![Graco InvisiPac HM25 [6/14] Installation](/img/pdf.png)
Graco InvisiPac HM25 [6/14] Installation
![Graco InvisiPac HM25 [6/14] Installation](/views2/1193784/page6/bg6.png)
Installation
6 332072M
Installation
NOTE: Pressure check the hose assemblies. Refer to
your system operation manual for priming and pressur
izing the fluid hoses. Check carefully for leaks at the
hose connections. If there are leaks, relieve the pres
sure as instructed on page 8. Tighten all hose connec
tions and check for leaks by pressurizing the system.
NOTE: InvisiPac hose diameter may be larger than pre
viously installed hose. Verify all items used during instal
lation, including any re-used items such as hose
supports, mounts, and hose routings, meet all of the fol
lowing requirements.
1. Do not use hose to pull the equipment.
2. Use 2 wrenches to tighten. Torque to specification:
3. Do not tape or cover hose.
4. Do not flex hose when cold.
5. Use hose support spring.
6. Do not clamp, squeeze, or zip tie hose.
7. Minimum bend radius:
To reduce the risk of skin injection, follow the Pres
sure Relief Procedure on page 8 whenever you are
instructed to relieve pressure.
To reduce the risk of electric shock, do not allow
Standard hoses to come into contact with liquids of
any kind. Only use Water-wash hoses with
Water-wash cord sets and valves.
Torque
Fitting in-lb (N•m)
-6 300 (33.9)
Fitting
Radius
in. (mm)
-6 8 (203)
Содержание
- Heated hose 1
- Instructions parts 1
- Invisipa 1
- War war war warning 1
- 332072m 2
- Contents 2
- Parts 12 heated hose instruction tag 120051 12 heated hose warning label 196694 12 water wash heated hose instruction tag 17a202 12 accessories 12 self sealing silicone rubber tape 16y938 12 yd 11 m roll 12 hose hanger spring kit 253283 12 technical data 13 graco standard warranty 14 graco information 14 2
- Standard model hoses 2
- Standard model hoses 2 water wash model hoses 2 warnings 3 overview 5 installation 6 pressure relief procedure 8 operation 8 maintenance 9 washing instructions 9 troubleshooting 10 2
- Standard model hoses are meant for dry environments only standard model hoses have a gray braided scuff guard 2
- Water wash model hoses 2
- Water wash model hoses are meant for wash down environments water wash models have a black rubber scruff guard water wash hoses are ipx6 rated 2
- Warning 3
- Warnings 3
- Warning 4
- Overview 5
- Installation 6
- Operation 8
- Pressure relief procedure 8
- Maintenance 9
- Washing instructions 9
- Washing instructions water wash hoses only 9
- A use an ohmmeter to check the electrical resis tance at the heating element pins between pins c and d of the melter end connector that attaches to the heated hose control see 10
- Any resistance reading outside the range indicates that the hose must be replaced 10
- Approximate rtd resistance values at various tempera tures 10
- Between pins m and k of the large melter end con nector the rtd resistance must be within the range of the following chart 10
- Check all hose connections to be sure they are securely tightened 10
- Check the continuity of the hose components to verify proper resistance of the heater cable 10
- Ground the system see system manual for instruc tions 10
- Lack of electrical continuity between any of these pins indicates the hose must be replaced 10
- Make sure there is electrical continuity 10 ώ between the following pins of the large melter end con nector and the small gun end connector 10
- The resis tance of the heating element for the various lengths of coupled hose assemblies is given in the following coupled hose chart 10
- The resistance values of the rtd will vary with tempera ture an approximation of hose temperature must be made to verify the resistance reading of the rtd across pin m and k is correct 10
- Troubleshooting 10
- Continuity between connectors 11
- Gnd gnd 11
- Melter end gun end 11
- Troubleshooting 11
- Accessories 12
- Heated hose instruction tag 120051 12
- Heated hose warning label 196694 12
- Hose hanger spring kit 253283 12
- Self sealing silicone rubber tape 16y938 12 yd 11 m roll 12
- Water wash heated hose instruction tag 17a202 12
- Technical data 13
- Copyright 2012 graco inc all graco manufacturing locations are registered to iso 9001 www graco com revision m may 2016 14
- For patent information see www graco com patents 14
- For the latest information about graco products visit www graco com 14
- Graco headquarters minneapolis international offices belgium china japan korea 14
- Graco inc and subsidiaries p o box 1441 minneapolis mn 55440 1441 usa 14
- Graco information 14
- Graco standard warranty 14
- Original instructions this manual contains english mm 332072 14
- To place an order contact your graco distributor or call to identify the nearest distributor phone 612 623 6921 or toll free 1 800 328 0211 fax 612 378 3505 14
Похожие устройства
- Graco InvisiPac HM50 Инструкция по эксплуатации
- Graco InvisiPac HM50 Технические характеристики
- Graco InvisiPac HM50 Руководство пользователя
- Graco Reactor H-25 Инструкция по эксплуатации
- Graco Reactor H-25 Брошюра
- Graco Reactor H-40 Инструкция по эксплуатации
- Graco Reactor H-40 Технические характеристики
- Graco Reactor H-50 Инструкция по эксплуатации
- Graco Reactor H-50 Технические характеристики
- Graco Reactor H-XP2 Инструкция по эксплуатации
- Graco Reactor H-XP2 Технические характеристики
- Graco Reactor H-XP3 Инструкция по эксплуатации
- Graco Reactor H-XP3 Технические характеристики
- Graco Reactor H-VR Инструкция по эксплуатации
- Graco Reactor H-VR Технические характеристики
- Graco Reactor E-10 Инструкция по эксплуатации
- Graco Reactor E-10 Технические характеристики
- Graco Reactor 2 H-30 Инструкция по эксплуатации
- Graco Reactor 2 H-30 Брошюра
- Graco Reactor 2 Elite H-30 Инструкция по эксплуатации