Home
Главная
Vitek
Утюг
VT-1229
Инструкция по эксплуатации Страница: 5

Vitek VT-1229 [5/48] English

E N G L I S H

(6) is blinking. When you start ironing the iron

is switched on automatically.

Choice of water

To fill the water tank use regular tap water. If the

water is hard then it is recommended to mix it

with distilled water at a ratio of 1:1, if the water

is very hard, mix it with distilled water at a ratio of

1:2 or use only distilled water.

Double anti-scale system

The iron is equipped with double anti-scale sys-

tem that consists of installed self-clean system

and Cartridge for water softening (14). If the wa-

ter is hard in your region, follow the instruction of

section “Choice of water”.

Before usage

− Take out the iron from the package and re-

move the protective cartoon covering from

the iron soleplate (13).

− Make sure that the electrical supply voltage

corresponds to the iron’s operating voltage.

Filling the water tank

Make sure that the iron is disconnected from

electrical power before filling it with water.

− Set the temperature regulator (9) in position

«MIN», set the steam release regulator (4) to

the position « » (to the position of steam va-

por OFF).

− Open the water tank lid (2) and make sure that

the cartridge is in (14) (pict. 1)

− Using the measuring cup (15), fill the water

tank with water (10), close the lid (2).

Note:

− Do not fill the water tank (10) with scented

liquids, vinegar, starch solutions, descaling

reagents, chemical substances etc.

− Do not fill it with water above MAX. indicator

(12).

− If you need to refill the water tank during iron-

ing, turn off the iron and unplug the power

cord from the outlet.

Ironing temperature

− Always check the recommended iron tem-

perature indicated on the tag before ironing.

− If the tag does not list the recommended iron-

ing temperature, but you know the type of

fabric, then use the following table to deter-

mine the proper temperature.

Determination Fabric type (temperature)

•

Synthetics, nylon, acryl, polyester

(low temperature)

••

Silk/wool (medium temperature)

•••

Cotton/linen (high temperature)

MAX

Maximum temperature

The table is applicable only to smooth materi-

als.- If another type of material (goffered, em-

bossed, etc.), then it is best to iron it at low tem-

perature.

− First things are to be sorted according to

ironing temperature: synthetics to synthet-

ics, wool to wool, cotton to cotton, etc.

− Iron heats up faster than gets cold. So first

it is recommended to iron things at low tem-

perature (for example, synthetic fabrics).

− After that start ironing at higher temperatures

(silk, wool).- Items made of cotton and linen

should be ironed at the last turn.

− If the material contains mixed fibers, it is nec-

essary to establish the lowest temperature of

ironing (for example, if the product consists

of elastane and cotton, it should be ironed at

a temperature suitable for elastin «•»).

− If you can’t determine the composition of tis-

sue, then look for a product space that is not

noticeable when wearing, and empirically se-

lect the temperature of ironing (always start

with the lowest temperature and gradually

increase it until you get the desired result).

− Corduroy and other tissues, which rapidly

begin to be glossy, should be strictly be

ironed in one direction (in the direction with

the nap) with a slight pressure.

− In order to avoid shiny patches on synthetic

and silk fabrics, irone them from the inside.

Setting the ironing temperature

− Put the iron on the base (8).

− Plug the power cord into an outlet.

− Turn the regulator(9), set the desired tem-

perature of ironing: «•», «• •», «• • •» or

«MAX», depending on tissue type, when that

Vitek VT-1229 [5/48] English

Содержание

Похожие устройства