Home
Главная
Pioneer
Автомагнитола
DEH-2910MP
Руководство по установке Страница: 2

Pioneer DEH-2910MP [2/4] Connecting the units english

Note:

• When this unit is installed in a vehicle without

ACC (accessory) position on the ignition switch,

red cable must be wired to the terminal that can

detect the operation of the ignition key.

Otherwise, battery drain may result.

• Use this unit in other than the following condi-

tions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunc-

tion, be sure to follow the directions below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhe-

sive tape around them where they lie against

metal parts.

— Place all cables away from moving parts,

such as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker’s nega-

tive cables.

• Control signal is output through blue/white cable

when this unit is powered on. Connect it to an

external power amp’s system remote control or

the vehicle’s auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is

equipped with a glass antenna, connect it to the

antenna booster power supply terminal.

• Never connect blue/white cable to external power

amp’s power terminal. Also, never connect it to

the power terminal of the auto antenna.

Otherwise, battery drain or malfunction may

result.

• Black cable is ground. This cable and other prod-

uct’s ground cable (especially, high-current prod-

ucts such as power amp) must be wired separate-

ly. Otherwise, fire or malfunction may result if

they are accidentally detached.

• Cord function may differ according to the

product, even if cord color is the same. When

connecting this system, be sure to check all

manuals and connect cords correctly.

No ACC positionACC position

Connecting the Units ENGLISH

Right

White

Gray

White/black

Green

Green/black

Gray/black

Violet

Violet/black

Front speaker

Left

Perform these connections when using

the optional amplifier.

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Fuse (10 A)

Rear output

Antenna jack

This Product

Blue/white

Connect to system control terminal of the

power amp or Auto-antenna relay control

terminal (max. 300 mA 12 V DC).

System remote control

Power amp

(sold separately)

Front speaker

Rear speakerRear speaker

Yellow/black

If you use an equipment with Mute function, wire

this lead to the Audio Mute lead on that equipment.

If not, keep the Audio Mute lead free of any

connections.

Yellow

Connect to the constant 12 V supply terminal.

Red

Connect to terminal controlled by ignition swich (12 V DC).

Black (chassis ground)

Connect to a clean, paint-free metal location.

Connect with RCA cables (sold separately)

Содержание

Похожие устройства

Connecting the Units Note When this unit is installed in a vehicle without ACC accessory position on the ignition switch red cable must be wired to the terminal that can detect the operation of the ignition key Otherwise battery drain may result ACC position No ACC position Use this unit in other than the following condi tions could result in fire or malfunction Vehicles with a 12 volt battery and negative grounding Speakers with 50 W output value and 4 ohm to 8 ohm impedance value To prevent short circuit overheating or malfunc tion be sure to follow the directions below Disconnect the negative terminal of the bat tery before installation Secure the wiring with cable clamps or adhe sive tape To protect the wiring wrap adhe sive tape around them where they lie against metal parts Place all cables away from moving parts such as gear shift and seat rails Place all cables away from hot places such as near the heater outlet Do not pass the yellow cable through a hole into the engine compartment to connect to a battery Cover any disconnected cable connectors with insulating tape Do not shorten any cables Never cut the insulation of the power cable of this unit in order to share the power to other equipment Current capacity of the cable is limited Use a fuse of the rating prescribed Never wire the speaker negative cable directly to ground Never band together multiple speaker s nega tive cables ENGLISH Control signal is output through blue white cable when this unit is powered on Connect it to an external power amp s system remote control or the vehicle s auto antenna relay control terminal max 3 X mA 12 V DC If the vehicle is equipped with a glass antenna connect it to the antenna booster power supply terminal Never connect blue white cable to external power amp s power terminal Also never connect it to the power terminal of the auto antenna Otherwise battery drain or malfunction may result Black cable is ground This cable and other prod uct s ground cable especially high current prod ucts such as power amp must be wired separate ly Otherwise fire or malfunction may result if they are accidentally detached Connect with RCA cables sold separately This Product Power amp sold separately 1 Antenna jack Fuse 10 A B lue white Connect to system control terminal of the power amp or Auto antenna relay control terminal max 3 X mA 12 V DC Cord function may differ according to the product even if cord color is the same When connecting this system be sure to check all manuals and connect cords correctly System remote control Yellow black If you use an equipment with Mute function wire this lead to the Audio Mute lead on that equipment If not keep the Audio Mute lead free of any connections White Gray Front speaker Yellow Connect to the constant 12 V supply terminal White black Gray black Right Green Violet I Rear speaker Red Connect to terminal controlled by ignition swich 12 V DC Black chassis ground Connect to a clean paint free metal location With a 2 speaker system do not connect anything to the speaker leads that are not connected to speakers Perform these connections when using the optional amplifier Green hlack Violet hlack

Скачать

Случайные обсуждения

Ответы 0

Нет функции Аукс.

3 года назад

Ответы 1

Последнее время сильно царапает диски, кто знает почему?

7 лет назад

Ответы 1

Распиновка магнитолы, с фото.

7 лет назад

Ответы 2