![Supermicro sys-6028r-tr Инструкция по эксплуатации онлайн [48/73] 187894](/icons/site-icon-64.png){kind=icon}
Supermicro sys-6028r-tr Инструкция по эксплуатации онлайн [48/73] 187894
Превью страниц
Страница 48 /
73
![Supermicro sys-6028r-tr Инструкция по эксплуатации онлайн [48/73] 187894](/views2/1225209/page48/bg30.png)
Содержание
387- Chapter 3 system interface
- Chapter 2 server installation
- About this manual
- Refer here for details on the system interface which includes the functions and information provided by the control panel on the chassis as well as other leds located throughout the system
- Printed in the united states of america
- Preface
- Manual revision 1 b release date april 5 2016
- Manual organization
- Chapter 4 standardized warning statements
- Chapter 1 introduction
- You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the superserver 6028r tr trt
- Warning handling of lead solder materials used in this product may expose you to lead a chemical known to the state of california to cause birth defects and other repro ductive harm
- This manual is written for professional system integrators and pc technicians it provides information for the installation and use of the superserver 6028r tr trt installation and maintainance should be performed by experienced technicians only
- This chapter describes the steps necessary to install the superserver 6028r tr trt into a rack and check out the server configuration prior to powering up the system if your server was ordered without processor and memory components this chapter will refer you to the appropriate sections of the manual for their installation
- The superserver 6028r tr trt is a high end server based on the sc825tq r740lpb 2u rackmountable chassis and the x10dri x10dri t dual processor serverboard
- The first chapter provides a checklist of the main components included with the serv er system and describes the main features of the x10dri x10dri t serverboard and the sc825tq r740lpb chassis
- Table of contents
- Chapter 5 advanced serverboard setup
- Chapter 4 standardized warning statements for ac systems
- Chapter 3 system interface
- Chapter 2 server installation
- Chapter 1 introduction
- Chapter 7 bios
- Chapter 6 advanced chassis setup
- Appendix b system specifications
- Appendix a bios error beep codes
- Introduction
- Chapter 1 introduction
- Chapter 1
- 1 overview
- Pci expansion slots
- Memory
- System power
- Processors
- I o ports
- Hard drive subsystem
- Graphics controller
- Front control panel
- Cooling fans
- 3 server chassis features
- 2 serverboard features
- Front panel
- 4 contacting supermicro
- Website www supermicro com tw
- Figure 1 1 chipset system block diagram
- Website www supermicro com
- Tel 886 2 8226 3990
- Fax 886 2 8226 3992
- Tel 31 0 73 6400390
- Fax 31 0 73 6416525
- Tel 1 408 503 8000
- Fax 1 408 503 8008
- Taiwan r o c
- F no 150 jian 1st rd
- System power
- Europe
- Support supermicro nl technical support
- Erver 6028r tr trt user s manual
- Support supermicro com technical support
- Email support supermicro com tw
- San jose ca 95131 u s a
- Email sales supermicro nl general information
- S hertogenbosch the netherlands
- Email marketing supermicro com general information
- Rock ave
- Ctrl fan speed
- Rma supermicro nl customer support
- Chapter 1 introduction
- Note this is a general block diagram please see chapter 5 for details
- Asia pacific
- Het sterrenbeeld 28 5215 ml
- Address super micro computer inc
- Zhonghe dist new taipei city 235
- Headquarters
- Address super micro computer b v
- Website www supermicro nl
- Server installation
- Choosing a setup location
- Chapter 2 server installation
- Chapter 2
- 3 preparing for setup
- 2 unpacking the system
- 1 overview
- Reduced airflow
- Rack precautions
- Rack mounting considerations
- Mechanical loading
- Circuit overloading
- Ambient operating temperature
- 4 warnings and precautions
- Server precautions
- Reliable ground
- Separating the sections of the rack rails
- Installing the inner rail extension
- 4 installing the system into a rack
- Outer rack rails
- System interface
- Chapter 3 system interface
- Chapter 3
- 2 control panel buttons
- 1 overview
- Power fail
- Information led
- 4 drive carrier leds
- 3 control panel leds
- 1 about standardized warning statements
- Warning definition
- Standardized warning statements for ac systems
- Chapter 4 standardized warning statements for ac systems
- Chapter 4
- ف ك ا ىأ يكو ةلاح ف ببستت ةباصا ة ذسج زهزلا اذه ع زطخ ز ذحت ىأ لبق يأ ىلع لوعت تاذعه كنلع ىلع ي يع ةوجا لا زطاخولاب زئاوذلا ة ئابزهكلا كوة ارد ىلع ي راوولابتاس ة ئاقىلا ل ع وعىقو يأثداىح نقر مذختسا ىا بلا صىص ولا ة اه ف ز ذحت لك رىثعلل اهتوجزت
- ןונקת תורהצהאהרהז ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע היישעתה ינקת יפ לע תורהז הלבח ה וא תולאש שיו הדימב תירשפא תיזיפי יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט ורקימרפוס לש תינכט תאה םיביכר אורקל שי ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא
- يئاقول
- ىلع
- متيتلا
- لا تاداشرإ رقابيكرت ليصوت لبق ىلإ ماظنلا ةقاطلل ردصم
- אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ
- Vdc 20
- Installation instructions
- Circuit breaker
- A 250vd
- Power disconnection warning
- مصف بجي واظننا عيمج نمرداصم تقاطنا تنازإو ءابرهكنا كهس نم ةدحو دادما تقاطنا مبق ىنإ لىصىنا تيهخادنا قطانمنا نمكيهه تنازإ وأ جيبثتن ثانىكم زاهجلا
- ילמשח קותינ ינפמ הרהזא
- הרהזא למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת םיביכר
- هيبردملاو و بيكزتللادبتسا وأ ةمدخ ساهجلا اذه حمسي نأ بجي طقف هيلهؤملا هيفظىملل
- הרהזא שר דבלב ךמסומ תווצתא ףילחהל ןיקתהל יא דויצה רובע תוריש תתל וא דויצה
- Restricted area
- Equipment installation
- صيصخت ةذحىنا هذه ف اهب كرتن قطانم ةروظحم مت صىنا نكم نإ لى تقطنم ةروظحم طقف واذختسا للاخ نم تصاخ ةادأ وأ أ لان يرخأ ته سو املأم حاتفمو مفق
- رطخ كانه نم لاذبحسا ةلاح يف راجفنا ةيراطبلا ةحيحص ريغ ةقيرطب ليلعف ةيراطبلا لاذبحسا طقف عىنلا سفنب اهلداعي ام وأ اممثصوأ ةعنصملا ةمرشلا هب تايراطبلا نم صلخج ل اقفو ةلمعحسملاةعناصلا ةمرشلا تاميلعح
- תלבגומ השיג םע רוזא הרהזא תרזעב תנתינ השיגה השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי דכו לוענמ חתפמ דבלב החטבא ילכ
- הרהזא תנכס תמייקץוציפ הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ תוללוסה קוליס תושמושמה עצבל שי ןרציה תוארוה יפל
- Battery handling
- דחא קפסמ רתוי םייק םא הרהזא קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שי ןקורל תנמ לע םירוביחה לכ
- Redundant power supplies
- Backplane voltage
- 12 4 13
- دق اذهل نوكي لازاهج تلااصتا ةدع تادحوب ةقاطلا دادما ةلازإ بجي تلااصتلاا ةفاك لسعل لاةدحو نع ءابرهكلا
- חיה תאי הד
- كانه زطخ هم يئابزهكلا رايتلا ىلع ةدىجىملا ةقاطلاوأ ةحىللا نىكي امدنعماظنلا لمعي دنع ارذح هك ةمدخ ساهجلا اذه
- تادعملا بيكرت ةيئابرهكلا لل لثتمي نأ بجي هيواىقةيىطىلاو ةيلحملا ةقلعتملا ءابرهكلاب
- ירוחאה לנפב חתמ זא הרה ךלהמב רהזיהל שי תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק הדובעה
- יצראה למשחה יקוח םואית הרהזא תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה
- Product disposal
- Comply with local and national electrical codes
- 14 4 15
- يئاهنلا صلختلا نم جتنملا اذه هعم لماعتلا يغبني ل اقفو عيمجةينطىلا حئاىللاو نيناىقلا دنع
- هكممنا هم حوارمنا نأ لاست لا ةنازإ دنعرودت ةهتك ةحورمنا مكيهنا هم بجي ءاقبإ
- عباصلأا ويغاربنا تاكفم ءايشلأا هم اهريغو اديعب هع تاحتفنا يف ةهتك ةحورمنا
- רצומה קוליס הרהזא ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס הנידמה יקוח
- הרהזא יקלח תא םיריסמ רשאכ שי םידבוע ןיידע םיררוואמהו ןכתי זראמהמ ררוואמה קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ
- Hot swap fan warning
- Power cable and ac adapter
- نأ يأ ماذختسا ثلاباك ثلاىحمو يرخأ ببستي يف لطع ثوذح قيرح وأ يتلا كل اهريفىت مت جتىملا عم
- لمحت يتلاتملا
- ةسهجأ يرخأ تيئابرهك ريغ ثاجتىملا تىيعملا لبق هم يلأ
- بيكرت ذىع ماذختسا بجي زاهجلا و ليصىتلا ثلاباك تيئابرهكلا ثلاباكلا ثلاىحمو ددرتملا رايتلا
- רשא וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב שומיש ךכ םשל וקפוסו ודעונ טב יקוחו למשח ירישכמב שומיש יקוח יפ לע ילמשח רצק רוסיא םייק תוחי ב םיכמסומה םילבכב שמתשהל
- רחא ילמשח רצומ לכ רובע דבלב ורקימקרפוס ידי לע ןיוצ אלש
- לש דוק םהילע עיפומ ראשכ
- הרהזא םימאתמו םיקפס םילבכב שמתשהל שי רצומה תא םיניקתמ רשאכ
- ב וא
- אתמו םיילמשחמ י
- Ul وأ csa تيئابرهكلا ةسهجلأا داىمو نىواق تملاسلا ماذختسا رظحي ثلاباكلا لبق هم ةذمتعم
- Ul csa
- Supermicro
- Chapter 5
- Advanced serverboard setup
- 1 handling the serverboard
- Precautions
- Chapter 5 advanced serverboard setup
- Unpacking
- Connecting the control panel
- Connecting power cables
- Connecting data cables
- 3 i o ports
- 2 connecting cables
- Installing an lga2011 processor
- 4 installing the processor and heatsink
- Removing the heatsink
- Installing a cpu heatsink
- Dimm installation
- Warning exercise extreme care when installing or removing dimm modules to prevent any possible damage
- The x10dri x10dri t supports up to 1 tb of ecc lrdimm or ecc rdimm ddr4 2400 2133 1866 1600 memory use memory modules of the same type and speed see the following tables for memory installation please refer to the supermicro website for possible updates to supported memory
- Chapter 5 advanced serverboard setup
- Repeat for all modules
- Along the bottom of the module to avoid installing incorrectly see figure 5 3
- Processors and their corresponding memory modules
- 5 installing memory
- Processor memory module population configuration
- Processor and memory module population for optimal performance
- Populating rdimm lrdimm ddr4 memory modules
- P1 dimma1 when populating two dimm modules within a channel always start with bank1 first for optimal memory performance please install a pair or pairs of memory modules of the same type and speed with a maximum of 12 modules see the memory installation table below
- Memory support
- Installing memory modules
- Insert the desired number of dimms into the memory slots starting with dimm
- Insert each dimm module vertically into its slot pay attention to the notch
- Gently press down on the dimm module until it snaps into place in the slot
- For memory to work properly follow the tables below for memory installation
- Figure 5 3 dimm installation
- Erver 6028r tr trt user s manual
- X10dri t
- 7 serverboard details
- 6 adding pci add on cards
- 11 5 10
- X10dri x10dri t quick reference
- 13 5 12
- Nic2 lan2 led
- Nic1 lan1 led
- Jpwr1 and jpwr2 must also be connected to the power supply see the table on the right for pin defini tions
- To the table on the right for pin defini tions
- Hdd led
- The reset button connection is located on pins 3 and 4 of jf1 and attaches to the reset switch on the computer chassis see the table on the right for pin definitions
- Erver 6028r tr trt user s manual
- The power on connection is on pins 1 and 2 of jf1 momentarily contacting both pins will power on off the system this button can also be configured to function as a suspend button with a setting in the bios to turn off the power when the system is in suspend mode press the button for 4 seconds or longer refer to the table on the right for pin definitions
- Connect an led cable to pins 7 and 8 of front control panel to use the overheat fan fail power fail and uid led connections the red led on pin 8 provides warnings of overheat fan failure or power failure the blue led on pin 7 works as the front panel uid led indicator refer to the table on the right for pin definitions
- Chapter 5 advanced serverboard setup
- The power fail led connection is located on pins 5 and 6 of jf1 refer
- A 24 pin main power supply connector j24 and two 8 pin power connectors jpwr1 jpwr2 are provided on the serverboard these power connectors meet the ssi eps 12v specification these power connectors must be con nected to your power supply see the table on the right for pin definitions
- The led connections for lan2 are on pins 9 and 10 of jf1 attach an led cable to display network activity see the table on the right for pin definitions
- 8 connector definitions
- The led connections for lan1 are on pins 11 and 12 of jf1 attach an led cable to display network activity see the table on the right for pin definitions
- 15 5 14
- The hdd led connection is located on pins 13 and 14 of jf1 attach a cable to pin 14 to show hdd activity status attach a cable to pin 13 to use uid switch see the table on the right for pin definitions
- Secondary power connector
- Reset button
- Power fail led
- Power connectors
- Power button
- Overheat oh fan fail pwr fail uid led
- Tpm header port 80 header
- Chapter 5 advanced serverboard setup
- A trusted platform module port 80 header is located at jtpm1 to provide tpm support and port 80 connection use this header to enhance system performance and data security see
- Three sgpio serial link general purpose input output headers are located at t sgpio1 2 3 to support the sata ports see the table on the right for pin definitions
- 17 5 16
- There are eight fan headers on the serverboard fan 1 fan 6 fan a fan b all of which are 4 pin fans pins 1 3 of the fan headers are backward compatible with the traditional 3 pin fans fan speed control is supported with 4 pin fans only see the table on the right for pin definitions the fan speeds are controlled by thermal management via ipmi 2 interface
- The table on the right for pin definitions
- The power led connection is located on pins 15 and 16 of jf1 refer to the table on the right for pin definitions
- The joh1 header may be connected to an led indicator to provide warn ings of chassis overheating or fan failure refer to the table on right for pin definitions
- The internal speaker located at sp1 can be used to provide audible indica tions for various beep codes see the table on the right for pin definitions
- The chassis intrusion header is des ignated jl1 attach an appropriate cable from the chassis to inform you of a chassis intrusion when the chas sis is opened
- T sgpio1 2 t sgpio s headers
- Power led
- Overheat fan fail led
- Internal speaker
- Fan headers
- Erver 6028r tr trt user s manual
- Dom power connectors
- Two power connectors for dom disk on module devices are located at jsd1 jsd2 connect appropriate cables here to provide power support for your serial link dom devices
- Chassis intrusion
- Serial ports
- Power system management bus
- Power smb
- Power led speaker
- Pins 1 3 of jd1 are used for power led indication and pins 4 7 are for the speaker see the tables on the right for pin definitions please note that the speaker connector pins 4 7 are used with an external speaker if
- Note please refer to the led indicator section for lan led information
- Ethernet ports
- Erver 6028r tr trt user s manual
- You wish to use the onboard speaker you should close pins 6 7 with a cap
- Chapter 5 advanced serverboard setup
- Usb 2 3 ports usb12 13 are lo cated on the i o backpanel note that usb ports 12 13 support both usb 2 and 3 in addition two internal usb headers provides a total of four usb 2 connections usb 2 3 4 5 for front panel support a type a usb connector usb 10 3 and a vertical usb connector j usb3 1 support 3 connections for front access cables not included see the tables for pin definitions
- C1 monitors power supply fan and system temperatures see the table on the right for pin definitions
- Universal serial bus usb
- C connector jp
- C connector
- Two usb 2 ports usb 0 1 and two
- C connection on your system
- Two ethernet ports lan1 2 are located on the i o backplane these are 10 gb ports on the 6028r trt and 1 gb ports on the 6028r tr in addition a dedicated ipmi lan port located above the usb 0 1 ports on the backplane all these ports accept rj45 type cables
- A system management bus header for ipmi 2 is located at jipmb1 connect the appropriate cable here to use the ipmb
- Two com connections com1 com2 are located on the serverboard com1 is located on the rear i o panel com2 located next to pci e slot1 is used to provide front access sup port see the table on the right for pin definitions
- 19 5 18
- The standby power header is located at jstby1 on the serverboard see the table on the right for pin defini tions you must also have a cable to use this feature
- Standby power
- 9 jumper settings
- 21 5 20
- X8dt3 ln4 ln4f
- X8dt3 i f ln4f
- 23 5 22
- 10 onboard indicators
- 12 installing software
- 11 sata ports
- 25 5 24
- Superdoctor 5
- 27 5 26
- 13 onboard battery
- Precautions
- Chapter 6 advanced chassis setup
- Chapter 6
- Advanced chassis setup
- 1 static sensitive devices
- System fan failure
- Replacing system fans
- 3 system fans
- 2 control panel
- Sata drive installation
- Accessing the drive bays
- 4 drive bay installation removal
- Removing replacing the power supply
- Power supply failure
- Hard drive backplane
- Dvd drive installation optional
- 5 power supply
- Starting bios setup utility
- How to change the configuration data
- Chapter 7 bios
- Chapter 7
- 1 introduction
- How to start the setup utility
- 2 main setup
- Power configuration
- Boot feature
- 3 advanced setup configurations
- Cpu configuration
- Socket 0 pcied00f0 port 0 dmi
- North bridge
- Iio1 configuration
- Iio0 configuration
- Iio configuration
- Qpi quick path interconnect configuration
- Ioat configuration
- Intel vt for directed i o vt d
- Memory ras reliability_availability_serviceability configuration
- Memory configuration
- Dimm information
- 11 7 10
- Usb configuration
- South bridge configuration
- 13 7 12
- 15 7 14
- Sata configuration
- Ssata configuration
- 17 7 16
- Server me management engine configuration
- Pcie pci pnp configuration
- 19 7 18
- Super io configuration
- 21 7 20
- Serial port console redirection
- Console redirection settings
- 23 7 22
- Sol com2 console redirection settings
- 25 7 24
- Trusted computing available when a tpm device is installed and detected by the bios
- 27 7 26
- 4 event logs
- 29 7 28
- Iscsi configuration
- Change smbios event log settings
- Acpi settings
- System event log
- 5 ipmi
- 31 7 30
- Bmc network configuration
- 33 7 32
- 7 boot settings
- 6 security settings
- 35 7 34
- 8 save exit
- 37 7 36
- Appendix a bios error beep codes
- Appendix a
- These fatal errors are usually communicated through a series of audible beeps the numbers on the fatal error list correspond to the number of beeps for the cor responding error
- Non fatal errors are those which in most cases allow the system to continue to boot the error messages normally appear on the screen
- Motherboard bios error beep codes
- Fatal errors will not allow the system to continue with bootup procedure if a fatal error occurs you should consult with your system manufacturer for possible repairs
- During the post power on self test routines which are performed at each system boot errors may occur
- Bios error beep codes
- System specifications
- Serverboard
- Sata controller
- Processors
- Memory capacity
- Expansion slots
- Drive bays
- Chipset
- Appendix b system specifications
- Appendix b
- Weight
- System input requirements
- System cooling
- Regulatory compliance
- Power supply
- Operating environment
- Chassis
- B 2 b 3
- Erver 6028r tr trt user s manual
Похожие устройства
-
Supermicro SYS-7047GR-TRF, X9DRG-QF C602 Dual Xeon Socket2011 1866/1600/1333/1066/800MHz, up to 192GB DDR3 ECC Reg, 10xSATA, 1620WИнструкция по эксплуатации -
Supermicro SYS-7048R-TR, X10DRi C612 Dual Xeon Socket2011-3 2133/1866/1600MHz, up to 1TB DDR4 ECC Reg, 8xSATA3, 920W (1+1)Инструкция по эксплуатации -
Supermicro SYS-7048R-TRT, X10DRi-T C612 Dual Xeon Socket2011-3 2133/1866/1600MHz, up to 1TB DDR4 ECC Reg, 8xSATA3, 920W (1+1)Инструкция по эксплуатации -
Supermicro SYS-7047R-TRF, X9DRi-F C602 Dual Xeon Socket2011, 800-1600MHz, up to 512MB DDR3 ECC Reg, 8xSATA3, 920W (1+1)Инструкция по эксплуатации -
Supermicro SYS-5018R-МRИнструкция по эксплуатации -
Supermicro SYS-1028R-WC1RTИнструкция по эксплуатации -
Supermicro SYS-1028R-WC1RИнструкция по эксплуатации
-
Supermicro SYS-1018GR-TИнструкция по эксплуатации -
Supermicro SYS-5018A-TN4Инструкция по эксплуатации -
Supermicro SYS-5019S-MN4Инструкция по эксплуатации -
Supermicro SYS-6028R-TRTИнструкция по эксплуатации -
Supermicro sys-5018d-mtrfИнструкция по эксплуатации