Главная
Skipped breadcrumb items
DS 14DJL 2.5
Инструкция по эксплуатации Страница: 6

Главная
Hikoki
DS 14DJL 2.5
Инструкция по эксплуатации Страница: 6

Hikoki DS 14DJL 2.5 — рекомендации по зарядке и обслуживанию аккумуляторных инструментов [6/168]

Превью страниц Страница 6 / 168

Hikoki DS 14DJL 2.5 [6/168] Mounting and operation

English

NOTE

The recharging time may vary according to the ambient

temperature and power source voltage.

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used, the

pilot lamp of the charger lights for 1 second, does not

light for 0.5 seconds (oﬀ for 0.5 seconds). In such a case,

ﬁ rst let the battery cool, then start charging.

○ When the pilot lamp ﬂ ickers (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s

battery connector. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

○

Since the built-in micro computer takes about 3 seconds to

conﬁ rm that the battery being charged with charger is taken

out, wait for a minimum of 3 seconds before reinserting it

to continue charging. If the battery is reinserted within 3

seconds, the battery may not be properly charged.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the

battery

1 157

Charging 2 157

Tightening torque adjustment 3 157

Selecting the drill position 4 157

Selecting the impact position 5 157

Change rotation speed 6 157

How to use the LED light 7 158

Mounting the bit 8 158

Reversing the rotational direction 9 158

Switch operation 10 158

Using the bit holder 11 158

Selecting accessories ― 159

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade eﬃ ciency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the driver drill is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

Store the driver drill in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Make sure that the battery is fully charged when stored

for a long period (3 months or more). The battery with

smaller capacity may not be able to be charged when

used, if stored for a long period.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage of batteries with a low charge

may result in performance deterioration, signiﬁ cantly

reducing battery usage time or rendering the batteries

incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

0000Book_DS14DJL.indb 60000Book_DS14DJL.indb 6 2017/12/07 9:51:002017/12/07 9:51:00

Hikoki DS 14DJL 2.5 — рекомендации по зарядке и обслуживанию аккумуляторных инструментов [6/168]

Содержание

Похожие устройства