![Aurora A-1790D Панель управления _eng_ онлайн [139/151] 409087](/img/pdf.png)
Aurora A-1790D Панель управления _eng_ онлайн [139/151] 409087
![Aurora A-1790D Панель управления _eng_ онлайн [139/151] 409087](/views2/1495536/page139/bg8b.png)
Computerized Control System for Square Buttonhole Machine Appendix 1
129
Cable on control box)；
4、 Check the feeding motor and its cable（X13 Port
Cable on control box）, as well as its connection
5、 Enter the Input Test Mode and check the feeding
origin sensor. When the sensor is covered, the
system should display “ON”, while the “OFF” at
being exposed.
E-027 Presser origin detect
error
1、 Check installing position of mechanical devices,
especially the sensor. Generally speaking, the
distance between the sensor and the shielding
sheet should be kept at 3mm；
2、 Check the cable of the presser origin sensor, as
well as its connection;
3、 Check the connection of cable L453 (X9 Port
Cable on control box)；
4、 Check the presser motor and its cable（X12 Port
Cable on control box）, as well as its connection.
5、 Enter the Input Test Mode and check the presser
origin sensor. When the sensor is covered, the
system should display “ON”, while the “OFF” at
being exposed.
E-028 Needle thread
trimming origin detect
error
1、 Check installing position of mechanical devices,
especially the sensor. Make sure no blockage in
the installation. Generally speaking, the distance
between the sensor and the shielding sheet should
be kept at 3mm；
2、 Check the needle-thread-trimming origin sensor.
Enter the Input Test Mode; cover the sensor with
an iron sheet. The system should display ON at
this moment；
3、 Check the connection of cable L453 (X9 Port
Cable on control box)；
4、 Check the connection of cable L451；
5、 Check the motor and its connecting cables. If the
motor has problem, please replace the motor.
E-035 Needle thread
trimming motor error
E-029 Bobbin thread
trimming origin detect
error
1、 Check installing position of mechanical devices,
especially the sensor. Make sure no blockage in
the installation. Generally speaking, the distance
between the sensor and the shielding sheet should
be kept at 3mm；
2、 Check the bobbin-thread-trimming origin sensor.
Enter the Input Test Mode; cover the sensor with
an iron sheet. The system should display ON at
being covered, while “OFF” at being exposed
3、 Check the connection of cable L453 (X9 Port
E-036 Bobbin thread
trimming motor error
Содержание
- Sc500 1790 p.1
- Version 2013 01 p.1
- Computerized control system for square buttonhole machine p.1
- Forewords p.3
- Safety matters for attention p.5
- Installation p.5
- Safety matters for attention computerized control system for square buttonhole machine p.6
- Maintenance inspection p.6
- Before checking adjusting and repair any air driven equipment user needs cut off the source of gas and wait for the pressure indicator drop to 0 p.6
- Sewing p.6
- Table of content p.7
- General information p.11
- General p.11
- Function and specification p.11
- Working environment p.12
- Standardization p.12
- Matters for safe using p.12
- Installation p.12
- Warning and danger p.13
- Others p.13
- Maintenance inspection and repair p.13
- Abandonment p.13
- Warning p.14
- The preventions on instruction p.14
- Operation method p.15
- Sewing list p.16
- Threading needle thread p.17
- Preparation before sewing p.17
- Needles p.17
- Installation of needle p.17
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.17
- Do turn off power when you install p.17
- Installation of bobbin p.18
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.18
- If the bobbin is not in the proper position the shuttle core will move at sewing and thread will be wound to shaft the shape of standard shuttle is different from that of non oil shuttle they cannot be used in common p.18
- Threading at bobbin p.19
- In straight buttonhole sewing is different from that of zigzag buttonhole p.19
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.19
- Attention the threading method at slot p.19
- Adjustment of bobbin thread tension p.19
- After adjusting the bobbin thread tension user also needs to check the needle thread tension in the sewing parameters p.20
- When the chemical thread is used please decrease the tension slightly increase the tension when the cotton thread is used p.20
- Installation of knife p.20
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.20
- Method for adding oil p.22
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.22
- Operating instruction p.23
- Name an p.23
- Description of each part p.23
- Reset release the error p.24
- Operating instruction computerized control system for square buttonhole machine p.24
- Number input display the number keyboard and input the number p.24
- Minus decrease the value p.24
- First make sure that the set presser type a is the same as that of the presser actually installed p.24
- Esc quit the current interface at data change interface it is for cancelling the change of data p.24
- Enter confirm the changed data p.24
- Common buttons p.24
- Basic operation p.24
- ② select the wanted pattern no p.24
- ① turn on the power p.24
- When the power is on the data input screen is displayed pattern no button b which is marked at present is displayed in the upper section of the screen press button b to select the pattern no the unregistered pattern no will not be displayed p.24
- The buttons for the common operation in each interface are shown at below p.24
- Plus increase the value p.24
- Operation of normal pattern p.25
- Operation of continuous sewing p.27
- Operation of cyclic sewing p.29
- Normal pattern sewing p.32
- Function keys p.32
- Pattern registration p.35
- Pattern copy p.37
- Threading p.38
- Pattern naming p.38
- Winding p.39
- Select the type of presser p.40
- Pattern selection p.41
- Sewing shape selection p.42
- Sewing data setting p.44
- Trial sewing p.52
- Direct selection of pattern p.52
- Set needle thread tension p.54
- Operation of counter p.55
- In case of the radial eyelet shape set the bar tacking tension to approximately 120 and make the balance of stitches p.55
- Emergency stop p.56
- Vdt pattern operation p.57
- Display and operation of vdt pattern p.57
- Sewing data of vdt pattern p.58
- Function list p.59
- Continuous sewing p.59
- Edition of continuous sewing p.60
- Selection of continuous sewing pattern p.60
- Edition of continuous sewing pattern p.60
- Continuous sewing pattern registration p.63
- Continuous sewing pattern copy p.64
- Deletion of continuous sewing pattern p.65
- Function list p.68
- Continuous sewing interface p.68
- Trial sewing for continuous sewing p.69
- Function list p.72
- Cyclic sewing p.72
- Pattern registration p.73
- Edition of cyclic sewing p.73
- Pattern copy p.74
- Selection of cyclic sewing pattern p.75
- Edition of cyclic sewing pattern p.75
- Change fabric p.77
- Function list p.78
- Cyclic sewing interface p.78
- Trial sewing at cyclic sewing p.80
- Mode setting p.82
- Function list p.83
- Level 1 parameter setting p.84
- Level 2 parameters setting p.88
- Counter setting p.91
- Functions p.92
- Settings on user management p.93
- Edition of sewing data p.94
- Register pattern to direct button p.95
- Change sewing mode p.95
- Test mode p.97
- 1 adjustment of needle thread trimming p.97
- 2 adjustment of down thread trimmer p.98
- 3 input signal test method p.98
- 4 inspection of lcd display p.99
- 6 output inspection p.100
- 5 correction of touching panel p.100
- 8 continuous running p.101
- 7 speed test p.101
- Operation of keyboard lock p.102
- Brightness adjustment p.102
- Initialization p.104
- Parameter back up restoration p.106
- Operations p.108
- Communication p.108
- About the available data p.108
- Pattern transfer p.109
- Parameter transfer p.111
- Software update p.112
- Information p.114
- Check the maintenance information p.114
- Set the maintenance time p.116
- Method to release the warning p.117
- Via information interface p.118
- Information of production control p.118
- Via sewing interface p.119
- Setting of production control information p.120
- Threading figure p.123
- Warning record p.124
- Running record p.125
- Setting of periodical password p.126
- Warning list p.134
- Appendix 1 p.134
- Hint list p.135
- Common problems and solutions p.137
- Default values of sewing shapes p.140
- Installation size of control box p.149
- Appendix 2 p.149
- Installation size of operation panel p.150
- System diagram p.151
Похожие устройства
-
Aurora А-782DИнструкция к блоку управления -
Aurora А-782DИнструкция по эксплуатации -
Aurora А-781DИнструкция к блоку управления
-
Aurora А-781DИнструкция по эксплуатации
-
Aurora A-9820Руководство по эксплуатации -
Aurora A-1790DРуководство по эксплуатации -
Aurora A-783DИнструкция к блоку управления
-
Aurora A-783DИнструкция по эксплуатации
-
Aurora A-782DИнструкция по эксплуатации -
Aurora A-782DИнструкция к блоку управления -
Aurora A-781DИнструкция к блоку управления -
Aurora A-781DИнструкция по эксплуатации