![Makita 9237cb [6/52] Assembly](/img/pdf.png)
Makita 9237cb [6/52] Assembly
![Makita 9237cb [6/52] Assembly](/views2/1175381/page6/bg6.png)
6
Speed adjusting dial (Fig. 3)
The tool speed can be changed by turning the speed
adjusting dial to a given number setting from 1 to 6. (At
the time when the switch trigger is fully pulled.)
Higher speed is obtained when the dial is turned in the
direction of number 6. And lower speed is obtained when
it is turned in the direction of number 1.
Refer to the table for the relationship between the
number settings on the dial and the approximate tool
speed.
014945
CAUTION:
• If the tool is operated continuously at low speeds for a
long time, the motor will get overloaded, resulting in
tool malfunction.
• The speed adjusting dial can be turned only as far as 6
and back to 1. Do not force it past 6 or 1, or the speed
adjusting function may no longer work.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
• Always install the loop handle or the side grip.
Removing or installing head cover (Fig. 4)
To remove the head cover, perform the following steps:
1. Remove the screw on the head cover with
screwdriver.
2. Remove the head cover as shown in the figure.
To install the head cover, perform the above steps in
reverse.
Installing loop handle
CAUTION:
• Always be sure that the loop handle is installed
securely before operation.
Always install the loop handle on the tool before
operation. Hold the tool’s switch handle and the loop
handle firmly with both hands during operation.
Install the loop handle so that its protrusion will fit into the
matching hole in the gear housing. (Fig. 5)
Install the bolts and tighten them with the hex wrench.
The loop handle can be installed in two different
directions as shown in the figures whichever is
convenient for your work. (Fig. 6 & 7)
For tools which are equipped with a backing pad.
Installing or removing the wool pad (optional
accessory) (Fig. 8)
To install the wool pad, first remove all dirt or foreign
matter from the backing pad. Press the shaft lock and
screw the backing pad onto the spindle. Insert the sleeve
18 into the center hole of the backing pad.
Using the sleeve 18 as a positioning guide, install the
wool pad on the backing pad with the sleeve 18 inserted
through the center hole of the wool pad. Then remove
the sleeve 18 from the backing pad.
To remove the wool pad, just tear it off the backing pad.
Then unscrew the backing pad while pressing the shaft
lock.
For tools which are equipped with a rubber pad.
Installing or removing the wool bonnet (optional
accessory)
Mount the rubber pad onto the spindle. Screw the lock
nut onto the spindle. (Fig. 9)
To tighten the lock nut, press the shaft lock firmly so that
the spindle cannot revolve, then use the lock nut wrench
and securely tighten clockwise.
To remove the rubber pad, follow the installation
procedure in reverse. (Fig. 10)
Fit the wool bonnet over the rubber pad. Tie a bow knot
and tuck the knot and any loose strings between the wool
bonnet and the rubber pad. (Fig. 11)
Installing side grip (handle) (optional accessory)
(Fig. 12)
CAUTION:
• Always be sure that the side grip is installed securely
before operation.
Screw the side grip securely on the position of the tool as
shown in the figure.
OPERATION
Polishing operation (Fig. 13)
CAUTION:
• Always wear safety glasses or a face shield during
operation.
Hold the tool firmly. Turn the tool on and then apply the
wool pad/bonnet to the workpiece.
In general, keep the wool pad/bonnet at an angle of
about 15 degrees to the workpiece surface.
Apply slight pressure only. Excessive pressure will result
in poor performance and premature wear to wool pad/
bonnet.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Cleaning the dust cover (Fig. 14)
Clean the dust cover when necessary as following steps:
1. Remove the screw on the dust cover.
2. Remove the dust cover.
3. Wipe the dust cover to remove dirt.
4. Align the hook of the dust cover with groove on the
handle.
5. Tighten the dust cover with the screw.
If the dust cover is broken or becomes extremely dirty,
replace it.
Number min
–1
(RPM)
1 600
2 900
31,500
42,100
52,700
63,200
Содержание
- English 4
- Explanation of general view 4
- General power tool safety warnings 4
- Polisher safety warnings 4
- Specifications 4
- Functional description 5
- Save these instructions 5
- Shaft lock fig 1 5
- Switch action fig 2 5
- Assembly 6
- Cleaning the dust cover fig 14 6
- For tools which are equipped with a backing pad 6
- For tools which are equipped with a rubber pad 6
- Installing loop handle 6
- Installing or removing the wool bonnet optional accessory 6
- Installing or removing the wool pad optional accessory fig 8 6
- Installing side grip handle optional accessory fig 12 6
- Maintenance 6
- Operation 6
- Polishing operation fig 13 6
- Removing or installing head cover fig 4 6
- Speed adjusting dial fig 3 6
- Ec declaration of conformity 7
- Optional accessories 7
- Replacing carbon brushes fig 15 16 7
- Consignes de sécurité générales pour outils électriques 8
- Consignes de sécurité pour polisseuse 8
- Descriptif 8
- Français 8
- Spécifications 8
- Assemblage 10
- Cadran de réglage de la vitesse fig 3 10
- Conservez ces instructions 10
- Description du fonctionnement 10
- Interrupteur fig 2 10
- Pose de la poignée arceau 10
- Pose et dépose du capot de la tête de polissage fig 4 10
- Verrou d axe fig 1 10
- Accessoires en option 11
- Entretien 11
- Nettoyage du capot anti poussière fig 14 11
- Polissage fig 13 11
- Pose de la poignée latérale accessoire en option fig 12 11
- Pose et dépose du bonnet en peau de mouton accessoire en option 11
- Pose et dépose du disque en peau de mouton accessoire en option fig 8 11
- Pour les outils équipés d un disque en caoutchouc 11
- Pour les outils équipés d un plateau de support 11
- Remplacement des charbons fig 15 et 16 11
- Utilisation 11
- Déclaration de conformité ce 12
- Allgemeine sicherheitswarnungen für elektrowerkzeuge 13
- Deutsch 13
- Sicherheitswarnungen für poliermaschine 13
- Technische daten 13
- Übersicht 13
- Abnehmen und anbringen der kopfabdeckung abb 4 15
- Bewahren sie diese hinweise sorgfältig auf 15
- Drehzahl stellrad abb 3 15
- Funktionsbeschreibung 15
- Montage 15
- Montage des bügelgriffs 15
- Schaftarretierung abb 1 15
- Schalterfunktion abb 2 15
- Anbringen und abnehmen der wollhaube sonderzubehör 16
- Anbringen und abnehmen des wollkissens sonderzubehör abb 8 16
- Auswechseln der kohlebürsten abb 15 u 16 16
- Betrieb 16
- Für werkzeuge die mit einem gummiteller ausgestattet sind 16
- Für werkzeuge die mit einem schleifteller ausgestattet sind 16
- Montieren des seitengriffs handgriff sonderzubehör abb 12 16
- Polierbetrieb abb 13 16
- Reinigen des staubfängers abb 14 16
- Sonderzubehör 16
- Wartung 16
- Eg übereinstimmungserklärung 17
- Avvertimenti generali per la sicurezza dell utensile elettrico 18
- Avvertimenti per la sicurezza della lucidatrice 18
- Dati tecnici 18
- Italiano 18
- Visione generale 18
- Conservate queste istruzioni 19
- Se il posto di lavoro è estremamente caldo e umido oppure molto contaminato da polveri conduttive usare un interruttore di corto circuito 30 ma per garantire la sicurezza dell operatore 19
- Azionamento dell interruttore fig 2 20
- Bloccaggio dell albero fig 1 20
- Descrizione funzionale 20
- Ghiera di regolazione velocità fig 3 20
- Installazione del manico ad anello 20
- Montaggio 20
- Rimozione o installazione del coperchio testa fig 4 20
- Accessori opzionali 21
- Funzionamento 21
- Installazione dell impugnatura laterale accessorio opzionale fig 12 21
- Installazione o rimozione del cappello di lana accessorio opzionale 21
- Installazione o rimozione del tampone di lana accessorio opzionale fig 8 21
- Manutenzione 21
- Operazione di lucidatura fig 13 21
- Per gli utensili dotati di un platorello di appoggio 21
- Per gli utensili dotati di un tampone di gomma 21
- Pulizia del coperchio antipolvere fig 14 21
- Sostituzione delle spazzole di carbone fig 15 e 16 21
- Dichiarazione ce di conformità 22
- Algemene veiligheidswaarschuwingen voor elektrisch gereedschap 23
- Nederlands 23
- Technische gegevens 23
- Veiligheidswaarschuwingen specifiek voor een polijstmachine 23
- Verklaring van algemene gegevens 23
- Aanbrengen of verwijderen van de wollen poetsschijf optioneel accessoire fig 8 25
- Asvergrendeling fig 1 25
- Beschrijving van de functies 25
- Bewaar deze voorschriften 25
- Ineenzetten 25
- Installeren van de d handgreep 25
- Toerentalregelknop fig 3 25
- Verwijderen of aanbrengen van de kopafdekking fig 4 25
- Voor werktuigen voorzien van een steunschijf 25
- Werking van de trekschakelaar fig 2 25
- Aanbrengen of verwijderen van de wollen kap optioneel accessoire 26
- Bediening 26
- Monteren van de zijhandgreep het handvat optioneel accessoire fig 12 26
- Onderhoud 26
- Optionele accessoires 26
- Polijsten fig 13 26
- Reinigen van de stofkap fig 14 26
- Vervangen van de koolborstels fig 15 en 16 26
- Voor werktuigen voorzien van een rubberschijf 26
- Eu verklaring van conformiteit 27
- Advertencias de seguridad generales para herramientas eléctricas 28
- Advertencias de seguridad para la pulidora 28
- Español 28
- Especificaciones 28
- Explicación de los dibujos 28
- Accionamiento del interruptor fig 2 30
- Bloqueo del eje fig 1 30
- Descripción funcional 30
- Desmontaje o instalación de la cubierta del cabezal fig 4 30
- Dial de ajuste de velocidad fig 3 30
- Guarde estas instrucciones 30
- Instalación del mango curvado 30
- Montaje 30
- Accesorios opcionales 31
- Instalación de la empuñadura lateral mango accesorio opcional fig 12 31
- Instalación o desmontaje de la caperuza de lana accesorio opcional fig 8 31
- Instalación o desmontaje de la capucha de lana accesorio opcional 31
- Limpieza de la cubierta contra el polvo fig 14 31
- Mantenimiento 31
- Operación 31
- Operación de pulido fig 13 31
- Para herramientas que están equipadas con un plato de apoyo 31
- Para herramientas que están equipadas con un plato de caucho 31
- Reemplazo de las escobillas de carbón fig 15 y 16 31
- Declaración de conformidad ce 32
- Advertências de segurança da politriz 33
- Avisos gerais de segurança para ferramentas eléctricas 33
- Especificações 33
- Explicação geral 33
- Português 33
- Guarde estas instruções 34
- Assemblagem 35
- Bloqueio do veio fig 1 35
- Descrição funcional 35
- Instalação da pega auxiliar 35
- Instalação ou remoção da almofada de lã acessório opcional fig 8 35
- Interruptor fig 2 35
- Marcador de regulação da velocidade fig 3 35
- Para ferramentas equipadas com uma almofada de protecção 35
- Remover ou instalar a tampa da cabeça fig 4 35
- Acessórios opcionais 36
- Instalar a pega lateral manípulo acessório opcional fig 12 36
- Instalação ou remoção da touca de lã acessório opcional 36
- Limpar a protecção contra poeira fig 14 36
- Manutenção 36
- Operação 36
- Para ferramentas equipadas com uma almofada de borracha 36
- Polimento fig 13 36
- Substituição das escovas de carvão fig 15 e 16 36
- Declaração de conformidade ce 37
- Almindelige sikkerhedsregler for el værktøj 38
- Illustrationsoversigt 38
- Sikkerhedsadvarsler for poleremaskine 38
- Specifikationer 38
- Afbryderkontaktbetjening fig 2 39
- Funktionsbeskrivelse 39
- Gem disse forskrifter 39
- Spindellås fig 1 39
- Afmontering eller montering af hoveddækslet fig 4 40
- Betjening 40
- For maskiner der er udstyret med en bagskive 40
- For maskiner der er udstyret med en gummiskive 40
- Hastighedsvælgerknap fig 3 40
- Montering af hjælpehåndtaget 40
- Montering af sidegreb håndtag ekstraudstyr fig 12 40
- Montering eller afmontering af polerehætten ekstraudstyr 40
- Montering eller afmontering af polereskiven ekstraudstyr fig 8 40
- Polering fig 13 40
- Samling 40
- Ekstraudstyr 41
- Eu konformitetserklæring 41
- Rengøring af støvdækslet fig 14 41
- Udskiftning af kul fig 15 og 16 41
- Vedligeholdelse 41
- Γενικές προειδοποιήσεις ασφαλείας για το ηλεκτρικό εργαλείο 42
- Ελληνικα 42
- Περιγραφή γενικής άποψης 42
- Προειδοποιησεισ ασφαλειασ στιλβωτη 42
- Τεχνικα χαρακτηριστικα 42
- Αφαίρεση ή τοποθέτηση του καλύμματος κεφαλής εικ 4 44
- Κλείδωμα άξονα εικ 1 44
- Κουμπί ρύθμισης ταχύτητος εικ 3 44
- Λειτουργία διακόπτη εικ 2 44
- Περιγραφη λειτουργιασ 44
- Συναρμολογηση 44
- Φυλαξετε αυτεσ τισ οδηγιεσ 44
- Αντικατάσταση ψηκτρών άνθρακα εικ 15 και 16 45
- Για εργαλεία που είναι εξοπλισμένα με ελαστικό πέλμα 45
- Για εργαλεία που είναι εξοπλισμένα με υπόθεμα υποστήριξης 45
- Εργασία στίλβωσης εικ 13 45
- Καθαρισμός του καλύμματος σκόνης εικ 14 45
- Λειτουργία 45
- Συντηρηση 45
- Τοποθέτηση ή αφαίρεση του μάλλινου καλύμματος προαιρετικό εξάρτημα 45
- Τοποθέτηση ή αφαίρεση του μάλλινου πέλματος προαιρετικό εξάρτημα εικ 8 45
- Τοποθέτηση πλάγιας λαβής 45
- Τοποθέτηση πλάγιας χειρολαβής λαβή προαιρετικό εξάρτημα εικ 12 45
- Δήλωση συμμόρφωσης εκ 46
- Προαιρετικα εξαρτηματα 46
- Genel elektrikli alet güvenliği 47
- Genel görünüşün açıklanması 47
- Polisaj maki nesi güvenli k uyarilari 47
- Türkç 47
- Özelli kler 47
- Anahtar işlemi şek 2 48
- Bu tali matlari saklayin 48
- I şlevsel açiklamalar 48
- Şaft kilidi şek 1 48
- Destekleme yastığı ile donatılmış aletler için 49
- Hız ayar kadranı şek 3 49
- Kauçuk yastık ile donatılmış aletler için 49
- Koruyucu kapağın çıkarılması veya takılması şek 4 49
- Kullanim 49
- Montaj 49
- Polisaj işlemi şek 13 49
- Yan kavrama tutamak kolunun takılması isteğe bağlı aksesuar şek 12 49
- Yün bonenin takılması veya çıkarılması isteğe bağlı aksesuar 49
- Yün yastığın takılması veya çıkarılması isteğe bağlı aksesuar şek 8 49
- Çember kol takılması 49
- Ec uygunluk beyanı 50
- I steğe bağli aksesuarlar 50
- Karbon fırçaların değiştirilmesi şek 15 ve 16 50
- Toz kapağının temizlenmesi şek 14 50
Похожие устройства
- Makita 9069f Инструкция по эксплуатации
- Makita 9558hnk Инструкция по эксплуатации
- Makita 9741 Инструкция по эксплуатации
- Makita bo5031 Инструкция по эксплуатации
- Makita 9562ch Инструкция по эксплуатации
- Motorola FX7500 Инструкция по эксплуатации
- Motorola FX7400 Инструкция по эксплуатации
- Makita ga9030sf01 Инструкция по эксплуатации
- Makita ga9040sf01 Инструкция по эксплуатации
- ШТРИХ–М ШТРИХ-КОПИ V.1.6 Инструкция по эксплуатации
- Cat Eye INOU (MSC-GC100) Инструкция по эксплуатации
- Cat Eye Q3a (MSC-CY300) Инструкция по эксплуатации
- Cat Eye Q3 (MSC-CY200) Инструкция по эксплуатации
- Cat Eye STEALTH EVO PLUS (CC-GL51) Инструкция по эксплуатации
- Cat Eye STRADA SMART GPS (CC-RD500B) Инструкция по эксплуатации
- Cat Eye V3n (CC-TR310TW) Инструкция по эксплуатации
- Cat Eye CC-CD200DW Инструкция по эксплуатации
- Cat Eye CC-CD300DW (CC-CD300DW) Инструкция по эксплуатации
- Cat Eye STEALTH 50 (CC-GL 50) Инструкция по эксплуатации
- Cat Eye STRADA DIGITAL WIRELESS (CC-RD430DW) Инструкция по эксплуатации