AEG WS2200-230 4935428500 [15/128] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

AEG WS2200-230 4935428500 [15/128] English

AEG WS2200-230 4935428500 [15/128] English
12
GB
English
c) When wheel is binding or when interrupting a cut for any
reason, switch o the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-o wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully re-enter the cut. The
wheel may bind, walk up or kickback if the power tool is restarted in
the workpiece.
e) Support panels or any oversized workpiece to minimize the
risk of wheel pinching and kickback. Large workpieces tend to sag
under their own weight. Supports must be placed under the workpiece
near the line of cut and near the edge of the workpiece on both sides
of the wheel.
f) Use extra caution when making a “pocket cut” into existing
walls or other blind areas. The protruding wheel may cut gas or
water pipes, electrical wiring or objects that can cause kickback.
Safety Warnings Specic for Sanding Operations:
a) Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when selecting
sanding paper. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may cause snagging,
tearing of the disc or kickback.
Safety Warnings Specic for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the wires
by applying excessive load to the brush. The wire bristles can
easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or brush
with the guard. Wire wheel or brush may expand in diameter due
to work load and centrifugal forces.
Additional Safety and Working Instructions:
When grinding metal, ying sparks are produced. Take care that
no persons are endangered. Because of the danger of re, no
combustible materials should be located in the vicinity (spark ight
zone). Do not use dust extraction.
Avoid ying sparks and sanding dust hit your body.
Never reach into the danger area of the machine when it is running.
Immediately switch o the machine in case of considerable vibra-
tions or if other malfunctions occur. Check the machine in order to
nd out the cause.
Under extreme conditions (e.g. smooth-grinding metals with
the arbour and vulcanized bre grinding disk), signicant
contamination can build up on the inside of the angle grinder. For
safety reasons, in such conditions a ground fault interrupter must
be connected in series. If the ground fault interrupter trips the
machine must be sent for service.
Chips and splinters must not be removed while the machine is
running.
MAINS CONNECTION
Connect only to single-phase AC system voltage as indicated on
the rating plate. It is also possible to connect to sockets without an
earthing contact as the design conforms to safety class II.
Appliances used at many dierent locations including wet room
and open air must be connected via a residual current device (FI,
RCD, PRCD) of 30mA or less.
Only plug-in when machine is switched o.
Do not let any metal parts enter the airing slots - danger of short
circuit!
Inrush currents cause short-time voltage drops. Under unfavoura-
ble power supply conditions, other equipment may be aected. If
the system impedance of the power supply is lower than 0,2 Ohm,
disturbances are unlikely to occur.
SPECIFIED CONDITIONS OF USE
The angle grinder is intended for grinding and cutting metal, stone
and ceramicmaterials as well as sanding and wire brushing.
Use the cutting guard from the accessories range for cutting
application.
Please refer to the instructions supplied by the accessory manu-
facturer.
The machine is suitable only for working without water.
WORKING TIPS
For accessories intended to be tted with threaded hole wheel,
ensure that the thread in the wheel is long enough to accept the
spindle length.
Always use and store the cutting and grinding disks according to
the manufacturer‘s instructions.
Always use the correct guard for cutting and grinding.
The grinding surface of the centre depressed disks must be moun-
ted min. 2 mm below the plane of the guard lip.
The adjusting nut must be tightened before starting to work with
the machine.
Always use the auxiliary handle.
The workpiece must be xed if it is not heavy enough to be steady.
Never move lead the workpiece towards the rotating disk by hand.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
If the supply cord of this power tool is damaged, it must be
replaced by a specially prepared cord available through the service
organization.
Use only AEG accessories and spare parts. Should components need to
be replaced which have not been described, please contact one of our
AEG service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the machine type printed as well as the six-digit No. on the label
and order the drawing at your local service agents or directly at:
Techtronic Industries GmbH, Max-Eyth-Straße10, 71364Winnen-
den, Germany.

Содержание

Похожие устройства

c When wheel is binding or when interrupting a cut for any reason switchoff the power tool and hold the power tool MAINS CONNECTION motionless until the wheel comes to a complete stop Never Connectonly to single phase AC system voltage as indicated on attempt to remove the cut off wheel from the cut while the the rating plate It is also possible to connect to sockets without an wheel is in motion otherwise kickback may occur Investigate earthing contact as the design conforms to safety class II and take corrective action to elim inate the cause of wheel binding Appliances used at many different locations including wetroom d Do not restart the cutting operation in the workpiece Let the wheel reach full speedandcarefully re enter the cut The and open air must be connected via a residual current device Fl RCO PRCD of 30mA or less wheel may bind walk up or kickback if the power tool is restarted in Only plug in when machine is switched off the workpiece Do not letany metal parts enter the airing slots danger of short e Support panels or any oversized workpiece to minimize the circuit risk of wheel pinching and kickback Large workpieces tend to sag Inrush under theirown weight Supports must be placed under the workpiece ble power supply conditions other eguipment may be affected If near the line of cut and near the edge of the workpiece on both sides the system impedance of the power supply is lower than 0 2 Ohm of the wheel disturbances are unlikely to occur f Use extra caution when making a pocket cut into existing walls or other blind areas The protruding wheel may cut gas or water pipes electrical wiring or objects that can cause kickback currents causeshort time voltagedrops Underunfavoura SPECIFIED CONDITIONS OF USE The angle grinder is intended for grinding and cutting metal stone and ceramic materials as well as sanding and wire brushing GB Safety Warnings Specific for Sanding Operations Use the cutting guard from the accessories range for cutting a Do not use excessively oversized sanding disc paper application Follow manufacturers recommendations when selecting Please refer to the i n str uct ion s suppl ied by the accessory manu sanding paper Larger sanding paperextending beyond the facturer sanding pad presents a laceration hazard and may cause snagging The machine is suitable only for working withoutwater tearing ofthe discor kickback WORKING TIPS Safety Warnings Specific for Wire Brushing Operations a Be aware that wire bristles are thrown by the brush even during ordinary operation Do not overstress the wires by applying excessive load to the brush The wire bristles can easily penetrate light clothing and or skin b If the use of a guard is recommended for wire brushing do notallow any interference of the wire wheel or brush with the guard Wire wheel or brush may expand in diameter due to workload and centrifugal forces For accessories intended to befitted with threaded hole wheel ensure that the thread in the wheel is long enough to accept the spindle length Always use a nd store the cutting and grinding disks according to the manufacturer s instructions Always usethe correct guard for cutting andgrinding The grinding surface of thecentre depressed disks must be moun ted mi n 2 mm below the plane of the guard I ip The adjusting nut must be tightened before starting to work with Additional Safety and Working Instructions the machine When grinding metal flying sparks are produced Take care that Always use the auxiliary handle no persons a re endangered Because of the danger of fire no The workpiece must be fixed if it is not heavy enough to be steady combustible materia Is should be located in the vicinity sparkflight Never move lead the workpiece towards the rotating disk by hand zone Do not use dust extraction MAINTENANCE Avoid flying sparks and sanding dust hit your body Never reach into the dangerarea of the machine when it is running Immediately switch off the machine in case of considerable vibra tions or if other malfunctions occur Check the machine in order to find outthe cause Underextremeconditions e g smooth grinding metals with the arbour and vulcanized fibre grinding disk significant contamination can build up on the insideof theanglegrinder For The ventilation slots ofthe machine must be kept clear at all times If the supply cord of this power tool is damaged it must be replaced by a specially prepared cord available through the service organization Use only AEG accessories and spare parts Should components need to be replaced which have not been described please contact one ofour AEG service agents see our list of guarantee service addresses safety reasons in such conditions a ground fault interrupter must If needed an exploded view ofthe tool can be ordered Please state be connected in series If the ground fault inter ru pte r tri ps the the machine type printed as well as the six digit No on the label machine must besent for service and order the dra wing at your local service agents or directly at Chips and splinters must not be removed while the machine is running English Techtronic I nd u st ri es GmbH Max Eyt h St raB e 10 71364 W innenden Germany

Скачать