Bosch BGS 42234 [89/200] Filter care
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bosch BGS 42234 [89/200] Filter care

Bosch BGS 42234 [89/200] Filter care
9
Figure
You can use the parking aid on the back of the vacuum
cleaner if you wish to stop vacuuming for a short time.
● After switching off the appliance, slide the hook on the
floor tool into the parking aid.
Figure
When vacuuming stairs, the appliance must be posi-
tioned at the bottom of the stairs. If it does not reach far
enough, the appliance can also be carried using the car-
rying handle or the handle on the dust container.
When the work is done
Figure
● Switch off the appliance.
● Pull out the mains plug.
● Briefly pull on the power cord and then let go. (The
power cord retracts automatically).
Figure
● Unlock the telescopic tube by moving the sliding
switch in the direction of the arrow and slide one tube
into the other.
Figure
To store the appliance, use the storage aid on the under-
side.
a)Stand the appliance up by the hose or the dust con-
tainer handle.
b)Slide the hook on the floor tool into the storage aid.
Emptying the dust container
Figure
In order to achieve the best possible vacuuming results,
the dust container should be emptied after every use or,
at the latest, when dust at one point in the container has
reached the height of the marking.
!
N.B.
The dust container can only be removed when the ap-
pliance is in a horizontal position. Therefore, place the
appliance on the floor to unlock the release button.
Figure
a)Press the release button and pull the dust container
out of the appliance using the handle.
b)Remove the lid from the dust container and empty the
dust container.
c)Put the lid back on the dust container.
d)Remove any dirt which may have been lodged under-
neath the container ejector opening.
e)Insert the dust container in the appliance, so that it
'clicks' audibly into place.
Removal
Figure
● To remove the flexible hose, press the two catches to-
gether and pull the hose out of the air intake opening
of the appliance.
16
17
18
19
15
20
14
13
Figure
a)Telescopic tube without accessory connection:
To release the connection, turn the handle slightly and
pull it out of the telescopic tube.
b)Telescopic tube with accessory connection:
To release the connection, press the locking collar on
the telescopic tube and pull out the handle.
Figure
a)Nozzle without accessory connection:
To release the connection, turn the telescopic tube
slightly and pull it out of the floor tool.
b)Telescopic tube with accessory connection:
To release the connection, press the locking collar and
pull the telescopic tube out of the floor tool.
Filter care
If your appliance is equipped with a filter control, it con-
stantly monitors whether your vacuum cleaner is reach-
ing its optimum power level.
Otherwise, when the suction power noticeably reduces,
you should carry out the following cleaning steps, if re-
quired.
Filter control display
Figure
The display (blue ring) flashes red when the motor pro-
tection filter needs to be cleaned. The appliance is auto-
matically adjusted to the lowest power setting.
Cleaning the motor protection filter
Please switch off the appliance before cleaning the
motor protection filter.
Figure
a)Open the lid of the motor protection filter by pulling
on the locking lever.
b)Remove the motor protection filter with the aid of the
filter handle.
c)Clean the motor protection filter by tapping out the
dirt.
d)If it is very dirty, the motor protection filter should be
rinsed. To do this, remove the foam filter out of the fil-
ter frame. Then allow the filter to dry completely.
c)After cleaning the motor protection filter, reinsert it
into the appliance and close the lid of the motor pro-
tection filter.
!
N.B.
The lid can only be closed when a filter has been in-
serted.
If, after cleaning the motor protection filter, the control
display is still flashing red, please check whether the noz-
zle, suction pipe or flexible hose are blocked. This can
also trigger the filter control display.
Cleaning the fluff filter
If the control display continues to flash red, despite the
nozzle, pipe and hose being clear, the fluff filter needs
to be cleaned.
21
22
23*
24
*
Dependent on model

Содержание

Похожие устройства

Скачать