Home
Главная
Aurora
A-1790D
Панель управления _eng_ Страница: 82

Aurora A-1790D [82/151] Mode setting

Mode Setting Computerized Control System for Square Buttonhole Machine

7 Mode Setting

Press to shift between the Data Input

Interface and Mode Interface (as shown in the right

figure), and the detailed edition and setting can be

carried out under this interface.

Note: For some button, user has to hold to

open them.

Содержание

Sc500 1790 p.1
Version 2013 01 p.1
Computerized control system for square buttonhole machine p.1
Forewords p.3
Safety matters for attention p.5
Installation p.5
Sewing p.6
Safety matters for attention computerized control system for square buttonhole machine p.6
Maintenance inspection p.6
Before checking adjusting and repair any air driven equipment user needs cut off the source of gas and wait for the pressure indicator drop to 0 p.6
Table of content p.7
General information p.11
General p.11
Function and specification p.11
Working environment p.12
Standardization p.12
Matters for safe using p.12
Installation p.12
Warning and danger p.13
Others p.13
Maintenance inspection and repair p.13
Abandonment p.13
Warning p.14
The preventions on instruction p.14
Operation method p.15
Sewing list p.16
Threading needle thread p.17
Preparation before sewing p.17
Needles p.17
Installation of needle p.17
In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.17
Do turn off power when you install p.17
Installation of bobbin p.18
In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.18
If the bobbin is not in the proper position the shuttle core will move at sewing and thread will be wound to shaft the shape of standard shuttle is different from that of non oil shuttle they cannot be used in common p.18
In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.19
Attention the threading method at slot p.19
Adjustment of bobbin thread tension p.19
Threading at bobbin p.19
In straight buttonhole sewing is different from that of zigzag buttonhole p.19
When the chemical thread is used please decrease the tension slightly increase the tension when the cotton thread is used p.20
Installation of knife p.20
In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.20
After adjusting the bobbin thread tension user also needs to check the needle thread tension in the sewing parameters p.20
Method for adding oil p.22
In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.22
Operating instruction p.23
Name an p.23
Description of each part p.23
Reset release the error p.24
First make sure that the set presser type a is the same as that of the presser actually installed p.24
Esc quit the current interface at data change interface it is for cancelling the change of data p.24
Enter confirm the changed data p.24
Common buttons p.24
Basic operation p.24
② select the wanted pattern no p.24
① turn on the power p.24
When the power is on the data input screen is displayed pattern no button b which is marked at present is displayed in the upper section of the screen press button b to select the pattern no the unregistered pattern no will not be displayed p.24
The buttons for the common operation in each interface are shown at below p.24
Plus increase the value p.24
Operating instruction computerized control system for square buttonhole machine p.24
Number input display the number keyboard and input the number p.24
Minus decrease the value p.24
Operation of normal pattern p.25
Operation of continuous sewing p.27
Operation of cyclic sewing p.29
Normal pattern sewing p.32
Function keys p.32
Pattern registration p.35
Pattern copy p.37
Threading p.38
Pattern naming p.38
Winding p.39
Select the type of presser p.40
Pattern selection p.41
Sewing shape selection p.42
Sewing data setting p.44
Trial sewing p.52
Direct selection of pattern p.52
Set needle thread tension p.54
Operation of counter p.55
In case of the radial eyelet shape set the bar tacking tension to approximately 120 and make the balance of stitches p.55
Emergency stop p.56
Vdt pattern operation p.57
Display and operation of vdt pattern p.57
Sewing data of vdt pattern p.58
Function list p.59
Continuous sewing p.59
Selection of continuous sewing pattern p.60
Edition of continuous sewing pattern p.60
Edition of continuous sewing p.60
Continuous sewing pattern registration p.63
Continuous sewing pattern copy p.64
Deletion of continuous sewing pattern p.65
Function list p.68
Continuous sewing interface p.68
Trial sewing for continuous sewing p.69
Function list p.72
Cyclic sewing p.72
Pattern registration p.73
Edition of cyclic sewing p.73
Pattern copy p.74
Selection of cyclic sewing pattern p.75
Edition of cyclic sewing pattern p.75
Change fabric p.77
Function list p.78
Cyclic sewing interface p.78
Trial sewing at cyclic sewing p.80
Mode setting p.82
Function list p.83
Level 1 parameter setting p.84
Level 2 parameters setting p.88
Counter setting p.91
Functions p.92
Settings on user management p.93
Edition of sewing data p.94
Register pattern to direct button p.95
Change sewing mode p.95
Test mode p.97
1 adjustment of needle thread trimming p.97
3 input signal test method p.98
2 adjustment of down thread trimmer p.98
4 inspection of lcd display p.99
6 output inspection p.100
5 correction of touching panel p.100
8 continuous running p.101
7 speed test p.101
Operation of keyboard lock p.102
Brightness adjustment p.102
Initialization p.104
Parameter back up restoration p.106
Operations p.108
Communication p.108
About the available data p.108
Pattern transfer p.109
Parameter transfer p.111
Software update p.112
Information p.114
Check the maintenance information p.114
Set the maintenance time p.116
Method to release the warning p.117
Via information interface p.118
Information of production control p.118
Via sewing interface p.119
Setting of production control information p.120
Threading figure p.123
Warning record p.124
Running record p.125
Setting of periodical password p.126
Warning list p.134
Appendix 1 p.134
Hint list p.135
Common problems and solutions p.137
Default values of sewing shapes p.140
Installation size of control box p.149
Appendix 2 p.149
Installation size of operation panel p.150
System diagram p.151

Aurora A-1790D [82/151] Mode setting

Содержание

Похожие устройства