![Fluke 712 [5/16] English instruction sheet page 5](/img/pdf.png)
Fluke 712 [5/16] English instruction sheet page 5
![Fluke 712 [5/16] English instruction sheet page 5](/views2/1005462/page5/bg5.png)
712 English Instruction Sheet
Page
5
Simulating an RTD
To simulate an RTD, proceed as follows:
1. Press O to turn on the power.
2. If the calibrator is in input mode (INPUT on the display),
press INPUT OUTPUT once. Make sure the display shows
OUTPUT.
3. Press
R to select the desired RTD type.
4. Connect test leads to the terminals of the RTD measuring
device as shown. Use only the two center outputs (labeled
2W 3W 4W OUTPUT).
NC NC
4W 3W
2W 3W 4W
OUTPUT
INPUT
30V
MAX
30V
MAX
30V
MAX
Sense
connection
(if needed)
Sense
connection
(if needed)
RTD
measurement
device input
kg01f.eps
Содержание
- English instruction sheet page 1 1
- Instruction sheet 1
- Introduction 1
- Rtd calibrator 1
- English instruction sheet page 2 2
- Safety information 2
- W warning 2
- English instruction sheet page 3 3
- Getting acquainted with the calibrator 3
- Press the green o pushbutton to turn the calibrator on and off press the input output pushbutton to select either input measuring or output simulating 3
- English instruction sheet page 4 4
- English instruction sheet page 5 5
- Simulating an rtd 5
- English instruction sheet page 6 6
- Measuring an rtd 6
- Calibration 7
- Cleaning 7
- English instruction sheet page 7 7
- In case of difficulty 7
- Maintenance 7
- English instruction sheet page 8 8
- Replacing the battery 8
- English instruction sheet page 9 9
- Testing and replacing the fuses 9
- W warning 9
- English instruction sheet page 10 10
- English instruction sheet page 11 11
- Replacement parts and accessories 11
- English instruction sheet page 12 12
- English instruction sheet page 13 13
- Ohms specifications 13
- Specifications 13
- Specifications are based on a one year calibration cycle and apply for ambient temperature from 18 c to 28 c unless stated otherwise 13
- Specifications on this instruction sheet apply to the 712 rtd calibrators with serial number 7676001 or above 13
- Accuracy c 14
- Allowable excitation ma 14
- English instruction sheet page 14 14
- Output 14
- Rtd specifications 14
- Rtd type range c f 4 wire 2 wire 3 wire 14
- Since ohms input and output units are available you can use the calibrator for any unsupported rtd type by selecting the ohms range and making manual calculations or referring to tables 14
- English instruction sheet page 15 15
- General specifications 15
- Address correspondence to 16
- English instruction sheet page 16 16
- Fluke corporation fluke europe b v p o box 9090 p o box 1186 everett wa 98206 9090 5602 bd eindhoven u s a the netherlands 16
- How to contact fluke 16
- Or visit fluke s web site at www fluke com 16
- To contact fluke call one of the following telephone numbers 16
- To order accessories receive operating assistance or get the location of the nearest fluke distributor or service center call 16
- To register your product visit register fluke com 16
Похожие устройства
- Digitech BP 200 Инструкция по эксплуатации
- Supra SNB-200 Инструкция по эксплуатации
- LG MH-6646QM Инструкция по эксплуатации
- Hotpoint-Ariston ARSL 105 (CSI).L Инструкция по эксплуатации
- Geo-Fennel FL 55 Multilinner 500050 Инструкция по эксплуатации
- Fluke 714 Инструкция по эксплуатации
- Digitech GNX2 Инструкция по эксплуатации
- Supra SNP-351 Инструкция по эксплуатации
- Belkin F8N136eaKSG Инструкция по эксплуатации
- LG MH-6643C Инструкция по эксплуатации
- Hotpoint-Ariston ARSF 125 CSI.L Инструкция по эксплуатации
- Geo-Fennel FLG 210 A green 291700 Инструкция по эксплуатации
- Digitech GNX3 Инструкция по эксплуатации
- Centurion COMFORT Инструкция по эксплуатации
- Fluke 715 Инструкция по эксплуатации
- LG MH-6642W Инструкция по эксплуатации
- Belkin F8N309cw Инструкция по эксплуатации
- Geo-Fennel FL 240HV Basic Set 244100 Инструкция по эксплуатации
- Centurion ONE TOUCH Инструкция по эксплуатации
- Bosch PPW2201 Инструкция по эксплуатации