![Aurora A-1790D Панель управления _eng_ онлайн [136/151] 409087](/img/pdf.png)
Aurora A-1790D Панель управления _eng_ онлайн [136/151] 409087
![Aurora A-1790D Панель управления _eng_ онлайн [136/151] 409087](/views2/1495536/page136/bg88.png)
Appendix 1 Computerized Control System for Square Buttonhole Machine
126
M-026 No warning record
M-027 Clear warning record
Are You Sure？Yes：enter No：X
M-028 USB is pulled out
USB is pulled out
M-029 Can not find pattern in U disk
M-030 Save software version successful
Software version is saved to the root directory of U
disk
M-031 Replace needle
Needle replacement set value is reached, please
replace needle
M-032 Replace oil
Oil replacement set value is reached, please replace oil
M-033 Clean machine
Cleaning machine set value is reached, please clean
machine
M-034 Clear needle replacement set value
Are You Sure？Yes：enter No：X
M-035 Clear oil replacement set value
Are You Sure？Yes：enter No：X
M-036 Clear cleaning time value
Are You Sure？Yes：enter No：X
M-037 Clear production control value
Are You Sure？Yes：enter No：X
M-038 Over sewing range
Please make sure the pattern is within the sewing
range
M-039 Stitch number over range
Please reduce patter stitch number
M-040 Load default patterns
No pattern in memory, please load default patterns
M-041 Patter data not exist
Reload or input from pattern-design software
M-042 Pattern data error
Current pattern data error, it will be replaced by
default patterns
M-043 Pattern information file open failed
Restore to default pattern configuration
M-044 Pattern is existed
Can not repeat the pattern
M-045 Memory full
Please delete the unused patterns
M-046 Cover the pattern
Are You Sure？Yes：enter No：X
M-047 Continuous sewing pattern open error
Pattern file has mistake, it will be deleted
M-048 Cyclic sewing pattern open error
Pattern file has mistake, it will be deleted
M-049 Delete pattern data
Press Enter to delete; Press ESC to quit
M-050 Delete the selected pattern
Are You Sure？Yes：enter No：X
M-051 Pattern is used, can not delete
Please release the quotation at other pattern type
M-052 Save at least one pattern
Can not delete last pattern
M-053 Number not exist
Input again
M-054 Sewing counter reaches set value
Please pres Enter to cleat it
M-055 No.of pcs counter reaches set value
Please pres Enter to cleat it
M-056 Pattern-designing calculation error
M-057 Knife size error
M-058 Sewing code created at pattern-designing error
M-059 Over max stitch interval
M-060 Pattern file type error
M-061 Delete the selected sub-pattern
Are You Sure？Yes：enter No：X
M-062 Delete all sub-patterns
Are You Sure？Yes：enter No：X
M-063 Restore to default setting
Press Enter to perform operation; Press ESC to quit
Содержание
- Sc500 1790 p.1
- Version 2013 01 p.1
- Computerized control system for square buttonhole machine p.1
- Forewords p.3
- Safety matters for attention p.5
- Installation p.5
- Before checking adjusting and repair any air driven equipment user needs cut off the source of gas and wait for the pressure indicator drop to 0 p.6
- Sewing p.6
- Safety matters for attention computerized control system for square buttonhole machine p.6
- Maintenance inspection p.6
- Table of content p.7
- General information p.11
- General p.11
- Function and specification p.11
- Working environment p.12
- Standardization p.12
- Matters for safe using p.12
- Installation p.12
- Warning and danger p.13
- Others p.13
- Maintenance inspection and repair p.13
- Abandonment p.13
- The preventions on instruction p.14
- Warning p.14
- Operation method p.15
- Sewing list p.16
- Threading needle thread p.17
- Preparation before sewing p.17
- Needles p.17
- Installation of needle p.17
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.17
- Do turn off power when you install p.17
- Installation of bobbin p.18
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.18
- If the bobbin is not in the proper position the shuttle core will move at sewing and thread will be wound to shaft the shape of standard shuttle is different from that of non oil shuttle they cannot be used in common p.18
- In straight buttonhole sewing is different from that of zigzag buttonhole p.19
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.19
- Attention the threading method at slot p.19
- Adjustment of bobbin thread tension p.19
- Threading at bobbin p.19
- When the chemical thread is used please decrease the tension slightly increase the tension when the cotton thread is used p.20
- Installation of knife p.20
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.20
- After adjusting the bobbin thread tension user also needs to check the needle thread tension in the sewing parameters p.20
- Method for adding oil p.22
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.22
- Operating instruction p.23
- Name an p.23
- Description of each part p.23
- Reset release the error p.24
- Minus decrease the value p.24
- First make sure that the set presser type a is the same as that of the presser actually installed p.24
- Esc quit the current interface at data change interface it is for cancelling the change of data p.24
- Enter confirm the changed data p.24
- Common buttons p.24
- Basic operation p.24
- ② select the wanted pattern no p.24
- ① turn on the power p.24
- When the power is on the data input screen is displayed pattern no button b which is marked at present is displayed in the upper section of the screen press button b to select the pattern no the unregistered pattern no will not be displayed p.24
- The buttons for the common operation in each interface are shown at below p.24
- Plus increase the value p.24
- Operating instruction computerized control system for square buttonhole machine p.24
- Number input display the number keyboard and input the number p.24
- Operation of normal pattern p.25
- Operation of continuous sewing p.27
- Operation of cyclic sewing p.29
- Normal pattern sewing p.32
- Function keys p.32
- Pattern registration p.35
- Pattern copy p.37
- Pattern naming p.38
- Threading p.38
- Winding p.39
- Select the type of presser p.40
- Pattern selection p.41
- Sewing shape selection p.42
- Sewing data setting p.44
- Trial sewing p.52
- Direct selection of pattern p.52
- Set needle thread tension p.54
- Operation of counter p.55
- In case of the radial eyelet shape set the bar tacking tension to approximately 120 and make the balance of stitches p.55
- Emergency stop p.56
- Vdt pattern operation p.57
- Display and operation of vdt pattern p.57
- Sewing data of vdt pattern p.58
- Continuous sewing p.59
- Function list p.59
- Selection of continuous sewing pattern p.60
- Edition of continuous sewing pattern p.60
- Edition of continuous sewing p.60
- Continuous sewing pattern registration p.63
- Continuous sewing pattern copy p.64
- Deletion of continuous sewing pattern p.65
- Function list p.68
- Continuous sewing interface p.68
- Trial sewing for continuous sewing p.69
- Function list p.72
- Cyclic sewing p.72
- Pattern registration p.73
- Edition of cyclic sewing p.73
- Pattern copy p.74
- Edition of cyclic sewing pattern p.75
- Selection of cyclic sewing pattern p.75
- Change fabric p.77
- Function list p.78
- Cyclic sewing interface p.78
- Trial sewing at cyclic sewing p.80
- Mode setting p.82
- Function list p.83
- Level 1 parameter setting p.84
- Level 2 parameters setting p.88
- Counter setting p.91
- Functions p.92
- Settings on user management p.93
- Edition of sewing data p.94
- Register pattern to direct button p.95
- Change sewing mode p.95
- 1 adjustment of needle thread trimming p.97
- Test mode p.97
- 3 input signal test method p.98
- 2 adjustment of down thread trimmer p.98
- 4 inspection of lcd display p.99
- 6 output inspection p.100
- 5 correction of touching panel p.100
- 8 continuous running p.101
- 7 speed test p.101
- Operation of keyboard lock p.102
- Brightness adjustment p.102
- Initialization p.104
- Parameter back up restoration p.106
- Operations p.108
- Communication p.108
- About the available data p.108
- Pattern transfer p.109
- Parameter transfer p.111
- Software update p.112
- Information p.114
- Check the maintenance information p.114
- Set the maintenance time p.116
- Method to release the warning p.117
- Via information interface p.118
- Information of production control p.118
- Via sewing interface p.119
- Setting of production control information p.120
- Threading figure p.123
- Warning record p.124
- Running record p.125
- Setting of periodical password p.126
- Warning list p.134
- Appendix 1 p.134
- Hint list p.135
- Common problems and solutions p.137
- Default values of sewing shapes p.140
- Installation size of control box p.149
- Appendix 2 p.149
- Installation size of operation panel p.150
- System diagram p.151
Похожие устройства
-
Aurora А-782DИнструкция к блоку управления -
Aurora А-782DИнструкция по эксплуатации -
Aurora А-781DИнструкция к блоку управления
-
Aurora А-781DИнструкция по эксплуатации
-
Aurora A-9820Руководство по эксплуатации -
Aurora A-1790DРуководство по эксплуатации -
Aurora A-783DИнструкция к блоку управления
-
Aurora A-783DИнструкция по эксплуатации
-
Aurora A-782DИнструкция по эксплуатации -
Aurora A-782DИнструкция к блоку управления -
Aurora A-781DИнструкция к блоку управления -
Aurora A-781DИнструкция по эксплуатации