Home
Главная
Stanley
Шлифмашина
stbs720
Инструкция по эксплуатации Страница: 7

Stanley stbs720 [7/56] Características fig a

Electrical safety

Your tool is double insulated; therefore no earth

wire is required. Always check that the main

voltage corresponds to the voltage on the rating

plate.

Warning! If the power cord is damaged, it must

be replaced by the manufacturer, authorized

STANLEY Service Center or an equally qualiﬁed

person in order to avoid damage or injury. If the power cord

is replaced by an equally qualiﬁed person, but not authorized

by STANLEY, the warranty will not be valid.

Caracteristicas (FIG. A)

1. Lock on switch for continuous use

2. Dust extraction duck

3. Way adjustable handle

4. Aluminum cover

5. Belt tracking adjustment knob

6. Sanding belt

7. Single action belt release lever

Adjustments

Warning! To prevent accidental operation, turn off

and unplug sander before performing the following

operations. Failure to do this could result in

serious personal injury.

3 Position handle (FIG. B1 and B2)

A locking mechanism on the side of the handle can be

loosened to allow the handle to move. To adjust the handle,

pull out on the locking arm (FIG. B1) and move the handle to

the desired position (FIG. B2). Once the handle is in

position, push the locking arm in to lock the handle into

position.

2 Position belt cover (FIG. C and D)

The belt sander has an aluminum sanding belt cover at the

front. When the handle is positioned in the uppermost

position, this cover can be raised as shown in FIG. C (Arrow

1) and locked in this position to:

a. Improve accessibility to narrow areas.

b. Allow the use of the smaller diameter front roller to sand

with (normally the aluminum cover prevents this when in

the “down” position).

c. Expose the top part of the belt for more versatile

sanding (FIG. D).

To lower the belt cover, grasp the ﬂange on the side and

move it slightly in the direction shown in FIG. C (Arrow 2)

and return it to its closed position.

Note: The sanding belt cover cannot be locked in its raised

position unless the bail handle is in the uppermost position.

Warning! The sanding belt is exposed when the

belt cover is raised. Use extra caution when

operating in this mode.

Adjusting the sanding belt tracking (FIG. E)

Turn the machine upside down (FIG. E), hold it ﬁrmly with

one hand, start motor and release switch immediately after

observing tracking of sanding belt. If abrasive belt runs

outward, turn tracking adjustment knob clockwise and

counterclockwise if belt runs inward. Belt life will be greatly

increased by keeping the tracking adjustment set properly

(FIG. E).

Changing the sanding belt (FIG. F and G)

Warning! To prevent accidental operation, turn off and

unplug sander before changing the sanding belt. Pull the

lever shown in FIG. 5 to release the tension on the sanding

belt. Pull the sanding belt from the two rollers. Put the new

3” x 21” (76 x 533mm) sanding belt in position on the front

and rear rollers (FIG. 6). Ensure that the arrows on the

sanding belt and on your belt sander are pointing in the

same direction. Push the lever to the rear to tension the

sanding belt.

Dust collection (FIG. H)

Warning! To prevent accidental operation, turn off

and unplug sander before installing the dust bag.

When using your belt sander, dust and grit are produced. It

is important to use a dust bag. Connect the dust bag by

sliding the plastic opening of the bag down over the dust

exhaust port of the sander as shown in FIG. 7. To empty the

dust bag, remove it from the sander and unzip the bag over

a trash container.

Warning! Fire hazard. Collected sanding dust

from sanding surface coatings (polyurethane,

linseed oil, etc.) can self-ignite in sander dust

bag or elsewhere and cause ﬁre. To reduce risk, empty

bag frequently and strictly follow sander manual and coating

manufacturer’s instructions.

Warning! Fire hazard. When working on metal

surfaces, do not use the dust bag or a vacuum

cleaner because sparks are generated. Wear

safety glasses and a dust mask. Due to the danger of ﬁre,

do not use your belt sander to sand magnesium surfaces.

Do not use for wet sanding.

(Original instructions) ENGLISH

Содержание

Похожие устройства

Original instructions ENGLISH Electrical safety Your tool is double insulated therefore no earth wire is required Always check that the main voltage corresponds to the voltage on the rating plate Warning If the power cord is damaged it must be replaced by the manufacturer authorized STANLEY Service Center or an equally qualified person in order to avoid damage or injury If the power cord is replaced by an equally qualified person but not authorized by STANLEY the warranty will not be valid Características FIG A 1 Lock on switch for continuous use 2 Dust extraction duck 3 Way adjustable handle 4 Aluminum cover 5 Belt tracking adjustment knob 6 Sanding belt 7 Single action belt release lever Adjustments Warning To prevent accidental operation turn off and unplug sander before performing the following operations Failure to do this could result in serious personal injury To lower the belt cover grasp the flange on the side and move it slightly in the direction shown in FIG C Arrow 2 and return it to its closed position Note The sanding belt cover cannot be locked in its raised position unless the bail handle is in the uppermost position Warning The sanding belt is exposed when the J belt cover is raised Use extra caution when operating in this mode Adjusting the sanding belt tracking FIG E Turn the machine upside down FIG E hold it firmly with one hand start motor and release switch immediately after observing tracking of sanding belt If abrasive belt runs outward turn tracking adjustment knob clockwise and counterclockwise if belt runs inward Belt life will be greatly increased by keeping the tracking adjustment set properly FIG E Changing the sanding belt FIG F and G Warning To prevent accidental operation turn off and unplug sander before changing the sanding belt Pull the lever shown in FIG 5 to release the tension on the sanding belt Pull the sanding belt from the two rollers Put the new 3 x 21 76 x 533mm sanding belt in position on the front and rear rollers FIG 6 Ensure that the arrows on the sanding belt and on your belt sander are pointing in the same direction Push the lever to the rear to tension the sanding belt Dust collection FIG H 3 Position handle FIG B1 and B2 A locking mechanism on the side of the handle can be loosened to allow the handle to move To adjust the handle pull out on the locking arm FIG B1 and move the handle to the desired position FIG B2 Once the handle is in position push the locking arm in to lock the handle into position 2 Position belt cover FIG C and D The belt sander has an aluminum sanding belt cover at the front When the handle is positioned in the uppermost position this cover can be raised as shown in FIG C Arrow 1 and locked in this position to a Improve accessibility to narrow areas b Allow the use of the smaller diameter front roller to sand with normally the aluminum cover prevents this when in the down position c Expose the top part of the belt for more versatile sanding FIG D Warning To prevent accidental operation turn off and unplug sander before installing the dust bag When using your belt sander dust and grit are produced It is important to use a dust bag Connect the dust bag by sliding the plastic opening of the bag down over the dust exhaust port of the sander as shown in FIG 7 To empty the dust bag remove it from the sander and unzip the bag over a trash container Warning Fire hazard Collected sanding dust from sanding surface coatings polyurethane linseed oil etc can self ignite in sander dust bag or elsewhere and cause fire To reduce risk empty bag frequently and strictly follow sander manual and coating manufacturer s instructions Warning Fire hazard When working on metal surfaces do not use the dust bag or a vacuum cleaner because sparks are generated Wear safety glasses and a dust mask Due to the danger of fire do not use your belt sander to sand magnesium surfeces Do not use for wet sanding

Скачать