![Aurora A-1790D — настройка компьютеризированной системы управления швейной машиной [98/151]](/img/pdf.png)
Aurora A-1790D — настройка компьютеризированной системы управления швейной машиной [98/151]
![Aurora A-1790D [98/151] 3 input signal test method](/views2/1495536/page98/bg62.png)
Mode Setting Computerized Control System for Square Buttonhole Machine
88
necessary value, at last press F to return to the origin.
③ Press
to return to the Test Mode Interface
（2）Adjustment of Down Thread Trimmer
① Adjusting Method
In the interface of Test Mode, press
（I02 Down thread
trimming）to enter the adjustment interface of Down thread
trimming (as shown in the right figure):
Down Thread Trimming：
No. Name Range Initial value
A Origin position
B
Releasing position -40~-15 -22
C
Position for trimming -10~10 0
D
Trimming position 40~60 50
E
Initial Position -10~15 0
④ Select the mode position you wish to adjust
Press
G to select the positions (A, B, C, D) for
adjustment, then press the
/ key to adjust the
necessary value, at last press
F to return to the origin
Press
to return to Test Mode Interface.
（3）Input Signal Test Method
In the interface of Test Mode, press (I03 Input
Inspection) to enter the interface of input inspection interface
(as shown in right). Users can confirm the input status of each
switch and sensor.
ON：Turn On
OFF：Turn Off
A：mount of pedal pressed
B：Pedal Sensor
C：Thread-breakage Detection
D：Knife Sensor
Содержание
- Sc500 1790 p.1
- Version 2013 01 p.1
- Computerized control system for square buttonhole machine p.1
- Forewords p.3
- Safety matters for attention p.5
- Installation p.5
- Sewing p.6
- Safety matters for attention computerized control system for square buttonhole machine p.6
- Maintenance inspection p.6
- Before checking adjusting and repair any air driven equipment user needs cut off the source of gas and wait for the pressure indicator drop to 0 p.6
- Table of content p.7
- General information p.11
- General p.11
- Function and specification p.11
- Installation p.12
- Working environment p.12
- Standardization p.12
- Matters for safe using p.12
- Warning and danger p.13
- Others p.13
- Maintenance inspection and repair p.13
- Abandonment p.13
- Warning p.14
- The preventions on instruction p.14
- Operation method p.15
- Sewing list p.16
- Preparation before sewing p.17
- Needles p.17
- Installation of needle p.17
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.17
- Do turn off power when you install p.17
- Threading needle thread p.17
- Installation of bobbin p.18
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.18
- If the bobbin is not in the proper position the shuttle core will move at sewing and thread will be wound to shaft the shape of standard shuttle is different from that of non oil shuttle they cannot be used in common p.18
- Threading at bobbin p.19
- In straight buttonhole sewing is different from that of zigzag buttonhole p.19
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.19
- Attention the threading method at slot p.19
- Adjustment of bobbin thread tension p.19
- When the chemical thread is used please decrease the tension slightly increase the tension when the cotton thread is used p.20
- Installation of knife p.20
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.20
- After adjusting the bobbin thread tension user also needs to check the needle thread tension in the sewing parameters p.20
- Method for adding oil p.22
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.22
- Description of each part p.23
- Operating instruction p.23
- Name an p.23
- Reset release the error p.24
- ② select the wanted pattern no p.24
- ① turn on the power p.24
- When the power is on the data input screen is displayed pattern no button b which is marked at present is displayed in the upper section of the screen press button b to select the pattern no the unregistered pattern no will not be displayed p.24
- The buttons for the common operation in each interface are shown at below p.24
- Plus increase the value p.24
- Operating instruction computerized control system for square buttonhole machine p.24
- Number input display the number keyboard and input the number p.24
- Minus decrease the value p.24
- First make sure that the set presser type a is the same as that of the presser actually installed p.24
- Esc quit the current interface at data change interface it is for cancelling the change of data p.24
- Enter confirm the changed data p.24
- Common buttons p.24
- Basic operation p.24
- Operation of normal pattern p.25
- Operation of continuous sewing p.27
- Operation of cyclic sewing p.29
- Normal pattern sewing p.32
- Function keys p.32
- Pattern registration p.35
- Pattern copy p.37
- Threading p.38
- Pattern naming p.38
- Winding p.39
- Select the type of presser p.40
- Pattern selection p.41
- Sewing shape selection p.42
- Sewing data setting p.44
- Trial sewing p.52
- Direct selection of pattern p.52
- Set needle thread tension p.54
- Operation of counter p.55
- In case of the radial eyelet shape set the bar tacking tension to approximately 120 and make the balance of stitches p.55
- Emergency stop p.56
- Vdt pattern operation p.57
- Display and operation of vdt pattern p.57
- Sewing data of vdt pattern p.58
- Function list p.59
- Continuous sewing p.59
- Selection of continuous sewing pattern p.60
- Edition of continuous sewing pattern p.60
- Edition of continuous sewing p.60
- Continuous sewing pattern registration p.63
- Continuous sewing pattern copy p.64
- Deletion of continuous sewing pattern p.65
- Continuous sewing interface p.68
- Function list p.68
- Trial sewing for continuous sewing p.69
- Function list p.72
- Cyclic sewing p.72
- Pattern registration p.73
- Edition of cyclic sewing p.73
- Pattern copy p.74
- Selection of cyclic sewing pattern p.75
- Edition of cyclic sewing pattern p.75
- Change fabric p.77
- Function list p.78
- Cyclic sewing interface p.78
- Trial sewing at cyclic sewing p.80
- Mode setting p.82
- Function list p.83
- Level 1 parameter setting p.84
- Level 2 parameters setting p.88
- Counter setting p.91
- Functions p.92
- Settings on user management p.93
- Edition of sewing data p.94
- Register pattern to direct button p.95
- Change sewing mode p.95
- Test mode p.97
- 1 adjustment of needle thread trimming p.97
- 3 input signal test method p.98
- 2 adjustment of down thread trimmer p.98
- 4 inspection of lcd display p.99
- 6 output inspection p.100
- 5 correction of touching panel p.100
- 8 continuous running p.101
- 7 speed test p.101
- Operation of keyboard lock p.102
- Brightness adjustment p.102
- Initialization p.104
- Parameter back up restoration p.106
- Operations p.108
- Communication p.108
- About the available data p.108
- Pattern transfer p.109
- Parameter transfer p.111
- Software update p.112
- Information p.114
- Check the maintenance information p.114
- Set the maintenance time p.116
- Method to release the warning p.117
- Via information interface p.118
- Information of production control p.118
- Via sewing interface p.119
- Setting of production control information p.120
- Threading figure p.123
- Warning record p.124
- Running record p.125
- Setting of periodical password p.126
- Warning list p.134
- Appendix 1 p.134
- Hint list p.135
- Common problems and solutions p.137
- Default values of sewing shapes p.140
- Installation size of control box p.149
- Appendix 2 p.149
- Installation size of operation panel p.150
- System diagram p.151
Похожие устройства
-
Aurora А-782DИнструкция к блоку управления -
Aurora А-782DИнструкция по эксплуатации -
Aurora А-781DИнструкция к блоку управления
-
Aurora А-781DИнструкция по эксплуатации
-
Aurora A-9820Руководство по эксплуатации -
Aurora A-1790DРуководство по эксплуатации -
Aurora A-783DИнструкция к блоку управления
-
Aurora A-783DИнструкция по эксплуатации
-
Aurora A-782DИнструкция по эксплуатации -
Aurora A-782DИнструкция к блоку управления -
Aurora A-781DИнструкция к блоку управления -
Aurora A-781DИнструкция по эксплуатации
Узнайте, как правильно настроить компьютеризированную систему управления для швейной машины с квадратным петлителем. Подробные инструкции по регулировке и тестированию.