![Makita HP1641F [5/36] Assembly](/img/pdf.png)
Makita HP1641F [5/36] Assembly
![Makita HP1641F [5/36] Assembly](/views2/1175435/page5/bg5.png)
5
Lighting up the lamps (Fig. 2)
For Model HP1640F, HP1641F
CAUTION:
• Do not look in the light or see the source of light
directly.
To turn on the lamp, pull the trigger. Release the trigger
to turn it off.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower
the illumination.
• Never use gasoline or thinner to clean the lens of the
lamp, or it will be damaged.
Reversing switch action (Fig. 3)
This tool has a reversing switch to change the direction of
rotation. Move the reversing switch to the position (A
side) for clockwise rotation or the position (B side) for
counterclockwise rotation.
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• If the switch trigger can not be depressed, check to see
that the reversing switch is fully set to position (A
side) or (B side).
Selecting the action mode (Fig. 4)
This tool has an action mode change lever. For rotation
with hammering, slide the action mode change lever to
the right (
g symbol). For rotation only, slide the action
mode change lever to the left (
m symbol).
CAUTION:
• Always slide the action mode change lever all the way
to your desired mode position. If you operate the tool
with the lever positioned halfway between the mode
symbols, the tool may be damaged.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing side grip (auxiliary handle) (Fig. 5)
Always use the side grip to ensure operating safety.
Install the side grip on tool barrel.
Then tighten the grip by turning clockwise at the desired
position. It may be swung 360° so as to be secured at
any position.
NOTE:
• The side grip cannot swing 360° when the depth gauge
is installed.
Installing or removing drill bit
For Model HP1640, HP1640F (Fig. 6)
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. Be sure to
tighten all three chuck holes evenly.
To remove the bit, turn the chuck key counterclockwise in
just one hole, then loosen the chuck by hand.
After using the chuck key, be sure to return to the original
position.
For Model HP1641, HP1641F (Fig. 7)
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as it
will go. Hold the ring firmly and turn the sleeve clockwise
to tighten the chuck.
To remove the bit, hold the ring and turn the sleeve coun-
terclockwise.
Depth gauge (Fig. 8)
The depth gauge is convenient for drilling holes of uni-
form depth. Loosen the side grip and insert the depth
gauge into the hole in the side grip. Adjust the depth
gauge to the desired depth and tighten the side grip.
NOTE:
• The depth gauge cannot be used at the position where
the depth gauge strikes against the tool body.
OPERATION
Hammer drilling operation (Fig. 9)
CAUTION:
• There is a tremendous and sudden twisting force
exerted on the tool/bit at the time of hole break-
through, when the hole becomes clogged with chips
and particles, or when striking reinforcing rods embed-
ded in the concrete. Always use the side grip (auxiliary
handle) and firmly hold the tool by both side grip and
switch handle during operations. Failure to do so may
result in the loss of control of the tool and potentially
severe injury.
When drilling in concrete, granite, tile, etc., move the
action mode changing lever to the position of
g symbol
to use “rotation with hammering” action.
Be sure to use a tungsten-carbide tipped bit.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light pres-
sure gives best results. Keep the tool in position and pre-
vent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at an
idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
Blow-out bulb (optional accessory) (Fig. 10)
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
Drilling operation
When drilling in wood, metal or plastic materials, move
the action mode changing lever to the position of
m sym-
bol to use “rotation only” action.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the bit into the
workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole,
make an indentation with a center-punch and hammer at
the point to be drilled. Place the point of the bit in the
indentation and start drilling.
Use a cutting lubricant when drilling metals. The excep-
tions are iron and brass which should be drilled dry.
Содержание
- Gr κρ υστικ τρυπάνι δηγίες ρήσεως 1
- Hp1640 hp1640f hp1641 hp1641f 1
- English 4
- Explanation of general view 4
- Functional description 4
- Hammer drill safety warnings 4
- Save these instructions 4
- Specifications 4
- Switch action fig 1 4
- Assembly 5
- Blow out bulb optional accessory fig 10 5
- Depth gauge fig 8 5
- Drilling operation 5
- Hammer drilling operation fig 9 5
- Installing or removing drill bit 5
- Installing side grip auxiliary handle fig 5 5
- Lighting up the lamps fig 2 5
- Operation 5
- Reversing switch action fig 3 5
- Selecting the action mode fig 4 5
- Accessories 6
- Maintenance 6
- Conservez ces instructions 7
- Consignes de sécurité pour la perceuse à percussion 7
- Descriptif 7
- Français 7
- Spécifications 7
- Allumage de la lampe fig 2 8
- Assemblage 8
- Description du fonctionnement 8
- Gabarit de profondeur fig 8 8
- Installation de la poignée latérale poignée auxiliaire fig 5 8
- Installation ou retrait du foret 8
- Interrupteur fig 1 8
- Inverseur fig 3 8
- Sélection du mode de fonctionnement fig 4 8
- Accessoires 9
- Entretien 9
- Perçage 9
- Perçage avec martelage fig 9 9
- Poire soufflante accessoire en option fig 10 9
- Utilisation 9
- Bewahren sie diese hinweise sorgfältig auf 10
- Deutsch 10
- Für schlagbohrmaschine sicherheitswarnungen 10
- Technische daten 10
- Übersicht 10
- Drehrichtungsumschalterbedienung abb 3 11
- Ein und ausschalten der lampen abb 2 11
- Funktionsbeschreibung 11
- Montage 11
- Montage und demontage des bohrers 11
- Montieren des seitengriffs zusatzgriffs abb 5 11
- Schalterfunktion abb 1 11
- Tiefenanschlag abb 8 11
- Wahl der betriebsart abb 4 11
- Ausblaspipette sonderzubehör abb 10 12
- Betrieb 12
- Bohren 12
- Schlagbohren abb 9 12
- Wartung 12
- Zubehör 12
- Avvertimenti per la sicurezza trapano a percussione 13
- Conservate queste istruzioni 13
- Dati tecnici 13
- Italiano 13
- Visione generale 13
- Accensione delle lampadine fig 2 14
- Descrizione del funzionamento 14
- Funzionamento dell interruttore di inversione fig 3 14
- Funzionamento dell interruttore fig 1 14
- Installazione dell impugnatura laterale manico ausiliario fig 5 14
- Installazione o rimozione della punta trapano 14
- Montaggio 14
- Selezione della modalità di funzionamento fig 4 14
- Spessimetro fig 8 14
- Accessori 15
- Funzionamento 15
- Manutenzione 15
- Operazione di foratura 15
- Operazione di foratura con percussione fig 9 15
- Soffietto accessorio opzionale fig 10 15
- Bewaar deze voorschriften 16
- Nederlands 16
- Technische gegevens 16
- Veiligheidswaarschuwingen voor hamerboor 16
- Verklaring van algemene gegevens 16
- Beschrijving van de functies 17
- De lamp aanzetten fig 2 17
- Dieptemaat fig 8 17
- Ineenzetten 17
- Installeren of verwijderen van de boor 17
- Installeren van de zijhandgreep hulphandgreep fig 5 17
- Kiezen van de gewenste werking fig 4 17
- Werking van de omkeerschakelaar fig 3 17
- Werking van de trekschakelaar fig 1 17
- Accessoires 18
- Bediening 18
- Blaasbalgje los verkrijgbaar accessoire fig 10 18
- Hamerend boren fig 9 18
- Onderhoud 18
- Advertencias de seguridad para el taladro de percusión 19
- Español 19
- Especificaciones 19
- Explicación de los dibujos 19
- Guarde estas instrucciones 19
- Accionamiento del interruptor de inversión fig 3 20
- Accionamiento del interruptor fig 1 20
- Descripción funcional 20
- Iluminación de las lámparas fig 2 20
- Instalación de la empuñadura lateral mango auxiliar fig 5 20
- Instalación o desmontaje de la broca 20
- Montaje 20
- Selección del modo de accionamiento fig 4 20
- Tope de profundidad fig 8 20
- Accesorios 21
- Mantenimiento 21
- Operación 21
- Operación de taladrado 21
- Operación de taladrado con percusión fig 9 21
- Soplador accesorio opcional fig 10 21
- Avisos de segurança para o berbequim de percussão 22
- Especificações 22
- Explicação geral 22
- Guarde estas instruções 22
- Português 22
- Acender as lâmpadas fig 2 23
- Acção do interruptor de inversão fig 3 23
- Acção do interruptor fig 1 23
- Assemblagem 23
- Descrição funcional 23
- Guia de profundidade fig 8 23
- Instalar ou retirar a broca de perfurar 23
- Instalação do punho lateral pega auxiliar fig 5 23
- Operação 23
- Operação de perfuração com martelo fig 9 23
- Selecção do modo de acção fig 4 23
- Acessórios 24
- Manutenção 24
- Operação de perfuração 24
- Soprador acessório opcional fig 10 24
- Gem disse forskrifter 25
- Illustrationsoversigt 25
- Sikkerhedsforskrifter for borehammer 25
- Specifikationer 25
- Afbryderbetjening fig 1 26
- Betjening 26
- Dybdeanslag fig 8 26
- Funktionsbeskrivelse 26
- Hammerboring fig 9 26
- Montering af sidegreb ekstrahåndtag fig 5 26
- Montering og afmontering af bor 26
- Omdrejningsvælgerbetjening fig 3 26
- Samling 26
- Tænd af lamperne fig 2 26
- Valg af funktion fig 4 26
- Boring 27
- Tilbehør 27
- Udblæsningskugle ekstraudstyr fig 10 27
- Vedligholdelse 27
- Ελληνικα 28
- Κρ υστικ τρυπανι πρ ει π ιησεισ ασφαλειασ 28
- Περιγραφή γενικής άπ ψης 28
- Τε νικα αρακτηριστικα 28
- Φυλα ετε αυτεσ τισ ηγιεσ 28
- Αναµµα λαµπών εικ 2 29
- Επιλ γή τρ π υ λειτ υργίας εικ 4 29
- Λειτ υργία διακ πτη αντιστρ φής εικ 3 29
- Περιγραφη λειτ υργιασ 29
- Ράση διακ πτη εικ 1 29
- Συναρμ λ γηση 29
- Τ π θέτηση ή αφαίρεση αι µής τρυπανι ύ 29
- Τ π θέτηση πλάγιας λα ής ηθητική λα ή εικ 5 29
- Κεφαλή φυσητήρα πρ αιρετικ ε άρτηµα εικ 10 30
- Λειτ υργία κρ υστικ ύ τρυπανίσµατ ς εικ 9 30
- Λειτ υργία τρυπανίσµατ ς 30
- Λειτ υργια 30
- Μετρητής άθ υς εικ 8 30
- Συντηρηση 30
- Ε αρτηματα 31
- Deutsch 32
- Dichiarazione ce di conformità 32
- Déclaration de conformité ce 32
- Ec declaration of conformity 32
- Eg übereinstimmungserklärung 32
- English 32
- Française 32
- Italiano 32
- Declaración de conformidad ce 33
- Declaração de conformidade ce 33
- Español 33
- Eu konformitetserklæring 33
- Eu verklaring van conformiteit 33
- Nederlands 33
- Português 33
- Ήλωση συµµ ρφωσης εκ 34
- Ελληνικα 34
- Deutsch 35
- English 35
- Español 35
- Française 35
- Italiano 35
- Nederlands 35
- Anjo aichi japan 36
- Makita corporation 36
- Português 36
- Ελληνικα 36
Похожие устройства
- Makita HP1640 Инструкция по эксплуатации
- Makita HP1640K Инструкция по эксплуатации
- Makita 6347DWAE Инструкция по эксплуатации
- Makita DF330DWLE Инструкция по эксплуатации
- Makita 6337DWDE Инструкция по эксплуатации
- Makita 6337DWAE Инструкция по эксплуатации
- Makita 6281DWPLE Инструкция по эксплуатации
- Makita 8281DWPE Инструкция по эксплуатации
- Makita 6281DWPE Инструкция по эксплуатации
- Makita 6271DWPE Инструкция по эксплуатации
- Makita 6271DWALE Инструкция по эксплуатации
- Makita 6271DWAE Инструкция по эксплуатации
- Makita 6261DWPE Инструкция по эксплуатации
- Perfeo PF-168-3-OUT Инструкция по эксплуатации
- Maman fdir-v1 Инструкция по эксплуатации
- Perfeo PF-168-3-IN Инструкция по эксплуатации
- Perfeo PF-168-1-OUT Инструкция по эксплуатации
- Marta mt-1963, 5 л, 900 вт Инструкция по эксплуатации
- Perfeo PF-168-1-IN Инструкция по эксплуатации
- ТРИД РП-550 Инструкция по эксплуатации