Ariston LI 460 A [3/24] H hotpoint
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Ariston LI 460 A [3/24] H hotpoint

Ariston LI 460 A [3/24] H hotpoint
3
EN
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain
duct with a minimum diameter of 4 cm. Alternatively, rest
it over a sink or tub; the free end of the hose should not
remain immersed in water.
The special plastic elbow*
makes it easier to find the
best layout: fix the elbow to
the wall securely in order to
prevent the outlet hose from
moving and spilling the dirty
water.
The part of the hose marked
with the letter A should be
between 40 and 100 cm
above the ground (
see
figure
).
We advise against the use of hose extensions.
Electrical connection
Before inserting the plug into the electrical socket, make
sure that:
• the socket is earthed and complies with current
regulations;
• the socket can withstand the maximum load of the
appliance, which is indicated on the data plate
located on the inside of the door (
see Description of
the appliance
);
• the power supply voltage falls within the values
indicated on the data plate on the inside of the door;
• the socket is compatible with the plug of the
appliance. If this is not the case, ask an authorised
technician to replace the plug (
see Assistance
); do
not use extension cables or multiple sockets.
Once the appliance has been installed, the
power supply cable, the electrical plug and socket
should remain accessible.
If the power supply cable is damaged, it must
be replaced by the manufacturer or its Technical
Assistance Service in order to prevent all potential
hazards. (See Assistance)
The cable should not be bent or compressed.
The Company shall not be held responsible for
any incidents that occur if these regulations are not
observed.
Advice regarding the first wash cycle
After the appliance has been installed, immediately
before running the first wash cycle, completely fill the
salt dispenser with water and add approximately 2 kg of
salt (
see Rinse aid and refined salt
). The water may
overflow: this is normal and is not a cause for concern.
It is also normal that the LOW SALT* indicator light
continues to flash for a few cycles after the salt has been
loaded.
Anti-condensation strip*
After installing the dishwasher, open the door and stick
the adhesive transparent strip under the wooden shelf in
order to protect it from any condensation that may form.
Technical data
* Only available in selected models.
Dimensions
width 44.5 cm
height 82 cm
depth 57 cm
Capacity
9 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
4.3 psi – 145 psi
Power supply
voltage
See appliance data plate
Total absorbed
power
See appliance data plate
Fuse
See appliance data plate
This dishwasher conforms to
the following European
Community Directives:
-73/23/EEC dated 19/02/73
(Low Voltage) and subsequent
modifications
-89/336/EEC dated 03/05/89
(Electromagnetic Compatibility)
and subsequent modifications
-97/17/EC (Labelling)
-2002/96/ CE (
Waste
Electrical and Electronic
Equipment WEEE)
A

Содержание

Похожие устройства

H Hotpoint ARISTON Connecting the water outlet hose Connect the outlet hose without bending it to a drain duct with a minimum diameter of 4 cm Alternatively rest it over a sink or tub the free end of the hose should not remain immersed in water The special plastic elbow makes it easier to find the best layout fix the elbow to the wall securely in order to prevent the outlet hose from moving and spilling the dirty water The part of the hose marked with the letter A should be between 40 and 100 cm above the ground see figure Advice regarding the first wash cycle EN After the appliance has been installed immediately before running the first wash cycle completely fill the salt dispenser with water and add approximately 2 kg of salt see Rinse aid and refined salt The water may overflow this is normal and is not a cause for concern It is also normal that the LOW SALT indicator light continues to flash for a few cycles after the salt has been loaded Anti condensation strip After installing the dishwasher open the door and stick the adhesive transparent strip under the wooden shelf in order to protect it from any condensation that may form Technical data ra We advise against the use of hose extensions Electrical connection Before inserting the plug into the electrical socket make sure that the socket is earthed and complies with current regulations the socket can withstand the maximum load of the appliance which is indicated on the data plate located on the inside of the door see Description of the appliance the power supply voltage falls within the values indicated on the data plate on the inside of the door the socket is compatible with the plug of the appliance If this is not the case ask an authorised technician to replace the plug see Assistance do not use extension cables or multiple sockets ii Once the appliance has been installed the power supply cable the electrical plug and socket should remain accessible W If the power supply cable is damaged it must be replaced by the manufacturer or its Technical Assistance Service in order to prevent all potential hazards See Assistance Dimensions width 44 5 cm height 82 cm depth 57 cm Capacity 9 standard place settings Water supply pressure 0 05 4 1MPa 0 5 e 10 bar 4 3 psi 145 psi Power supply voltage See appliance data plate Total absorbed power See appliance data plate Fuse See appliance data plate Ci This dishwasher conforms to the following European Community Directives 73 23 EEC dated 19 02 73 Low Voltage and subsequent modifications 89 336 EEC dated 03 05 89 Electromagnetic Compatibility and subsequent modifications 97 17 EC Labelling 2002 96 CE Waste Electrical and Electronic Equipment WEEE CT The cable should not be bent or compressed iS The Company shall not be held responsible for any incidents that occur if these regulations are not observed Only available in selected models 3

Скачать