Home
Главная
IVT
Ударная дрель
ID-710 BMC
Инструкция по эксплуатации Страница: 10

IVT ID-710 BMC [10/72] Auxiliary handle 5 depth ruler 4

Instruction manual

extension cable, while the tool is working. Make sure

you always know where the cable is.

∙ Do not wire a power cable directly into your device

yourself. Instead, take the device to your nearest

authorized Service Center.

∙ To avoid danger, damaged power cord should

be replaced by manufacturer or its agent, or similar

qualied person.

∙ Immediately unplug the tool when its cable is

damaged or cut.

ATTENTION! DANGER OF ELECTRIC

SHOCK!

Consider working area environment. Do not expose

power tools to rain. Do not use power tools in damp

or wet locations. Keep work area well lit and dry. Try

to prevent the device from getting wet or being

exposed to humidity. Do not leave it outside

overnight. Water entering a power tool will increase

the risk of electric shock.

∙ The power supply cable should be checked

regularly and, before using it, make sure the cable is

not damaged or worn out. If the cable is not in good

condition, do not use the appliance; take it to an

authorized service Center.

∙ When tool is used outdoor, only use an extension

cable that is suitable for outdoor use and which is

marked for this specic use. Keep it away from the

working area, from damp, wet or oily surfaces and away

from heat and ammable materials.

∙ Avoid any accidental starting: make sure that the

power switch (if present) is in the «o» position, before

plugging the tool in.

∙ Remove adjusting keys or wrenches before turning

the tool on.

∙ Do not use the tool if the switch does not turn the

tool on or o. Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

WARNING! During the use of certain

power tools, some dust containing

chemicals known to cause cancer,

may occur.

Some of these chemicals are: lead from lead based

paints, crystalline silica from bricks and cement and

other masonry products, arsenic and chromium from

chemically treated lumber and other dangerous

products. If dust is present, your risk from these

exposures varies, depending on how often you do this

type of work. To reduce your exposure to these

chemicals, any time you do pulverulent operations,

work in a well ventilated area and work with

approved safety equipment, such as dust masks

that are specially designed to lter out microscopic

particles.

∙ If the appliance strikes a foreign body, examine the

device for signs of damage and carry out any necessary

repairs before restarting and continuing to work.

∙ If the appliance starts to vibrate abnormally, turn

it o and check for the cause immediately. Vibration is

generally a warning of trouble.

∙ Always switch o the appliance and wait until

the device completely stops whenever you leave

the machine, before carrying out maintenance,

before changing accessories, checking, cleaning,

troubleshooting or working on the appliance.

∙ It is forbidden to move or modify any of the internal

parts of the device.

Specic safety rules

∙ Watch your nger! Wear gloves! Keep your hands

and all your body away from the drilling area and bit.

Keep your second hand on the auxiliary handle.

∙ Wear hear protection when using impact drill.

Exposure to noise can cause hearing loss.

∙ Hold the drill rmly to prevent the loss of control.

∙ Never hold the piece to be drilled in your hands

or across your leg. It’s important to support the work

properly to minimize the body exposure or loss of control.

∙ Never use damaged or incorrect bit.

∙ Use clamps or other practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body is unstable and may

lead to loss of control.

UNPACKING

When unpacking, check to make sure that all

components are included. Refer to the drawings on this

manual. If any parts are missing or broken, please call

an IVT assistance center.

INITIAL OPERATION

Always use the correct supply voltage: the power supply

voltage must match the information quoted on the tool

identication plate.

AUXILIARY HANDLE (5) / DEPTH RULER (4)

For all work with the machine, the auxiliary handle (5)

must be mounted.

When tting the auxiliary handle ensure the hand grip is

loose (screw the handle in an anti-clockwise direction to

loosen) before sliding it over the drill’s shoulder.

IVT ID-710 BMC [10/72] Auxiliary handle 5 depth ruler 4

Содержание

Похожие устройства