Graco CycleFlo [4/18] Warning
![Graco CycleFlo [4/18] Warning](/views2/1193691/page4/bg4.png)
4 309003
WARNING
FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD
Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition
and result in fire or explosion and other serious injury.
D Ground the pumping equipment. Proper grounding dissipates static electricity.
D This equipment is not intended for intrinsically safe areas.
D Keep the dispense area free of debris, including solvent, rags, and gasoline.
D If there is any static sparking or you feel an electric shock while using the equipment, stop op-
erating immediately. Do not use the equipment until you have identified and corrected the
problem.
D Make sure all electrical work is performed by a qualified electrician.
D Have any checks, installation, or service to electrical equipment performed by a qualified electri-
cian only.
D Make sure all electrical equipment is installed and operated in compliance with local and appli-
cable codes.
D Make sure power is disconnected when servicing and repairing equipment.
D Keep liquids away from the electrical components.
D Disconnect electrical power at the main switch before servicing equipment.
D Never exceed maximum wattage of the supply unit.
Содержание
- Controls pump speed run time and quantity of product delivered for precise batching metering and dosing of fluids at high or low pressures and flow rates 1
- Cycleflo pneumatic pump controller 1
- Instructions parts list 1
- Not for use in explosive atmospheres 1
- Part no 195264 1
- Table of contents 2
- Caution 3
- Caution symbol 3
- Equipment misuse hazard 3
- Symbols 3
- Warning 3
- Warning symbol 3
- Fire explosion and electric shock hazard 4
- Warning 4
- General description 5
- Electrical connections 6
- Installation 6
- Pneumatic connections 6
- Warning 6
- Dip switch sw1 7
- Installation 7
- Microprocessor 7
- Power supply 7
- 40 35 30 8
- Cpm 10 15 8
- Cycles per minute cpm rate 8
- Presets 8
- Setup and programming 8
- Sw1 cpm rate table 8
- Front panel operation 9
- Operation 9
- Priming the pump 9
- Remote operation 9
- Troubleshooting 10
- Caution 11
- Self test mode 11
- Cycleflo controller 13
- Typical installation diagrams 13
- 309003 14
- Chemical injector 14
- Cycleflo controller 14
- Provided by others 14
- Typical installation diagrams 14
- Cycleflo controller 15
- Sends on off signal to cycleflo controller 15
- Typical installation diagrams 15
- Water neutralization 15
- 309003 16
- Cycleflo controller 16
- Provided by others 16
- Typical installation diagrams 16
- Water treatment 16
- Mounting information 17
- Specifications 17
- 309003 18
- Copyright 1999 graco inc all graco manufacturing locations are registered to iso 9001 www graco com 18
- For the latest information about graco products visit www graco com 18
- Graco information 18
- Graco standard warranty 18
- To place an order contact your graco distributor or call to identify the distributor closest to you phone 612 623 6921 or toll free 1 800 328 0211 fax 612 378 3505 18
Похожие устройства
- Graco CycleFlo II Инструкция по эксплуатации
- Graco Твердотельный таймер Инструкция по эксплуатации
- Graco FieldLazer S100 Инструкция по эксплуатации
- Graco FieldLazer S100 Брошюра
- Graco FieldLazer S90 Инструкция по эксплуатации
- Graco FieldLazer S90 Брошюра
- Graco LineLazer V 200HS Инструкция по эксплуатации
- Graco LineLazer V 200HS Брошюра
- Graco LineLazer V 3900 Инструкция по эксплуатации
- Graco LineLazer V 3900 Брошюра
- Graco LineLazer V 5900 Инструкция по эксплуатации
- Graco LineLazer V 5900 Брошюра
- Graco RMLS-5 Инструкция по эксплуатации
- Graco RMLS-50 Инструкция по эксплуатации
- Graco EMLS-5 Инструкция по эксплуатации
- Graco Manzel GBL 7500 Инструкция по эксплуатации
- Graco 24F531 Инструкция по эксплуатации
- Graco 24F531 Брошюра
- Graco 24F878 Инструкция по эксплуатации
- Graco 24F878 Технические характеристики