![Griven GRAPH-i-DOT [12/12] Al4700 graph i dot rev 1 0](/img/pdf.png)
Griven GRAPH-i-DOT [12/12] Al4700 graph i dot rev 1 0
![Griven GRAPH-i-DOT [12/12] Al4700 graph i dot rev 1 0](/views2/1700066/page12/bgc.png)
Содержание
- Al4700 1
- Graph i dot 1
- Page 1 of 12 1
- Rev 1 0 date 11 01 2019 1
- User manual 1
- Al4700 graph i dot rev 1 0 2
- Important notices avvertimenti importanti 2
- Page 2 of 12 2
- Connecting graph i dot to the start line kit al4703 3
- Al4700 graph i dot rev 1 0 4
- Connecting graph i dot to the power supply kit al4704 4
- Copyright 4
- Description 4
- Griven s r l world lighting challenge 4
- Page 4 of 12 4
- Revision 4
- The kit contains 1 2 halves plastic enclosure with holes for eventual fixing 3 ip67 thermo shrinking terminal caps green tip 2 ip67 thermo shrinking terminal caps red tip 4
- Weight 4
- Al4700 graph i dot rev 1 0 5
- Page 5 of 12 5
- Typical system diagram 5
- Al4700 graph i dot rev 1 0 6
- Place with care the cables into the lower half of the enclosure fix the joint caps in order to take up as little less space as possible 6
- Put the upper half over the lower half of the enclosure press until the lock of the clips if you feel high resistance do not force but check the accomodation of the cables inside 6
- Al4700 graph i dot rev 1 0 7
- Insert the end of the flat cable inside the lower half of the terminal enclosure fill with silicone rtv and then close the enclosu re with the other half let it dry before fixing it on to a surface 7
- Page 7 of 12 7
- Remove the faulty dot saving the more cable lenght possible 7
- Replacing a faulty graph i dot kit al4705 7
- Silicone rtv 7
- Split the cables and strip the ends of the cables warning in order to respect the original distance between the single dots we reccomend to carefully take the adequate measurements and eventually correct cable lenghts before proceeding in making the joints 7
- Al4700 graph i dot rev 1 0 8
- Gnd a b ad vcc 8
- Lay down the joint into the lower half of the enclosure put the upper half over the lower half of the enclosure press until the lock of the clips 8
- Page 8 of 12 8
- Put before soldering each joint the thermo shrinking sleeves solder all the joints cover them with the sleeves then make them adhere to the cables by blowing hot air coming from a thermoblower pay attention to the polarities before this last operation 8
- Addressing the graph i dot chain 9
- Al4700 graph i dot rev 1 0 10
- Installation directions 10
- Installation on a surface 10
- Installation on a surface by using optional accessory al4708 10
- M4 x 12 screws 10
- Max ø screws 4 mm 10
- Al4700 graph i dot rev 1 0 11
- Installation on a rope by using optional accessory al4708 11
- Al4700 graph i dot rev 1 0 12
Похожие устройства
- Daikin FXCQ80AVEB Инструкция по монтажу
- Daikin FXCQ80AVEB Руководство по эксплуатации
- Daikin FXCQ80AVEB Технические данные
- Brayer BR1007 Инструкция по эксплуатации
- Daikin FXCQ125AVEB Руководство по эксплуатации
- Daikin FXCQ125AVEB Инструкция по монтажу
- Daikin FXCQ125AVEB Технические данные
- Griven GRAPH-i-CELL Руководство пользователя Start Line Box _итал., англ._
- Griven GRAPH-i-CELL Руководство пользователя Repower Box _итал., англ._
- Griven GRAPH-i-CELL Схема коммутации
- Griven GRAPH-i-CELL Руководство пользователя Electronic Driver _итал., англ._
- Griven GRAPH-i-CELL Руководство пользователя Graph_i_Cell _итал., англ._
- Griven GRAPH-i-CELL Чертеж с размерами Electronic Driver
- Griven GRAPH-i-CELL Чертеж с размерами Graph_i_Cell
- Griven GRAPH-i-CELL Чертеж с размерами Start Line Box
- Griven GRAPH-i-CELL Чертеж с размерами Repower Box
- Griven GRAPH-i-SPOT Руководство пользователя Start Line Box _итал., англ._
- Griven GRAPH-i-SPOT Руководство пользователя Repower Box _итал., англ._
- Griven GRAPH-i-SPOT Страницы из каталога _англ._
- Griven GRAPH-i-SPOT Руководство пользователя Electronic Driver _итал., англ._