Ariston LI 460 A [11/24] Troubleshooting
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Ariston LI 460 A [11/24] Troubleshooting

Ariston LI 460 A [11/24] Troubleshooting
11
EN
Whenever the appliance fails to work, check for a solution from the following list before calling for Technical
Assistance Centre.
Troubleshooting
Problem: Possible causes / Solutions:
The dishwasher does not start.
• The plug has not been inserted into the electrical socket properly, or
there is no power in the house.
• The dishwasher door has not been shut properly.
• A delayed start has been programmed (
see Start-up and use
).
No water drains out from
the dishwasher.
• The dishwasher cycle has not yet finished.
• The water inlet hose is bent (
see Installation
).
• The drain duct is blocked.
• The filter is clogged up with food residues (
see Care and maintenance
).
The dishwasher makes
excessive noise.
• The dishes are rattling against each other or against the sprayer arms.
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not suited to
the hardness of the water (
see Rinse aid and salt
).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
The dishes and glasses are
streaked or have a bluish
tinge.
• The rinse aid dosage is too high (
see Rinse aid and salt
).
The crockery has not been
dried properly.
• The rinse aid has been used up or the dosage is too low (
see Rinse aid
and salt
).
• The rinse aid dispenser setting is not high enough.
• A wash cycle without a drying programme has been selected.
The dishes are not clean.
• The racks are overloaded (
see Loading the racks
).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (
see Wash cycles
).
• An excessive amount of foam has been produced: the detergent has
not been measured out correctly or it is not suitable for use in
dishwashers (
see Start-up and use
).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (
see Care and maintenance
).
• The refined salt level is low (
see Rinse aid and salt
).
The dishwasher does not
take any water in/Tap shut-
off alarm.
(several short beeps are emitted)*
Only available in selected models.
(the second and third WASH
CYCLE indicator lights from the
right flash).
• There is no water in the mains supply.
• The water inlet hose is bent (
see Installation
).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken
when the beeps sounded.* Switch off the machine using the ON/OFF
button, turn on the tap and switch the machine back on after 20
seconds by pressing the same button. Re-programme the machine and
restart the wash cycle.
Foam/Blocked filter alarm
(the second and fourth WASH
CYCLE indicator lights from the
right flash).
• Switch off the appliance by pressing the ON/OFF button.
• There is an excess of foam inside the machine.
• A detergent which is not suitable for use in the dishwasher has been
used;
• The lid on the rinse aid compartment has not been shut correctly.
• Remove any food residues from the filters (
see Care and maintenance
).
Replace the filter assembly correctly and switch the machine back on
by pressing the ON/OFF button. Re-programme the machine and restart
the wash cycle.
Water intake solenoid
valve malfunction alarm
(the third WASH CYCLE indicator
light from the right flashes).
• Switch off the appliance by pressing the ON/OFF button and switch it
back on after a minute. If the alarm continues, shut off the water tap to
eliminate the risk of flooding, remove the plug from the electrical
socket and contact Assistance.

Содержание

Похожие устройства

Troubleshooting H Hotpoint ARISTON Whenever the appliance fails to work check for a solution from the following list before calling for Technical Assistance Centre Problem The dishwasher does not start No water drains out from the dishwasher The dishwasher makes excessive noise Possible causes Solutions The plug has not been inserted into the electrical socket properly or there is no power in the house The dishwasher door has not been shut properly A delayed start has been programmed see Start up and use The dishwasher cycle has not yet finished The water inlet hose is bent see Installation The drain duct is blocked The filter is clogged up with food residues see Care and maintenance The dishes are rattling against each other or against the sprayer arms The dishes and glasses are covered in a white film or limescale deposits The level of the refined salt is low or the dosage setting is not suited to the hardness of the water see Rinse aid and salt The lid on the salt dispenser is not closed properly The rinse aid has been used up or the dosage is too low The crockery is made from non stick material The dishes and glasses are streaked or have a bluish tinge The rinse aid dosage is too high see Rinse aid and salt The crockery has not been dried properly The dishes are not clean The dishwasher does not take any water in Tap shut off alarm several short beeps are emitted Only available in selected models the second and third WASH CYCLE indicator lights from the right flash Foam Blocked filter alarm the second and fourth WASH CYCLE indicator lights from the right flash Water intake solenoid valve malfunction alarm the third WASH CYCLE indicator light from the right flashes The rinse aid has been used up or the dosage is too low see Rinse aid and salt The rinse aid dispenser setting is not high enough A wash cycle without a drying programme has been selected The racks are overloaded see Loading the racks The crockery has not been arranged well The sprayer arms cannot move freely The wash cycle is too gentle see Wash cycles An excessive amount of foam has been produced the detergent has not been measured out correctly or it is not suitable for use in dishwashers see Start up and use The lid on the rinse aid compartment has not been shut correctly The filter is dirty or blocked see Care and maintenance The refined salt level is low see Rinse aid and salt There is no water in the mains supply The water inlet hose is bent see Installation Turn on the tap and the appliance will start after a few minutes The appliance lock has been activated because no action was taken when the beeps sounded Switch off the machine using the ON OFF button turn on the tap and switch the machine back on after 20 seconds by pressing the same button Re programme the machine and restart the wash cycle Switch off the appliance by pressing the ON OFF button There is an excess of foam inside the machine A detergent which is not suitable for use in the dishwasher has been used The lid on the rinse aid compartment has not been shut correctly Remove any food residues from the filters see Care and maintenance Replace the filter assembly correctly and switch the machine back on by pressing the ON OFF button Re programme the machine and restart the wash cycle Switch off the appliance by pressing the ON OFF button and switch it back on after a minute If the alarm continues shut off the water tap to eliminate the risk of flooding remove the plug from the electrical socket and contact Assistance 11

Скачать