![Makita 4351FCT [10/32] Bevel cutting](/img/pdf.png)
Makita 4351FCT [10/32] Bevel cutting
10
To install the blade, open the tool opener to the position
shown in the figure. (Fig. 4)
Keeping that situation, insert the saw blade into the blade
clamp as far as the two protrusions of the blade can not
be seen. (Fig. 5)
Return the tool opener to its original position.
After installing, always make sure that the blade is
securely held in place by trying to pull it out.
CAUTION:
• Do not open the tool opener excessively, or it may
cause tool damage.
To remove the blade, open the tool opener to the position
shown in the figure. Pull the saw blade out toward the
base. (Fig. 6)
NOTE:
• Occasionally lubricate the roller.
Hex wrench storage (Fig. 7)
When not in use, the hex wrench can be conveniently
stored.
OPERATION
CAUTION:
• Hold the tool firmly with one hand on the switch handle
and the other hand on the front grip when performing
the tool.
• Always hold the tool base flush with the workpiece.
Failure to do so may cause blade breakage, resulting in
a serious injury.
Turn the tool on and wait until the blade attains full speed.
Then rest the tool base flat on the workpiece and gently
move the tool forward along the previously marked cut-
ting line. When cutting curves, advance the tool very
slowly. (Fig. 8)
Bevel cutting
CAUTION:
• Always be sure that the tool is switched off and
unplugged before tilting the tool base.
With the tool base tilted, you can make bevel cuts at any
angle between 0° and 45° (left or right). (Fig. 9)
Loosen the bolt on the back of the base with the hex
wrench. Move the base so that the bolt is positioned in
the center of the bevel slot in the base. (Fig. 10)
Tilt the base until the desired bevel angle is obtained.
The V-notch of the gear housing indicates the bevel
angle by graduations. Then tighten the bolt firmly to
secure the base. (Fig. 11)
Front flush cuts (Fig. 12)
Loosen the bolt on the back of the tool base with the hex
wrench, and slide the base all the way back. Then tighten
the bolt to secure the tool base.
Cutouts
Cutouts can be made with either of two methods A or B.
A) Boring a starting hole:
For internal cutouts without a lead-in cut from an
edge, pre-drill a starting hole 12 mm or more in diam-
eter. Insert the blade into this hole to start your cut.
(Fig. 13)
B) Plunge cutting:
You need not bore a starting hole or make a lead-in
cut if you carefully do as follows.
1. Tilt the tool up on the front edge of the base with
the blade point positioned just above the work-
piece surface. (Fig. 14)
2. Apply pressure to the tool so that the front edge of
the base will not move when you switch on the tool
and gently lower the back end of the tool slowly.
3. As the blade pierces the workpiece, slowly lower
the base of the tool down onto the workpiece sur-
face.
4. Complete the cut in the normal manner.
Finishing edges (Fig. 15)
To trim edges or make dimensional adjustments, run the
blade lightly along the cut edges.
Metal cutting
Always use a suitable coolant (cutting oil) when cutting
metal. Failure to do so will cause significant blade wear.
The underside of the workpiece can be greased instead
of using a coolant.
Dust extraction
The dust nozzle (accessory) is recommended to perform
clean cutting operations.
To attach the dust nozzle on the tool, insert the hook of
dust nozzle into the hole in the base. (Fig. 16 & 17)
The dust nozzle can be installed on either left or right
side of the base.
Then connect a Makita vacuum cleaner to the dust noz-
zle. (Fig. 18)
CAUTION:
• If you try to remove the dust nozzle forcibly, the hook of
the dust nozzle can be diminished and removed unin-
tentionally during operation.
Rip fence set (optional accessory)
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing accessories.
1) Straight cuts (Fig. 19 & 20)
When repeatedly cutting widths of 160 mm or less,
use of the rip fence will assure fast, clean, straight
cuts. To install, insert the rip fence into the rectangular
hole on the side of the tool base with the fence guide
facing down. Slide the rip fence to the desired cutting
width position, then tighten the bolt to secure it.
2) Circular cuts (Fig. 21 & 22)
When cutting circles or arcs of 170 mm or less in
radius, install the rip fence as follows.
Insert the rip fence into the rectangular hole on the
side of the tool base with the fence guide facing up.
Insert the circular guide pin through either of the two
holes on the fence guide. Screw the threaded knob
onto the pin to secure the pin.
Now slide the rip fence to the desired cutting radius,
and tighten the bolt to secure it in place. Then move
the tool base all the way forward.
NOTE:
• Always use blades No. B-17, B-18, B-26 or B-27
when cutting circles or arcs.
Содержание
- Символы p.6
- Symbole p.6
- Symbols p.6
- English p.7
- Specifications p.7
- Save these instructions p.7
- General safety rules p.7
- Explanation of general view p.7
- Use clamps or another practical way to secure and support the workpiece to a stable platform p.8
- Warning misuse or failure to follow the safety rules stated in this instruction manual may cause serious personal injury p.8
- Specific safety rules p.8
- Save these instructions p.8
- Do not let comfort or familiarity with product gained from repeated use replace strict adher ence to jig saw safety rules if you use this tool unsafely or incorrectly you can suffer serious personal injury 1 hold power tools by insulated gripping sur faces when performing an operation where the cutting tool may contact hidden wiring or its own cord p.8
- Always use safety glasses or goggles ordi nary eye or sun glasses are not safety glasses 4 avoid cutting nails inspect workpiece for any nails and remove them before operation 5 do not cut oversize workpiece 6 check for the proper clearance beyond the workpiece before cutting so that the blade will not strike the floor workbench etc 7 hold the tool firmly 8 make sure the blade is not contacting the workpiece before the switch is turned on 9 keep hands away from moving parts 10 do not leave the tool running operate the tool only when hand held 11 always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece 12 do not touch the blade or the workpiece immediately after operation they may be extremely hot and could burn your skin 13 do not operate the tool at no load unneces sarily 14 some material contains chemicals which may be toxic take caution to prevent dust inhala tion and skin contact follow material sup plier safety data 15 always p.8
- For 4351fct only p.9
- Assembly p.9
- Switch action fig 2 p.9
- Speed adjusting dial fig 3 p.9
- Selecting the cutting action fig 1 p.9
- Lighting up the lamps p.9
- Installing or removing saw blade fig 4 5 6 p.9
- Functional description p.9
- Rip fence set optional accessory p.10
- Operation p.10
- Metal cutting p.10
- Hex wrench storage fig 7 p.10
- Front flush cuts fig 12 p.10
- Finishing edges fig 15 p.10
- Dust extraction p.10
- Cutouts p.10
- Circular cuts fig 21 22 p.10
- Bevel cutting p.10
- Straight cuts fig 19 20 p.10
- Maintenance p.11
- Guide rail adapter set accessory p.11
- For model 4351t p.11
- For model 4351ct 4351fct p.11
- For european countries only p.11
- Ec declaration of conformity p.11
- Ct 4351fct p.11
- Cover plate fig 26 p.11
- Ce 2006 p.11
- Anti splintering device fig 27 p.11
- Accessories p.11
- Technische daten p.12
- Diese anweisungen aufbewahren p.12
- Deutsch p.12
- Allgemeine sicherheitsregeln p.12
- Übersicht p.12
- Spezielle sicherheitsregeln p.13
- Wahl der schnittbewegung abb 1 p.14
- Schalterfunktion abb 2 p.14
- Hubzahl stellrad abb 3 p.14
- Funktionsbeschreibung p.14
- Bewahren sie diese hinweise sorgfältig auf p.14
- Randnahe schnitte abb 12 p.15
- Montage demontage des sägeblatts abb 4 5 u 6 p.15
- Montage p.15
- Inbusschlüssel aufbewahrung abb 7 p.15
- Gehrungsschnitte p.15
- Einschalten der lampen p.15
- Betrieb p.15
- Ausschnitte p.15
- Bearbeitung von kanten abb 15 p.16
- Wartung p.16
- Staubabsaugung p.16
- Schneiden von metall p.16
- Parallelanschlagsatz sonderzubehör p.16
- Führungsanschlagsatz zubehör p.16
- Zubehör p.17
- Nur für europäische länder p.17
- Ce konformitätserklärung p.17
- Ce 2006 p.17
- Zachowaj tę instrukcję p.18
- Wyjaśnienia dotyczące urządzenia i jego użycia p.18
- Polski p.18
- Ogólne zasady bezpieczeństwa p.18
- Dane techniczne p.18
- Szczegółowe zasady bezpieczeństwa p.19
- Działanie włącznika rys 2 p.20
- Zawsze używaj maski przeciwpyłowej respiratora właściwego dla obrabianego materiału i wykonywanej pracy p.20
- Zachowaj tę instrukcję p.20
- Wybór sposobu cięcia rys 1 p.20
- Pokrętło regulacji prędkości rys 3 p.20
- Opis działania p.20
- Zapalanie lampek p.21
- Zakładanie lub wyjmowanie brzeszczotu rys 4 5 i 6 p.21
- Wycięcia p.21
- Składanie p.21
- Przechowywanie klucza sześciokątnego rys 7 p.21
- Postępowanie p.21
- Cięcie ukośne p.21
- Urządzenie antyodpryskowe rys 27 p.22
- Płyta ochronna rys 26 p.22
- Konserwacja p.22
- Cięcie metalu p.22
- Zestaw prowadnicy wyposażenie dodatkowe p.22
- Zestaw adaptora prowadnicy wyposażenie p.22
- Wykańczanie brzegów rys 5 p.22
- Wyposażenie p.23
- Ue deklaracja zgodności p.23
- Tylko dla krajów europejskich p.23
- Szummy p.23
- Model 4351t p.23
- Model 4351ct 4351fct p.23
- Drgania p.23
- Ce 2006 p.23
- Русский язык p.24
- Технические характеристики p.24
- Сохраните эту инструкцию p.24
- Общие правила безопасности p.24
- Алюмини p.24
- Описание функционирования p.26
- Сохраните эти инструкции p.26
- Особые правила безопасности p.26
- Установка или удаление лезвия пилы рис 4 5 и 6 p.27
- Сборка p.27
- Регулятор переключения скорости рис 3 p.27
- Действия при переключении рис 2 p.27
- Высвечивание ламп p.27
- Эксплуатация p.28
- Хранение торцевого гаечного ключа рис 7 p.28
- Резка металла p.28
- Передние разрезы вровень рис 12 p.28
- Отделка краев рис 15 p.28
- Наклонная резка p.28
- Извлечение пыли p.28
- Вырезание p.28
- Установка направляющей планки дополнительная принадлежность p.29
- Стыковочная накладка рис 26 p.29
- Противорасщепляющее устройство рис 27 p.29
- Принадлежности p.29
- Набор направляющего держателя принадлежность p.29
- Ехническое обслуживание p.29
- Модель 4351t p.30
- Модель 4351ct 4351fct p.30
- Ес декларация соответствия p.30
- Ce 2006 p.30
Похожие устройства
-
Makita 4329Инструкция по применению -
Makita 4328Инструкция по применению
-
Makita 4327Руководство пользователя
-
Makita 4326Руководство по работе с устройством
-
Makita 4329Руководство по эксплуатации -
Makita 4326Инструкция по эксплуатации -
Makita 4326Инструкция по эксплуатации -
Makita 4327Инструкция по эксплуатации
-
Makita 4329Инструкция по эксплуатации
-
Makita 4350CTИнструкция по эксплуатации -
Makita 4351CTИнструкция по эксплуатации -
Makita 4350FCT, 720 ВтИнструкция по эксплуатации