![Castel MAC HC 40 NTV Инструкция по эксплуатации онлайн [10/18] 272069](/img/pdf.png)
Castel MAC HC 40 NTV Инструкция по эксплуатации онлайн [10/18] 272069
![Castel MAC HC 40 NTV Инструкция по эксплуатации онлайн [10/18] 272069](/views2/1318627/page10/bga.png)
10
GB
4.1 Turning the machine on
Provide the conservator with voltage by turn-
ing the main mains switch on.
Turn on the controller while keeping the
ON/OFF switch pressed , the controller
shows the welcome message, the version of
the software installed, the cabinet model and
then goes on to the following mask.
Message with compressor off and display of
inside cell temperature.
The cabinet has been prepared for function-
ing at the preset temperature.
Message with compressor on and display of
inside cell temperature.
The temperature on the display is the temper-
ature detected by the sensor inside the cell.
To turn off the controller, keep the ON/OFF
button pressed for five consecutive sec-
onds after which the controller enters low volt-
age stand-by function mode and will display
the following mask
The message displayed on the LCD screen in
the turning off phase is STAND-BY with blink-
ing cursor.
CAUTION to remove the voltage from the
controller switch the main mains switch.
4.2 Setting the language
Press the MENU button and with buttons or
go to MENU 7 LANGUAGE; the first lan-
guage is displayed when the ENTER but-
ton is pressed. The next time the button or
is pressed selects the languages available.
Menu 7
LANGUAGE
COOLING >>OK
CELL -12,5°C
PAUSE >>OK
CELL -14,5°C
AWAITED _
TURNING OFF
ON/OFF
Activation of continuous
operation recirculation
ventilation
Infrared
data receiver
Select the
menu
Decrease the
value
Confirm the entrance to the menu selected
or the value selected
Increase the value
Содержание
- Conservation cabinets 1
- Highcontrol 1
- Instructions for use 1
- General documentation 4
- General information 4
- Out fig for the stainless steel versions wear protective gloves when han dling the packaging and the wooden base 4
- Installation 5
- Accessories 8
- Hc 20 c nt ntv ntb btv fx 8
- Hc 20 nt 2 bt 2 btv 2 8
- Hc 40 btv ntb ntv 8
- Operating spaces 8
- Positioning 8
- Technical characteristics 9
- Date 12 04 03 time 11 54 23 11
- Hc20nt 2 hc20ntv hc20btv hc20btv 2 hc40ntv hc40btv 11
- Menu 2 change setpoint 11
- New set 15 c current 15 c 11
- Ok cell 21 c 11
- Call service 12
- Defrosting management 12
- F18 defr time s 19 02 02 06 09 12
- Menu 4 defrosting 12
- Ok cell 10 5 c 12
- Ok cell 18 c 12
- Al 27 high temp duration 015 13
- Al 27 high temp max temp 25 c 13
- Al 27 high temp s 18 03 02 12 29 13
- Alarm detected cell 24 0 c 13
- Ht cell 18 c 13
- Lt cell 24 c 13
- Management of the alarms detected and turning them off 13
- Al 26 black out b 15 03 02 10 22 14
- Al 26 black out max temp 12 c 14
- Al 26 black out s 15 03 02 10 01 14
- Alarm detected cell 24 0 c 14
- Button the cancellation is automatic when the mal function is rectified the alarm is however logged in the alarm menu 14
- Contact an authorised tecnomac centre in the case of a serious alarm 14
- Example of a blackout alarm 14
- Important 14
- In the case of high low temperature alarms before being registered a prealarm time of sixty minutes is calculated at the end of this time the controller logs the alarm in the alarm log and shows the following mask on the display 14
- Malfunctioning message they jeopardise machine operation call the service message display cause cancellation 14
- Serious alarm list serious alarms can determine the incorrect functioning of the conservator the display is the same as that described for the alarms and the signalling buzzer is acti vated to silence the buzzer press the 14
- To eliminate the indication go into the alarm log as shown in the paragraph above 14
- Alarm detected fixed logging of a remove the cause of the alarm alarm in the log and enter into menu 1 alarm log to reset the controller 15
- Ht fixed high temp prealarm automatic rectification 15
- List of any other malfunctions that cannot be signalled 15
- Lt fixed low temp prealarm automatic rectification 15
- Set clock loss of clock data set clock data 15
- Signalling messages they do not jeopardise the functioning of the machine message display cause cancellation 15
- Ordinary maintenance 16
Похожие устройства
- Castel MAC TC 60 N Инструкция по эксплуатации
- Castel MAC HC 20 BT Инструкция по эксплуатации
- Castel MAC HC 20 NTB Инструкция по эксплуатации
- Steno PL7B Инструкция по эксплуатации
- ТОРГМАШ УКМ-14 Инструкция по эксплуатации
- ТОРГМАШ УКМ-14 Сертификат
- ТОРГМАШ УКМ-14 Каталог оборудования ТОРГМАШ
- Pavoni MINITEMPER Инструкция по эксплуатации
- Pavoni MINITEMPER Каталог оборудования Pavoni (англ.)
- Castel MAC HC 20 C Инструкция по эксплуатации
- Talsa Н26pa Инструкция по эксплуатации
- Talsa H42pas Инструкция по эксплуатации
- Talsa Н31pas Инструкция по эксплуатации
- Talsa Н15pa Инструкция по эксплуатации
- Helia Smoker 48 Инструкция по эксплуатации
- Helia Smoker 48 Рецепты копчения
- Helia Smoker 24 Инструкция по эксплуатации
- Helia Smoker 24 Рецепты копчения
- CAS CNW-460 Инструкция по эксплуатации
- CAS СNW-520 Инструкция по эксплуатации