SERA 5Вт 750л/ч 400л макс. [15/98] Sera filter and feed pump fp 750

SERA 5Вт 750л/ч 400л макс. [15/98] Sera filter and feed pump fp 750
15
sera lter and feed pump FP 750
The sera lter and feed pump FP 750 convinces with
its compact and robust construction as well as low en-
ergy consumption and its adjustability. The high water
agitation performance ensures constant conditions in an
aquarium and thus contributes to the stabilization of the
biological system.
Parts list
Motor block with pump chamber
Holder plate with four suction cups
Hose connector
Running unit consisting of
Rubber bearing
Rotor with magnetic impeller and ceramic shaft
Seal ring
Pump chamber cover
Intake grid
Rotary adjusting cap
Attention! Please observe the safety advice by all means.
Assembly instruction
The sera lter and feed pump FP 750 is connected to
the intake opening of the sera UV-C System 5 W (4.1)
by a hose, and is inserted with it into the central duct of
the sera bioactive IF 400 + UV internal lter (4.2).
Operation
Make sure there is no direct or indirect conducting con-
tact to persons before switching on the pump. The pump
begins to run upon plugging in the plug. The water ow
through the pump will be reduced when turning the cap
(6.8) in “–” direction. The water ow will rise up to the
maximum feed performance when turning the cap in “+”
direction. The pump is designed for permanent opera-
tion but must not run dry, as the motor block is cooled
by water and the ceramic shaft is lubricated by water.
Turn the pump off again and check whether nothing is
clogged if no water is delivered after a few seconds.
Switch the pump back on only afterwards.
Cleaning
All parts can be cleaned with a brush and a neutral de-
tergent. Make sure no detergent gets into the aquarium.
Carefully rinse all cleaned parts with clean tap water be-
fore reassembling the pump and putting it back in oper-
ation in the aquarium. You can immerse the running unit
and the motor block in a descaler solution for stainless
steel parts if the pump is severely lime encrusted. Please
adhere to the information for use of the descaler solu-
tion.
Maintenance
The motor block is embedded in plastic material for elec-
tric isolation and therefore cannot be repaired.
Replacing the running unit:
Take the pump intake grid off the motor block. Turn the
pump chamber cover to the left by approximately 90°.
Pull the pump chamber cover straightly out of the mo-
tor block, making sure the shaft cannot break. In case
the shaft remains stuck in the motor block, pull it out rst
before pulling out the magnetic impeller.
Reassembly takes place in reverse order.
Technical Data
sera FP 750
Voltage 220 – 240 V ~ 50 Hz
Power uptake 12 W
Water temperature up to 35°C (95°F)
Cable length 1.8 m (6 ft.)
Spare parts
Running unit (rotor with magnetic impeller, ceramic shaft,
rubber bearings)
Pump chamber cover with seal ring
Suction holder
Warning
1. Children should be supervised to ensure that they do
not play with the appliance.
2. This appliance is not intended for use by persons (in-
cluding children) with reduced physical, sensory or
mental capacities, or lack of experience and knowl-
edge, unless they have been given supervision or in-
struction concerning use of the appliance by a person
responsible for their safety.
3. If the supply cord is damaged, the pump is not longer
allowed to be used and should be discarded.
Disposal of the unit:
Waste electrical and electronic equipment (WEEE)
must not get into domestic waste!
If ever the unit cannot be used anymore, the consumer
is legally obliged to hand in waste electrical and elec-
tronic equipment (WEEE) separately from domestic
waste, e.g. at a collection point of his community/his
district. This ensures that waste electrical and electron-
ic equipment (WEEE) is expertly processed and that neg-
ative effects to the environment are avoided.
sera bioactive IF 400 + UV Innenfilter neu.indd 15 26.08.2014 12:20:43

Содержание

Похожие устройства

Скачать