; RX: 1550nm. or TX: 1550nm; RX: 1310nm
y Link Pass Through function
y Auto MDI/MDI-X for TX port
y Full wire-speed forwarding rate
y Front panel status LEDs
y Used as a stand-alone device or with a chassis
y Hot-swappable when used with a chassis
Содержание
- Dmc 1910 1000base tx to 1000base lx 1
- Manual 1
- Single fiber dual wavelength media converter kit 1
- Ontents 2
- About link pass through 3
- About media converter 3
- Dual wavelength single fiber 3
- Introduction 3
- Product features 4
- Connecting to power 5
- Installation 5
- Installing in a chassis 5
- Selecting a site for the equipment 5
- Monitoring the converter through management module 6
- Led indicator 7
- The led indicators give you instant feedback on status of the converter 7
- Link pass through function 8
- Llcf link loss carry forward when a device connected to the converter and the tp line loss the link the converter s fiber will disconnect the link of transmit so that the other ends will know that there is a linkage error on this end and when the fiber line loss the link the converter s tp will disconnected and the other end will know that there is linkage problem exist there is a default llcf setting on this converter 8
- The table below shows how llcf function is working 8
- Llr link loss return when a device connected to the converter and the fiber line loss the link the converter s fiber will disconnect the link of transmit there is a switch to enable or disable the function of the media converter 9
- The table below shows how llr function is working 9
- Switch 10
- Switch 1 fiber mode switch 10
- Switch 2 llr 10
- There is a two pin dip switch on the module which define as switch 1 and switch 2 10
- When the switch was turned to on it means that the fiber was turned to forced mode and off for auto negotiation mode 10
- When the switch was turned to on it means that the llr was enabled and off for disabled 10
- Specifications 11
- Ordering information 12
- Please include the following information when ordering 1 fiber type single mode 2 fiber connector type sc 3 segment distance range for the fiber port 12
Похожие устройства
- D-Link DMC-1000 Инструкция по эксплуатации
- D-Link KVM-221 Инструкция по эксплуатации
- D-Link DKVM-4U Инструкция по эксплуатации
- D-Link KVM-121 Инструкция по эксплуатации
- D-Link DUB-H7/B на 7 портов Инструкция по эксплуатации
- D-Link DKVM-4K Инструкция по эксплуатации
- Daewoo Electronics fr 092aix Инструкция по эксплуатации
- Daewoo Electronics fr 082aix(r) Инструкция по эксплуатации
- Daewoo Electronics fr-051ar Инструкция по эксплуатации
- Daewoo Electronics electronics fn-102 cw Инструкция по эксплуатации
- Daewoo Electronics electronics fn-103 cm Инструкция по эксплуатации
- Daewoo Electronics electronics fn-153 cm Инструкция по эксплуатации
- Daewoo Electronics electronics fn-153 cw Инструкция по эксплуатации
- Daewoo DAST 551 Инструкция по эксплуатации
- Daewoo DAST 2500E Инструкция по эксплуатации
- Daewoo DAST 6555 Инструкция по эксплуатации
- Daewoo DAT 1700E Инструкция по эксплуатации
- Daewoo DAT 2500E Инструкция по эксплуатации
- Daewoo DAT 4555 Инструкция по эксплуатации
- Daewoo DAT 3555 Инструкция по эксплуатации