Stanley stbs720 [6/56] Labels on tool
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Stanley stbs720 [6/56] Labels on tool

Stanley stbs720 [6/56] Labels on tool
6
Motor
Be sure your power supply agrees with nameplate marking.
This information is printed on the nameplate. Lower voltage
will cause loss of power and can result in over-heating. All
STANLEY tools are factory-tested; if this tool does not
operate, check the power supply.
Use Of Extension Cords
Make sure the extension cord is in good condition before
using. Always use the proper size extension cords with the
tool – that is, proper wire size for various lengths of cord and
heavy enough to carry the current the tool will draw. Use of
an undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
Specific Safety Rules
• Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
Warning! Use of this tool can generate and/ or
disburse dust, which may cause serious and
permanent respiratory or other injury. Always
use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from
face and body.
Caution! Wear appropriate hearing protection
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
Warning!
• Always wear eye and respiratory protection.
• Clean your tool out periodically.
Safety of others
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc. Even with
the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks can
not be avoided. These include:
• Injuries caused by touching any rotating/moving parts.
• Injuries caused when changing any parts, blades or
accessories.
• Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
• Impairment of hearing.
• Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level
may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition to
the trigger time.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
Labels on tool
The label on your tool may include the following symbols:
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
ENGLISH (Original instructions)

Содержание

Похожие устройства

ENGUSH Original instructions Motor Injuries caused by touching any rotating moving parts Be sure your power supply agrees with nameplate marking This information is printed on the nameplate Lower voltage will cause loss of power and can result in over heating All STANLEY tools are factory tested if this tool does not operate check the power supply Injuries caused when changing any parts blades or accessories Use Of Extension Cords Make sure the extension cord is in good condition before using Always use the proper size extension cords with the tool that is proper wire size for various lengths of cord and heavy enough to carry the current the tool will draw Use of an undersized cord will cause a drop in line voltage resulting in loss of power and overheating Specific Safety Rules Avoid prolonged contact with dust from power sanding sawing grinding drilling and other construction activities Wear protective clothing and wash exposed areas with soap and water Allowing dust to get into your mouth eyes or lay on the skin may promote absorption of harmful chemicals Warning Use of this tool can generate and or J disburse dust which may cause serious and 1 5 permanent respiratory or other injury Always use NIOSH OSHAapproved respiratory protection appropriate for the dust exposure Direct particles away from face and body Caution Wear appropriate hearing protection during use Under some conditions and duration of use noise from this product may contribute to hearing loss Warning Always wear eye and respiratory protection Injuries caused by prolonged use ofa tool When using any tool for prolonged periods ensure you take regular breaks Impairment of hearing Health hazards caused by breathing dust developed when using your tool example working with wood especially oak beech and MDF Vibration The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN 60745 and may be used for comparing one tool with another The declared vibration emission value may also be used in a preliminary assessment of exposure Warning The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used The vibration level may increase above the level stated When assessing vibration exposure to determine safety measures required by 2002 44 EC to protect persons regularly using power tools in employment an estimation of vibration exposure should consider the actual conditions of use and the way the tool is used including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time Labels on tool Clean your tool out periodically The label on your tool may include the following symbols Safety of others This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Residual risks Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings These risks can arise from misuse prolonged use etc Even with the application of the relevant safety regulations and the implementation of safety devices certain residual risks can not be avoided These include Read Instructions Manual Hz Hertz Use Eye Protectbn min minutes Alternating Current Use Ear Protection V Volts A Amperes 0 Class II Constructbn Earthing Terminal A Safety Alert Symbol N Watts Direct Current min n0 No Load Speed Position of date barcode The Date Code which also includes the year of manufacture is printed into the housing Example 2014XXJN Year of manufacturing Revolutions or Recipro cation per minute

Скачать