![Planet IDL-4801 Инструкция по эксплуатации онлайн [519/707] 66120](/img/pdf.png)
Planet IDL-4801 Инструкция по эксплуатации онлайн [519/707] 66120
![Planet IDL-4800 Инструкция по эксплуатации онлайн [519/707] 66117](/views2/1071613/page519/bg207.png)
IP DSLAM
519
this instance is created
L2 type
This Parameter represents the L2 type used
Encap Type
This Parameter specifies the encapsulation type of the aal5 VC
corresponding the bridge port for which this instance is created
DRA Add Op82 To
Unicast
This field specifies whether Option 82 is to be added to DHCP
Unicast packets or not. If enabled Option 82 will be added to
DHCP Unicast Packets and when disabled, it will not be added.
References:
DHCP Relay Agent commands
5.20.3 Dra stats entry Commands
5.20.3.1 Get dra stats entry
Description:
Use this command to get.
Command Syntax:
get dra stats entry [portid <portid-val>] [vlan <vlan-val>]
5.20.3.2 Reset dra stats entry
Description:
Use this command to reset.
Command Syntax:
get dra stats entry [portid <portid-val>] [vlan <vlan-val>]
Parameters:
Name Description
portid <portid-val>
Bridge port identifier
Type: Reset -- Mandatory
Get -- Optional
Valid values: 1 - 194
vlan <vlan-val>
VLAN identifier. In case of stacked mode this is virtual VLAN
Type: Reset -- Mandatory
Get -- Optional
Valid values: 1 - 4095
Содержание
- Disabling 802 x globally 04 23
- Disabling multiple hosts 05 23
- Enabling 802 x globally 04 23
- Enabling and initializing 802 x authentication individual ports 04 23
- Enabling multiple hosts 05 23
- Specifying the radius key 703 configuring 802 x authentication 703 23
- X protocol over ip dslam 705 appendix d what s ip dslam 706 23
- Introduction 24
- Package contents 24
- Access control list by mac and ip address 25
- Application 25
- Base t idl 2400 idl 4800 or 1000base lx idl 2401 idl 4801 uplink interface 25
- Dmt data rate downstream 32 kbps up to 25 mbps upstream 32 kbps up to 1mbps 25
- Features 25
- Firmware upgradeable via ftp or tftp 25
- K mac address 256 multicast mac address support 25
- Local rs 232 cli and ethernet snmp telnet management 25
- Microsoft windows based gui management 25
- Port or 48 port adsl adsl2 adsl2 subscriber interface with build in pots splitter 25
- Stackable support 25
- Static vlan and port based vlan 25
- The planet idl series offer the benefit of high performance to central office co location and mtu multi tenant unit mdu multi dwelling unit markets it provides broadband data service over existing copper wires without affecting the conventional voice service by 24 48 subscriber ports with built in pots splitter a planet ip dslam is the perfect solution for nsp a cost effective but high value centrally management capability 25
- Traffic bandwidth management by mac and ip address 25
- Traffic prioritization 802 p 25
- Vlan mac ip filtering 25
- Outlook 26
- Front panel 27
- Front panel the front panels of idl series are shown below 27
- Idl 2400 idl 2400 27
- Idl 2401 idl 2401 27
- Idl 4800 idl 4800 27
- Idl 4801 idl 4801 27
- Led color led description 27
- Led definition 27
- Idl 2400 2401 idl 2400 2401 28
- Idl 4800 4801 idl 4800 4801 28
- Port definition 28
- Port port description 28
- Rear panel 28
- Rear panel the rear panels of idl series are shown below 28
- Hardware specifications 29
- Technical specifications 29
- Software specifications 30
- Installation 32
- Safety instruction 32
- Hardware installation 33
- Rear panel connection 33
- System requirements 33
- Front panel connection 34
- Idl manager installation 35
- Installing idl manager 35
- System requirements 35
- Starting idl manager 37
- Idl manager functions 38
- Logout 38
- Session 38
- Agent desktop 53
- Idl manager management 53
- Active function management windows 55
- Default setting 56
- On system information from the function list window the window appears as follows 57
- System information 57
- This section describes how to get and input the information of the ip dslam double click 57
- Current event 58
- Archived this window allows you to browse the expired records which can be configured in the 60
- Environment window click on the tab of archived that will bring the archived screen to 60
- Exit the window 60
- Front as the following figure shown click on 60
- To clear all records or 60
- System 61
- Allow user to view and modify vlan configuration double click on vlan from the function list window the vlan configuration window appears as follows 62
- Configuration 62
- This section describes how to configure the ip dslam by selecting configuration from function list window 62
- A select the vlan to view or modify by using the vlan id drop down list b use egress pvc and untagged pvc drop down list to set the specified dsl port s egress pvc and untagged pvc 63
- Allow user to view and modify ethernet configuration double click on ethernet from the function list window the ethernet configuration window appears as follows 63
- C click on 63
- Ethernet 63
- To close the vlan configuration window 63
- To submit your settings or click on 63
- Line profile if to configure line profile double click on line profile from the function list window the line profile configuration window appears 65
- Profile allow users to configure line profile and alarm profile 65
- This section describes how to configure dsl settings by selecting dsl from function list window 65
- A choose the port to configure from the dsl port drop down list b configure the administration status as up or down c choose a line profile from the line profile name drop down list if to configure a 68
- An alarm profile click on 68
- And then pvc2 appears and then users can 68
- E click on 68
- F if to create new pvc click on 68
- Line profile click on 68
- Set perimeters via pvc2 after that click on 68
- To activate the alarm profile configuration window if necessary modify values of specified pvc including vpi vci admin status learning status sticky status pvid accepted frame type and ingress filter and priority 68
- To activate the line profile configuration window d choose an alarm profile from the alarm profile name drop down list if to configure 68
- To close the fmbridgeport window 68
- To submit or click on 68
- To submit your setting 68
- Dsl pm 70
- Dslam double click on physical layer info from the function list window the physical layer info window appears 70
- Physical layer info allow users to view the physical layer information of a specified dsl port from the ip 70
- This section describes how to utilize dsl performance management by selecting dsl pm from function list window 70
- Channel layer info allow users to view the channel layer information of a specified dsl port from the ip 71
- Dslam double click on channel layer info from the function list window the channel layer info window appears 71
- Info click on 71
- Select the port id from the dsl port drop down list to view a specified dsl s physical layer 71
- Select the port id from the dsl port drop down list view a specified dsl s channel layer 71
- To close the window 71
- Application note 72
- Basic configuration 72
- Dest nvram cfg factorydef fd cfg is the path of firmware file located on ip dslam 76
- Note the file name to download could be different from fd cfg but do not change the path 76
- Step 12 input list to show the path and s w information 76
- Step 13 input remove fname nvram cfg factorydef fd cfg version 1 to remove the obsolete fd cfg file 76
- Step 14 input download src fd cfg dest nvram cfg factorydef fd cfg ip 192 68 00 6 to download config file fd cfg from server pc to ip dslam 76
- How to create myconfig cfg myconfig cfg is a txt file that ensures all commands be executed at once 4 shows the format of myconfig cfg if there are many configurations you would like to execute then you can write all commands into myconfig cfg and then execute it at once be note to save commit to ip dslam if this would be executed after rebooting required of equipment tftp server tftpd32 78
- Tftp server configuration 78
- Myconfig cfg configuration 79
- Format of myconfig cfg 80
- Be noted that gsstandard gstxpoweratten and gsannextype must be modified at the same time 3 frequently used commands are listed below for your reference aturintlmaxtxrate 0x7d000 atucgsannextype adsl2 atucgsstandard adsl2plus atucgstxpoweratten 0 atucmaxintldelay 1 atucfastmintxrate 0xfa00 aturfastmintxrate 0x7d00 atucgsannextype annexa atucgsstandard glite atucgstxpoweratten 0 type fastonly atucrateadaptation fixed 81
- Line rate configuration this section describes how to configure the transmission rate manually via cli before configuration see follows 1 input the line rate by using hexadecimal values following tables shows the hexadecimal values that are frequently used 81
- Configuration step 1 82
- Disable the dsl port that you want to re configure its transmission rate 82
- Set the line rate you need 83
- Step 2 83
- Enable the port 86
- Step 3 86
- Option 2 set up the system time manually step 1 view the system information 88
- Step 3 confirm the status of sntp client 88
- Step 2 get sntp parameter definitions 89
- Step 3 set up system time and time zone 89
- Configuration step 1 create a vlan group no and assign to bridge port 1 adsl port 1 pvc 8 81 and 385 eth 0 91
- Step 2 set bridge port 1 adsl port 1 pvc 8 81 as pvid 2 91
- Vlan configuration ip series support port based vlan and group vlan this section describes how to create two vlan groups vlan id 2 and 3 adsl ports 1 2 pvc 8 81 will join in vlan group 2 and create new pvc 8 82 for adsl1 and assign this pvc to vlan group 3 besides uplink interface eth 0 will join vlan group 2 3 as trunk interface 91
- Step 3 show current vlan status 92
- Create eoa interface 93
- Step 4 create new pvc 8 82 in adsl port 1 create atm vc and aal5 interface 93
- Step 5 create a new bridge port 49 and maps to new created pvc 8 82 in adsl port 1 93
- Step 6 create a new vlan group no and assign to bridge port 49 adsl port 1 pvc 8 82 and 385 eth 0 94
- Step 7 set bridge port 49 adsl port 1 pvc 8 82 as pvid 3 94
- Step 8 modify the vlan group 2 and add bridge port 2 adsl port 2 pvc 8 81 95
- Step 9 add port3 to vlan2 use vlanid index 95
- Set vpi vci is 0 35 96
- Step 10 modify the vlan from 8 81 to 0 35 set the aal5 strat number is 0 96
- Step 11 set aal5 as enable 97
- Configuration step 1 set adsl port12 disable 98
- Modify the downstream upstream rate 98
- Step 2 set adsl port 12 interleave mode downstream 512k the value is hex so you must conversion to decimal 99
- Step 3 set adsl port12 interleave mode upstream 512k the value is hex so you must conversion to decimal 101
- Step 4 set adsl port12 enable 104
- Configuration step 1 create snmp community 105
- Enable snmp function 105
- Setp 2 create snmp host 105
- Setp 3 create snmp traphost 105
- About cli administration 106
- System administration with cli 106
- Glossary of terms and acronyms this section contains a brief list of selected acronyms 107
- Pairs and can vary from 0 to n they indicate the parameter values passed to a cli command ifname aal5 0 portid 20 are examples of tag value pairs 107
- This is the fourth keyword of a cli command it indicates the sub group of a cli command intf is an example of this keyword 107
- This is the third keyword of a cli command it indicates the sub group of a cli command port is an example of this keyword 107
- Cli command brief description cli command action list 108
- Categories of the cli commands 109
- Bridge port accessprio commands 114
- Example get bridge port accessprio portid 1 regenprio 1 114
- Get bridge port accessprio description use this command to get 114
- Output field 114
- Output portid 1 regenprio 1 acesspriority 0 114
- P commands 114
- Parameters 114
- References bridge port commands 114
- Bridge port prioinfo commands 115
- Example get bridge port prioinfo portid 1 115
- Get bridge port prioinfo description use this command to get 115
- Modify bridge port prioinfo 5 modify bridge port prioinfo description use this command to modify 115
- Parameters parameters 115
- Output field 116
- Output portid 1 defaultpriority 1 numtrafficclass 3 defaultsvpriority 1 116
- References bridge port commands 116
- 5 modify bridge port trfclassmap description use this command to modify 117
- Bridge port trfclassmap commands 117
- Get bridge port trfclassmap description use this command to get 117
- Parameters 117
- Example get bridge port trfclassmap portid 1 regenprio 1 118
- Output field 118
- Output portid 1 regenprio 1 trafficclass 2 118
- References bridge port commands 118
- Abond commands 121
- Enable disable 122
- Modify abond group intf description use this command to modify 122
- Parameters 122
- Example create abond group intf ifname abond 0 groupid 1 minaggrrateupstrm 5 minaggrratednstrm 5 diffdelaytolupstrm 0 diffdelaytoldnstrm 0 asmprotocol disable sidformat eightbitsid maxrxbitrateratio 2 linkhecthrshld 1 numoflinksupforgrpup one asmirlthreshold 0 maxatmportusrate 0 124
- Output verbose mode on entry created ifname abond 0 groupid 1 minaggrrateupstrm 5 minaggrratednstrm 5 diffdelaytolupstrm 4 diffdelaytoldnstrm 4 asmprotocol disable sidformat eightbitsid maxrxbitrateratio 2 linkhecthreshold 1 ctrlvpi 0 ctrlvci 0 nooflinksupforgrpup one asmirlthreshold 0 maxatmportusrate 0 oper status up admin status enable verbose mode off 124
- Output fields 125
- Grpfailurereason minratenotachievedupanddn asmrxcrcerrorcount 10 127
- Output fields 127
- Example create abond link entry ifname abond 0 lowif dsl 0 txlinkadminstatus enable rxlinkadminstatus enable asmrxgroupintf abond 0 asmrxlinkindex dsl 0 129
- Parameters 129
- Output fields 130
- Output verbose mode on entry created ifname abond 0 lowif dsl 0 asmrxgroupintf abond 0 asmrxlinkindex dsl 0 txlinkadminstatus enable rxlinkadminstatus enable txlinkoperstatus disable rxlinkoperstatus disable asmtxlinkstatus selectedtocarrybondingtraffic asmrxlinkstatus selectedtocarrybondingtraffic verbose mode off entry created 130
- Aggregation commands 132
- Parameters 135
- Example create aggr intf ifname aggr 0 ip 172 5 00 00 mask 255 55 usedhcp false mgmtvlanid 2 mgmtsvlanid 2 priority 2 enable 136
- Output fields 137
- Output verbose mode on entry created interface index aggr 0 ip address 172 5 00 00 mask 255 55 usedhcp false mgmt vlan index 2 mgmt s vlan index 2 tagged mgmt pdu prio 2 oper status up admin status enable verbose mode off entry created 137
- Aggrtype static lacp 139
- Delete lacp aggr description use this command to delete 139
- Delete lacp aggr description use this command to modify 139
- Parameters 139
- Example create lacp aggr aggrifname aggr 0 actorsystemprio 2 actoradminkey 1000 collectormaxdelay 2 aggrtype static 140
- Output fields 140
- Output verbose mode on entry created aggr ifname aggr 0 mac address 23 45 67 89 00 01 aggregate true actor sys priority 2 partner sys priority 2 actor sys id 23 45 67 89 00 01 partner sys id 23 45 67 89 00 01 actor oper key 10 partner oper key 2 actor admin key 1000 collector max delay 2 aggregation type static verbose mode off entry created 140
- Cautions lacp aggregator creation shall fail if aggregator interface is not created lacp aggregator shall not be created if redundancy aggregator is created for an aggregator interface 141
- References references create aggr intf get aggr intf 141
- Actor admin key 1000 partner admin key 2 144
- Actor oper key 10 partner oper key 2 144
- Actor port 2 partner oper sys priority 2 144
- Actor port priority 1 partner admin port priority 1 144
- Actor system id 23 45 67 89 00 01 partner admin sys priority 2 144
- Actor system priority 2 partner oper port priority 1 144
- Aggregation status enable lacp packetsprio 2 144
- Attached agg id aggr 0 selected agg id aggr 0 144
- Example get lacp aggrport info ifname eth 0 144
- Interface eth 0 port is aggregate true 144
- Output 144
- Output fields 144
- Partner admin sys id 23 45 67 89 00 01 partner admin port 1 144
- Partner oper sys id 23 45 67 89 00 01 partner oper port 1 144
- Port actor admin state distrib 144
- Port actor oper state default 144
- Port partner admin state activity 144
- Port partner oper state default 144
- References lacp aggrport list lacp aggrport stats 145
- Command syntax get rdncy aggr info ifname interface name 148
- Description use this command to get 148
- Get rdncy aggr info 148
- Output fields 148
- Redundancy aggr info commands 148
- References lacp aggr lacp aggrport list lacp aggrport info 148
- Example create rdncy aggr info ifname aggr 0 revdistrib disable fallback disable 150
- Output fields 150
- Output verbose mode on entry created interface index aggr 0 reverse distribution disable fallback disable 150
- Verbose mode off entry created 150
- Example get rdncy aggr stats ifname aggr 0 153
- Output fields 153
- Output interface index aggr 0 collapse count 1 decollapse count 1 last collapse time mm dd yyyy hh mm ss 04 21 2003 12 23 34 last de collapse time mm dd yyyy hh mm ss 04 21 2003 12 23 34 153
- Parameters 153
- Aal5 vc statistics commands 154
- Atm commands 154
- Description use this command to get aal5 vc statistics 154
- Example get atm aal5 stats ifname aal5 0 154
- Get atm aal5 stats 154
- Output fields 154
- Output low ifname atm 0 vc ifname aal5 0 vpi 0 vci 1 tx frames count 100 rx frames count 85 tx bytes count 1535 rx bytes count 1200 crc errors count 0 oversized sdu 0 154
- Parameters 154
- Atm port and statistics related commands atm oam loopback commands 156
- Example get oam cc vc ifname aal5 0 156
- Output fields 156
- Output ifname mode sourceoperstatus sinkoperstatus initiator aal5 0 manual activated loc self 156
- References atm vc related commands 156
- Atmtransporttype cell packet enable disable 159
- Delete atm port 159
- Description use this command to delete 159
- Description use this command to modify 159
- Modify atm port 159
- Parameters 159
- Example create atm port ifname atm 0 lowif dsl 0 maxvc 5 maxvpibits 6 maxvcibits 12s oamsrc 0xffffffffffffffffffffffffffffffff orl 3000 trfclassprofileid 3 profilename gold ctlpktinstid 1 atmtransporttype cell mirrormode mirror enable 161
- Output output verbose mode on entry created ifname atm 0 lowifname dsl 0 maxvccs 5 maxvpibits 6 maxvcibits 12 oamsrc 0xffffffffffffffffffffffffffffffff orl kbps 3000 unknownvpi 35 unknownvci 35 profilename gold current output rate 64 trfclassprofileid 3 ctl pkts instance id 1 atm transport type cell mirror mode mirror oper status up admin status enable 161
- Output fields output fields 162
- Verbose mode off entry created 162
- Description use this command to modify atm vc parameters 164
- Modify atm vc intf 164
- Parameters 164
- Vcmux llcmux auto ethernet mgmtmode data mgmt dataandmgmt raw autosupportedprot none pppoa eoa ipoa autovcmuxforcedprot none pppoa eoa ipoa autosensetriggertype dynamic opstatechange 164
- Example create atm vc intf ifname aal5 0 lowif atm 0 vpi 10 vci 10 enable aal5 pvc a5txsize 1536 a5rxsize 1536 llcmux mgmtmode data autosupportedprot pppoa eoa autovcmuxforcedprot pppoa autosensetriggertype dynamic ctlpktgroupid none 167
- Output verbose mode on entry created vc ifname aal5 0 low ifname atm 0 vpi 0 vci 35 admin status up oper status down aal5 tx size 1536 aal5 rx size 1536 aal type aal5 aal5 encap llcmux channel interleaved last change sec 0 mgmtmode data row status active 167
- Output fields 168
- Vc type pvc vc topology point to point max simultaneous protocol 1 auto status disable auto supported protocol pppoa eoa auto vc mux forced protocol none auto sense trigger type dynamic auto curr sensed encaps typee none ctl pkts group id none auto supported protocol pppoa eoa 168
- Caution the specified lower interface should exist please refer to the create atm port command 170
- References atm interface commands atm statistics commands atm oam commands atm vc statistics commands 170
- Atm vc statistics commands 171
- Description use this command to get statistical information about a specific or all atm virtual circuits 171
- Example get atm vc stats ifname aal5 0 171
- Get atm vc stats 171
- Output fields 171
- Output low ifname atm 0 vc ifname aal5 0 vpi 1 vci 1 total tx cells count 250 total rx cells count 20 clpi 0 rx cells count 10 rx pkts rejected count 0 171
- Parameters 171
- References other atm vc related commands oam lpbk command atm port related commands atm statistics related commands 172
- 5 delete bridge forwarding description use this command to delete 173
- Bridge forwarding commands 173
- Bridging commands 173
- Get bridge forwarding description use this command to get 173
- Parameters 173
- Example get bridge forwarding vlanid 10 macaddr 02 2e 22 3d 44 56 174
- Output fields 174
- Output mac addr portid vlanid status 02 2e 22 3d 44 56 10 10 learned 174
- Example get bridge port forwarding portid 10 vlanid 10 macaddr 02 03 ee 34 55 66 178
- Output fields 178
- Output port id 10 vlan id 10 mac addr 02 03 ee 34 55 66 status mgmt 178
- Example create bridge port map portid 2 ifname eoa 0 180
- Output fields 180
- Output verbose mode on entry created port id 2 interface index eoa 0 verbose mode off entry created 180
- Parameters 180
- Example create bridge port intf ifname eth 0 portid 10 maxucast 10 learning enable stickystatus enable status enable fdbmodify disable aclglbdenyapply disable aclglbtrackapply disable proxyarpstatus enable arptstatus enable darpstatus enable porttype trusted 185
- Output fields 186
- Output port id 10 max unicast addresses 10 learning status enable port oper status disable port admin status disable sticky status enable fdb modify disable acl global deny apply disable acl global track apply disable proxyarpstatus enable sensed ifindex eoa 1 arptstatus enable directed arp status enable port type trusted 186
- Parameters 190
- Example create bridge static mcast vlanid 7 mcastaddr 00 30 4f 00 00 01 recvport 0 egressports 10 forbidegressports 20 skip 1 191
- Output fields 191
- Output verbose mode on entry created vlan index 7 mcast address 00 30 4f 00 00 01 egress ports 10 forbidden egress ports 20 verbose mode off entry created 191
- Example create bridge static ucast vlanid 1 ucastaddr 1 1 1 1 1 1 recvport 0 portid 2 status 1 cfgmode config 193
- Modify bridge static ucast description use this command to modify 193
- Parameters 193
- Bridge tbg traps commands 195
- Command syntax get bridge tbg traps 5 0 modify bridge tbg traps description use this command to modify 195
- Command syntax modify bridge tbg traps bindingstatus enable disable fdbtrapstatus enable disable vmactrapstatus enable disable traploss ok notok 195
- Get bridge tbg traps description use this command to get 195
- Parameters 195
- Example get bridge tbg traps 196
- Output binding status changed trap enable forwarding table trap enable virtual mac trap enable forwarding table trap loss ok 196
- Output fields 196
- References bridge commands 196
- 5 1 modify garp port info description use this command to modify 197
- Example get garp port info 197
- Garp port info commands 197
- Get garp port info description use this command to get 197
- Parameters 197
- Command syntax reset stp stats parameters 199
- Reset stp stats description use this command to reset stp global statistics 199
- Example modify stp info priority 0x20 maxage 25 htime 5 fdelay 20 enable 200
- Output fields 200
- Output protocol spec ieee 8021d priority 0x20 top changes 1 curr top age sec 35 desig root 00 30 4f 10 5a 6c db 20 root cost 0 root port none hold time sec 1 br max age sec 25 curr max age sec 20 br hello time sec 5 curr hello time sec 2 br fwd delay sec 20 curr fwd delay sec 15 stp status enable verbose mode off set done 200
- References get stp info command stp port related commands 201
- Caution the specified interface should be an existing bridge interface 204
- Output fields 204
- References bridge port intf command 204
- Output fields 208
- References bridge port commands bridge port stats commands ethernet commands 209
- 5 modify bridge mcast fwdall description use this command to modify 210
- Bridge mcast forwarding commands 210
- Bridge multicast commands 210
- Get bridge mcast forwarding description use this command to get 210
- Parameters 210
- Example get bridge mcast fwdall vlanid 1 211
- Output fields 211
- Output vlan index 1 forward all ports 34 forward all static ports 1 2 3 5 forward all forbidden ports 4 9 10 11 211
- Example get bridge mcast forwarding vlanid 1 macaddr 00 30 4f 00 08 01 213
- Output fields 213
- Output vlan index 1 mac address 00 30 4f 00 08 01 egress ports 1 2 group learnt 1 213
- References bridge static multicast 213
- 5 modify bridge mcast fwdunreg description syntax use this command to modify 214
- Bridge mcast fwdunreg commands 214
- Get bridge mcast fwdunreg description use this command to get 214
- Parameters 214
- Example get bridge mcast fwdunreg vlanid 1 215
- Output fields 215
- Output vlan index 1 forward unregistered ports 45 forward unregistered static ports 1 2 3 6 forward unregistered forbidden ports 4 9 10 215
- Modify bridge static mcast description use this command is used to modify 217
- Parameters 217
- Example create bridge static mcast vlanid 7 mcastaddr 00 30 4f 00 00 01 egressports 10 forbidegressports 20 218
- Output fields 218
- Output verbose mode on entry created vlan index 7 mcast address 00 30 4f 00 00 01 egress ports 10 forbidden egress ports 20 verbose mode off entry created 218
- Dhcp commands 220
- Output fields 222
- References dhcp client info related commands 222
- Rel sent 0 nacks rcvd 0 inform sent 0 invalid rcvd 0 222
- Dsl commands 223
- Example get adsl alarm profile ifname dsl 0 226
- Output ifname dsl 0 adsl atuc configuration 226
- Thresh 15min lofs sec 10 thresh 15min loss sec 20 thresh 15min lols sec 30 thresh 15min lprs sec 50 thresh 15min ess sec 40 thresh fast rate up bps 70 thresh intl rate up bps 30 thresh fast rate down bps 10 thresh intl rate down bps 30 init fail trap true opstatetrapenable false powermgmttrapenable true adsl atur configuration thresh 15min lofs sec 10 thresh 15min loss sec 10 thresh 15min lprs sec 10 thresh 15min ess sec 10 thresh fast rate up bps 10 thresh intl rate up bps 10 thresh fast rate down bps 10 thresh intl rate down bps 10 226
- Output fields 227
- References adsl commands 228
- References adsl commands 235
- Adsl atuc channel commands 236
- Example get adsl atuc channel ifname dsli 0 236
- Get adsl atuc channel description use this command to get 236
- Output fields 236
- Output ifname dsli 0 interleave delay ms 20 curr tx rate bps 80 prev tx rate bps 40 crc block length byte 90 gs curr atm status noatmdefect gssymbolsperrsword 10 gsrsdepth 20 gsredundantbytesperrscode 100 atucchanperfatmcd 10 atucchanperfatmcu 10 atucchangsinpdn 10 atucchangsl0dn 10 atucchangsm0dn 10 atucchangst0dn 10 atucchangsb0dn 10 236
- Parameters 236
- Output fields 239
- Adsl atuc chanlntvl commands 241
- Example get adsl atuc chanintvl ifname dsli 0 nintrvl 1 241
- Get adsl atuc chanintvl description use this command to get 241
- Output fields 241
- Output ifname dsli 0 intervalnumber 1 rx blocks 10 tx blocks 45 corrected blocks 20 uncorrected blocks 1 gs time elapsed sec 30 valid data true gsnocelldelineation 20 gsheadererrorcheck 0 gsoutofcelldelineation 0 atucchanintvlncds 20 atucchanintvllcds 20 241
- Parameters 241
- Adsl atuc interval commands 242
- Example get adsl atuc interval ifname dsl 0 sintrvl 1 nintrvl 1 242
- Get adsl atuc interval description this command is used to get 242
- Parameters 242
- Output fields 243
- Output ifname dsl 0 intervalnumber 12 intervalvaliddata false intervallofs sec 83 intervalloss sec 84 intervallols sec 85 intervallprs sec 86 intervaless sec 87 intervalinits 88 intervalfastr 191 intervalfailedfastr 192 intervalsesl sec 193 intervaluasl sec 194 intervalfecsl sec 15 gstimeelapsed sec 1001 intervalinitsfailed 15 243
- Output fields 245
- Adsl atuc trap commands 254
- Example example get adsl atuc traps ifname dsl 0 254
- Get adsl atuc traps description this command is used to get 254
- Output fields 254
- Output ifname dsl 0 lofs thresh trap 0 loss thresh trap 1 lols thresh trap 0 lprs thresh trap 1 ess thresh trap 1 init failure trap 1 rate change trap 0 gs opstate trap 1 pm state trap 2 command failure trap 2 254
- Adsl atuc trapsext commands 255
- Example get adsl atuc trapsext ifname dsl 0 255
- Get adsl atuc trapsext description use this command to get 255
- Output fields 255
- Output ifname dsl 0 failed fastr thresh 15min trap 1 sesl thresh 15min trap 1 uasl thresh 15min trap 1 fecsl thresh 15min trap 0 lofs thresh 1day trap 0 loss thresh 1day trap 1 lols thresh 1day trap 1 lprs thresh 1day trap 1 ess thresh 1day trap 0 sesl thresh 1day trap 0 uasl thresh 1day trap 1 fecsl thresh 1day trap 0 255
- Parameters 255
- Adsl atur chanlntrvl commands 256
- Example get adsl atur chanintrvl ifname dsli 0 nintrvl 2 256
- Get adsl atuc chanintrvl description use this command to get 256
- Output ifname dsli 0 intervalnumber 2 rx blocks 10 tx blocks 10 corrected blocks 10 uncorrected blocks 10 gsnocelldelineation 10 gsheadererrorcheck 10 valid data true aturchanintvlncds 20 aturchanintvllcds 20 256
- Parameters 256
- Get adsl atur channel description use this command to get 257
- Output fields 257
- Parameters 257
- References atur interval related commands 5 2 adsl atur channel commands 257
- Example get adsl atur channel ifname dsli 0 258
- Output fields 258
- Output ifname dslf 0 interleave delay ms 10 curr tx rate bps 10 prev tx rate bps 10 crc block length byte 10 gs curr atm status 1 gssymbolsperrsword 10 gsrsdepth 10 gsredundantbytesperrscode 10 aturchanperfatmcd 10 aturchanperfatmcu 10 aturchangsinpup 10 aturchangsl0up 10 aturchangsm0up 10 aturchangst0up 10 aturchangsb0up 10 258
- References adsl commands 259
- Output fields 261
- References adsl commands 262
- Adsl atur interval commands 263
- Example get adsl atur interval ifname dsl 0 nintrvl 1 263
- Get adsl atur interval description this command is used to get 263
- Output fields 263
- Output ifname dsl 0 intervalnumber 1 intervalvaliddata true intervallofs sec 10 intervalloss sec 10 intervallprs sec 10 intervalless sec 10 263
- Parameters 263
- Adsl atur perfext commands 266
- Example get adsl atur perfext ifname dsl 0 266
- Get adsl atur perfext description use this command to get 266
- Parameters 266
- Output fields 267
- Output ifname dsl 0 aturperfstatlossl 14 perfdata curr15min curr1day prev1day perf stat sesl 10 10 10 10 perf stat uasl 10 10 10 10 perf stat fecsl 11 13 19 21 267
- References atur perfdata related commands 267
- Command syntax get adsl atur traps ifname interface name 272
- Example get adsl atur traps ifname dsl 0 272
- Get adsl atur traps description this command is used to get 272
- Parameters 272
- References adsl commands 5 9 adsl atur traps commands 272
- Output fields 274
- Output ifname dsl 0 sesl thresh 15min trap 1 uasl thresh 15min trap 0 fecsl thresh 15min trap 0 lofs thresh 1day trap 1 loss thresh 1day trap 0 lprs thresh 1day trap 1 ess thresh 1day trap 1 sesl thresh 1day trap 1 uasl thresh 1day trap 0 fecsl thresh 1day trap 0 274
- References adsl commands 274
- Parameters 277
- Example get adsl line intf ifname dsl 0 278
- Output ifname dsl 0 line type nochannel coding type dmt gsutopia l2txaddr 23 gsutopia l2rxaddr 10 gsutopia l2rxaddr2nd 11 gsutopia l2txaddr2nd 11 gs clock type oscillator gs action analoglb trans atuc cap ansit1413 trans atuc actual q9921potsnonoverlapped trans atuc config ansit1413 gsdmttrellis trellison trans atur cap ansit1413 278
- Output fields 279
- Pm conf pmsf idleop line delt conf ldsf inhibit curr output pwr dbm 10 10 ds bin snr update enable bin number snr margin bin 0 16 oper status up admin status enable 279
- Example get adsl line profile ifname dsl 0 293
- Output 294
- Max nom atppsd db 10 125 rate adaptation fixed 296
- Min inp inp0 296
- Output fields 296
- Upstream psd mask 296
- References adsl commands 302
- Delete dsl chip description use this command to get 304
- Parameters 304
- Command syntax delet dsl system parameters 309
- Delete dsl system description use this command to get 309
- Example create dsl system dsltype adsl linecoding dmt adsltxcfg ansit1413 shdsltxmode region1 region2 310
- Output fields 310
- Output verbose mode on entry created dsl type adsl line coding dmt adsl tx config ansit1413 shdsl tx mode region1 region2 verbose mode off entry created 310
- Ehdlc commands 311
- Example create ehdlc intf ifname ehdlc 0 lowif dsl 0 sarstatus enable enable 312
- Output verbose mode on entry created ifname ehdlc 0 lowifname dsl 0 ehdlc sar status enable admin status enable verbose mode off entry created 312
- Parameters 312
- Dot3 stats commands 313
- Ethemet commands 313
- Example get dot3 stats ifname eth 0 313
- Get dot3 stats description use this command to get 313
- Output field 313
- Output ifname eth 0 alignment errors 11 fcs errors 12 single collision frames 13 multiple collision frames 14 deferred tx frames 15 late collisions 16 excess collisions frames 17 mac tx errors frames 18 313
- Parameters 313
- Carrier sense errors 18 too long frames 19 mac rx error frames 20 duplex status fullduplex 314
- Output field 314
- Parameters 319
- Example create ethernet intf ifname eth 0 ip 192 68 mask 255 55 55 speed 100bt profilename sprofile mgmtvlanid 2 priority 2 trfclassprofileid 1 ctlpktinstid 1 ctlpktgroupid 1 323
- References ethernet stats command 327
- Eoa commands 328
- Parameters 329
- Example create eoa intf ifname eoa 0 lowif aal5 0 m2vmacdbid 1 enable fcs false 330
- Output fields 330
- Output verbose mode on entry created ifname eoa 0 lowifname aal5 0 fcs false pkt type all inactivity tmr interval 3 m2vmac database id 1 config status normal oper status down admin status up 330
- References ethernet commands ethernet stats commands 331
- Filtering commands 332
- Example create acl global macentry macaddr 00 30 4f a0 d1 34 deny enable track enable 333
- Output field 333
- Output verbose mode on entry created mac address 00 30 4f a0 d1 34 deny true track enable number of times port changed 2 verbose mode off entry created 333
- Parameters 333
- Example create clfr list genentry ifname eoa 1 value 0xac1901aa valtype u8 335
- Output field 335
- Output verbose mode on entry created if name eoa 1 value 0xac1901aa value type u32 verbose mode off entry created 335
- Delete clfr namedlist genentry description use this command to delete 338
- Example create clfr namedlist genentry listid 2 value 0xac1901aa 338
- Output field 338
- Output verbose mode on entry created listid 2 value 0xac1901aa verbose mode off entry created 338
- Parameter 338
- Example create clfr namedlist info listid 2 valtype u32 340
- Output field 340
- Output verbose mode on entry created listid 2 value type u32 verbose mode off entry created 340
- Delete clfr profile branch description use this command to delete 343
- Example create clfr profile branch pname igmp nodeid 3 brtype truebr 343
- Parameter 343
- Example create clfr profile info pname igmp 346
- Output field 346
- Output verbose mode on entry created profile name igmp root nodeid 0 status enable description profile to match the igmp packet verbose mode off entry created 346
- Example create clfr profile node pname igmp nodeid 1 ntype binary actval eq valuetype u16 value 0xffff offsetval 12 maskval 0xffff 352
- Output field 353
- Output verbose mode on entry created profile name igmp node id 3 exported true node type binary modification mask act action eq value type u16 offset 12 mask 0xffff value 0x800 value end none set base type none shift count none multiplier none description node to match the ip address verbose mode off entry created 353
- Example create clfr tree branch tname t1 pid 2 nodeid 1 brtype truebr childpid 1 356
- Parameter 356
- Output field 357
- Output verbose mode on entry created tree name tree1 profile id 3 node id 2 branch type eq child profile id 4 verbose mode off entry created 357
- Example create clfr tree info tname tree1 359
- Output verbose mode on entry created tree name tree1 status disable description tree1 tree priority high verbose mode off entry created 359
- Parameter 359
- Act drop fwd fwdtoctl cptoctl eq gt lt inrange tercmp setprio matchinlist accdeny setbase count retagprio matchingenlist gotonextrule allow valend valend sbasetype abs add 362
- Modify clfr tree node description use this command to get 362
- Parameter 362
- Valtype u8 u16 u32 u64 atmif aal5vc eoaif ethif dir prio len vlanid sbvarindex l2start l3start nodeprio low 362
- Example get clfr tree node tname tree1 pid 2 nodeid 3 365
- Output tree name tree1 profile id 2 node id 3 exported true node type binary modification mask act offset action eq value type u32 offset 12 mask 0x0000000f value 0x0000000f valueend na set base type na shift count na multiplier na description node to match the ip address 365
- Output field 366
- Example create clfr tree profile tname tree1 pid 4 pname srcip 368
- Isroot true false 368
- Modify clfr tree profile description use this command to modify 368
- Parameter 368
- Example create filter list genentry ifname eoa 1 value 0xac1901aa valtype u32 372
- Output field 372
- Output verbose mode on entry created ifname eoa 1 value 0xac1901aa value type u32 verbose mode off entry created 372
- Example create filter namedlist genentry listid 2 value 0xac1901aa valueto 0xac1901aa 374
- Output field 374
- Output verbose mode on entry created listid 2 value 0xac1901aa valueto 0xac1901aa verbose mode off entry created 374
- Example create filter namedlist info listid 2 listtype discrete valtype u32 376
- Output field 376
- Output verbose mode on entry created listid 2 list type discrete value type u32 verbose mode off entry created 376
- Example create filter namedlist map ifname eoa 1 listid 2 378
- Output field 378
- Output verbose mode on entry created ifname eoa 1 listid 2 verbose mode off entry created 378
- Parameter 380
- Actionval 0x00000000 actionmask 0xffffffff 381
- Example create filter rule actionmap ruleid 1 orderindex 1 action setprio priority 3 381
- Output verbose mode on entry created rule id 1 order index 1 action setprio priority 3 actionvalue 0x00000000 action mask 0xffffffff verbose mode off entry created 381
- Output field 382
- Action drop allow setprio sendtocontrol retagprio copytocontrol clfrdef gotonextrule forwardexit exprdef modifytos setbaclevel pktvlanid retagvlanid pktservicevlanid 384
- Parameters 384
- Example create filter rule entry ruleid 1 action setprio description lacp priority 7 status enable statsstatus disable ruleprio high ruledir in applywhenreq disable pkttype ucast snooplevel interface exprid exprid 1 actionval 0x00000000 actionmask 0xffffffff 386
- Output field 387
- Output verbose mode on entry created rule id 1 rule action setprio set priority 7 admin status enable stats admin status disable rule priority high rule direction in applywhenreq disable pkt type ucast application description lacp snoop level interface expression id exprid 1 action value 0x00000000 action mask 0xffffffff verbose mode off entry created 387
- Filter rule map commands 389
- Get filter rule map description use this command to get 389
- Example create filter rule map ifname eoa 0 stageid 1 ruleid 1 orderid 1 391
- Output field 391
- Output verbose mode on entry created interface eoa 0 stage id 1 rule id 1 order id 1 verbose mode off entry created 391
- Example get filter rule stats ruleid 1 392
- Filter rule stats commands 392
- Get filter rule stats description use this command to get 392
- Output field 392
- Output rule id 1 num hits 4354 392
- Parameter 392
- References generic filter commands 392
- Example create filter seq entry seqid 1 ruleid 1 orderid 1 394
- Output field 394
- Output verbose mode on entry created sequence id 1 rule id 1 order id 1 verbose mode off entry created 394
- References generic filter related commands 394
- Example create filter seq info seqid 1 ifname eoa 0 stageid 1 seqdir 1 396
- Output verbose mode on entry created sequence id 1 verbose mode off entry created 396
- 5 3 7 modify filter subrule clfrtree description use this command to modify 405
- Delete filter subrule clfrtree description use this command to delete 405
- Parameter 405
- Parameter 409
- Example create filter subrule ether ruleid 1 subruleid 2 srcmacaddrfrom 00 01 02 03 04 05 srcmacaddrto 00 01 02 03 04 10 dstmacaddrfrom 00 02 03 04 05 11 dstmacaddrto 00 02 03 04 05 15 ethertypefrom 0x0800 ethertypeto 0x0810 vlanidfrom 2 vlanidto 5 priotagfrom 2 priotagto 5 dsapfrom 0xf0 dsapto 0xff ssapfrom 0xf0 ssapto 0xff srcmacaddrcmp inrange dstmacaddrcmp exrange 413
- Output field 415
- References generic filter commands 417
- Parameter 419
- Example create filter subrule generic ruleid 1 subruleid 2 offsethdr tcp offset 20 mask 0xff valuefrom 0x20 valueto 0x40 gencmp inrange subruleprio high namedlistid transporthdr ethernet 420
- Output field 421
- Output verbose mode on entry created rule id 1 subrule id 2 offset header tcp offset 20 generic header comparison inrange mask 0xff subrule priority high start value 0x20 end value 0x40 transport header ethernet namedlist id verbose mode off entry created 421
- Icmptypecmp eq neq any icmpcodecmp eq neq any subruleprio low high asinrule transporthdr ethernet pppoe 423
- Modify filter subrule icmp description use this command to modify 423
- Parameter 423
- Example create filter subrule icmp ruleid 1 subruleid 2 icmptype 0 icmpcode 0 icmptypecmp neq icmpcodecmp neq subruleprio high 424
- Output verbose mode on entry created rule id 1 subrule id 2 icmp type 0 icmp code 0 icmp type comparison neq icmp code comparison neq subrule priority high transport header ethernet verbose mode off entry created 424
- 5 3 1 create filter subrule igmp description use this command to create 425
- Get filter subrule igmp description use this command to get 425
- Output field 425
- References generic filter commands 5 3 1 filter subrule igmp commands 425
- Example create filter subrule igmp ruleid 1 subruleid 2 igmptype 0 igmpcode 0 groupaddr from 224 groupaddrto 224 0 0 0 igmptypecmp eq igmpcodecmp eq igmpgroupaddrcmp inrange subruleprio high 428
- Output field 428
- Output verbose mode on entry created rule id 1 subrule id 2 igmp type 0 igmp type comparison neq igmp code 0 igmp code comparison neq start group address 224 end group address 224 0 0 0 igmp group address comparison inrange subrule priority high transport header ethernet verbose mode off entry created 428
- Get filter subrule ip description use this command to get 429
- References generic filter commands 5 3 2 filter subrule ip commands 429
- Parameter 431
- Toscmp eq neq lt leq gt geq any inrange exrange 431
- Example create filter subrule ip ruleid 1 subruleid 2 srcipaddrfrom 172 5 25 srcipaddrto 172 5 25 dstipaddrfrom 172 5 25 dstipaddrto 172 5 0 25 prototypefrom 1 prototypeto 6 srcaddrcmp inrange dstaddrcmp inrange prototypecmp inrange ipsrcaddrmask 0xffffffff ipdstaddrmask 0xffffffff subruleprio high transporthdr ethernet tosfrom 0x01 tosto 0x06 tosmask 0xff toscmp inrange 434
- Output verbose mode on entry created rule id 1 subrule id 2 start src ip addr 172 5 25 end src ip addr 172 5 25 start dest ip addr 172 5 25 end dest ip addr 172 5 0 25 start ip prot type 1 end ip prot type 6 start tos value 0x01 end tos value 0x06 src ip addr comp inrange dest ip addr comp inrange ip prot type comp inrange tos comp type inrange ip src addr mask 0xffffffff ip dest addr mask 0xffffffff subrule priority high transport header ethernet tos mask 0xff verbose mode off entry created 434
- Output field 435
- 5 3 3 modify filter subrule ppp description use this command to modify 437
- Parameter 437
- Prototypecmp eq neq lt leq gt geq any inrange exrange subruleprio low high asinrule 437
- Example create filter subrule ppp ruleid 1 subruleid 2 prototypefrom 0x1 prototypeto 0x5 prototypecmp inrange subruleprio high 438
- Output field 438
- Output verbose mode on entry created rule id 1 subrule id 2 start prototype 0x1 end prototype 0x5 protocol comparison inrange subrule priority high verbose mode off entry created 438
- Example create filter subrule tcp ruleid 1 subruleid 2 srcportfrom 21 srcportto 23 dstportfrom 21 dstportto 23 srcportcmp inrange dstportcmp inrange subruleprio high 442
- Output field 442
- Output verbose mode on entry created rule id 1 subrule id 2 start source port 21 end source port 23 start destination port 21 end destination port 23 source port comparison inrange destination port comparison inrange subrule priority high transport header ethernet verbose mode off entry created 442
- Modify filter subrule udp description use this command to modify 444
- Parameters 444
- Srcportcmp eq neq lt leq gt geq any inrange exrange dstportcmp eq neq lt leq gt geq any inrange exrange subruleprio low high asinrule transporthdr ethernet pppoe transporthdr ethernet pppoe 444
- Example create filter subrule udp ruleid 1 subruleid 2 srcportfrom 21 srcportto 23 dstportfrom 21 dstportto 23 srcportcmp inrange dstportcmp inrange subruleprio high 445
- Output field 446
- Output verbose mode on entry created rule id 1 subrule id 2 start source port 21 end source port 23 start destination port 21 end destination port 23 source port comparison inrange destination port comparison inrange subrule priority high transport header ethernet verbose mode off entry created 446
- Igmp commands 447
- Parameters 448
- Example get igmpsnoop cfg info 449
- Output field 450
- Output query interval 12 query response interval 10 startup query interval 10 unsolicrprtinterval 10 anxious timer 125 v1 host timer 130 last member query interval 125 robustness variable 2 igmp snoop status enable version mask v3 report suppression status enable proxy report status enable startup qrycount 2 last member qrycount 100 450
- Get igmpsnoop mvlan config description use this command to get 451
- Igmpsnoop mvlan config commands 451
- Example create igmpsnoop mvlan config grpipaddr 224 srcipaddr 12 3 4 5 vlanid 6 mcastvlanstag 5 mcastvlanctag 5 portlist 5 6 10 454
- Output field 454
- Output output verbose mode on entry created grp ipaddress 224 src ipaddres 12 3 4 5 vlan index 6 mcastvlan stag 5 mcastvlan ctag 5 portlist 5 6 10 verbose mode off entry created 454
- Parameters 456
- Example get igmpsnoop port info portid 6 457
- Output field 457
- Output output port index 6 port igmp snoop status enable leave mode normal igmp packetsprio 2maxgroupallowed 2 querier status enable mcastvlan status enable no mcastvlan match action learn 457
- Caution an entry in this table shall not be applicable for a bridge port created over the pppoe interface 458
- Example get igmpsnoop port stats vlanid 6 mcastaddr 00 30 4f 0a 00 01 portid 6 460
- Output field 460
- Output vlan index 6 mcast group address 00 30 4f 0a 00 01 port index 6 query received 100 report received 200 filter mode include include srclist 10 2 4 6 12 0 5 6 exclude srclist 10 2 4 6 34 4 6 7 460
- Delete igmpsnoop querier info description use this command to delete 462
- Example create igmpsnoop querier info vlanid 6 portid 6 462
- Parameters 462
- Interface commands 464
- In mcast pkts 428 out mcast pkts 0 in bcast pkts 1456 out bcast pkts 0 linkupdntrapenable enable promiscous mode true connector present true counterdisconttime 0 hc in octets 0x000060c18 hc outoctets 0x0000293e1 465
- Output fields 465
- Ip commands 469
- Example create arp rid 1 ip 192 68 61 1 macaddr 00 11 22 33 44 55 470
- Output fields 470
- Output verbose mode on entry created rid 1 ifname type static mac address 00 11 22 33 44 55 ip address 192 68 61 1 verbose mode off entry created 470
- Anywan proxyarpstatus enable disable 5 6 delete ip route description use this command to create a routing table entry 472
- Create up route description use this command to create 472
- Parameters 472
- Example create ip route rid 0 ip 192 68 61 2 mask 255 55 gwyip 172 6 00 ifname eth 0 routetype dir proxyarpstatus disable configstatus auto 474
- Output fields 474
- Output verbose mode on entry created rid 0 destination 192 68 61 2 net mask 255 55 gateway 172 6 00 ifname eth 0 route type dir route orig lcl age 0 proxyarpstatus disable verbose mode off entry created 474
- 5 6 modify ipoa intf description use this command to modify 476
- Configstatus normal config enable disable 476
- Delete ipoa intf description use this command to delete 476
- Enable disable 476
- Parameters 476
- Example create ipoa intf ifname ipoa 0 lowif aal5 0 configstatus normal enable 477
- Output fields 477
- Output verbose mode on entry created ifname ipoa 0 low ifname aal5 0 config status normal oper status up admin status enable verbose mode off entry created 477
- Parameters 479
- Example create ipoe intf ifname ipoe 0 lowif ipoa 0 macaddrprof 1 ethpkttype type2 inactivitytmrintrvl 10 routingstatus disable cfgmode auto enable 480
- Output fields 480
- Output verbose mode on entry created ifname ipoe 0 low if name ipoa 0 mac addr prof 1 eth pkt type type2 inactivity tmr interval 10 routingstatus disable oper status up admin status enable verbose mode off entry created 480
- 5 6 delete rid static description use this command to delete 481
- Create rid static description use this command to create 481
- Parameters 481
- Rid static commands 481
- Example create rid static rid 1 482
- Output fields 482
- Output verbose mode on entry created rid 1 verbose mode off entry created 482
- Macprofile commands 484
- Action drop transformedbcast participate 5 7 delete resvdmac profile param description use this command to delete 487
- Create resvdmac profile param description use this command to create 487
- Parameters 487
- Management traffic commands 489
- Pppoe tunneling commands 495
- Example get pppoe global config 497
- Parameters 497
- Output fields 498
- Output max total sessions 10 padi max num retries 10 padr max num retries 10 padi tx interval 5 padr tx interval 5 wan dn tmr interval 10 inactivity tmr interval 20 disc max num retries 3 498
- References pppoe global config related commands 498
- Get pppoe intf description use this command to get 501
- Num of pado rx 2 num of pado rejected 1 num of pads rx 12 num of pads rejected 0 num of malformed pkts rx 2 501
- Output fields 501
- Pppoe intf commands 501
- References pppoe global stats related commands 501
- Example create pppoe intf ifname pppoe 0 lowif ppp 0 wanbridgeport 1 sessionid 10 acmacaddr 00 30 4f 61 c1 be macaddrprof 1 servicenameprof 2 acnameprof 4 ethpkttype type2 nature dynamic 0x1 enable 504
- Output fields 504
- Output verbose mode on entry created ifname pppoe 0 low if name ppp 0 wan bridge port 1 session id 10 ac mac addr 00 30 4f 61 c1 be mac addr prof 1 service name profile 2 ac name prof 4 eth pkt type type2 nature dynamic oper status up admin status enable verbose mode off entry created 504
- References pppoe session config related commands 505
- Output fields 507
- References pppoe session stats related commands 507
- Parameters 509
- Example create pppr intf ifname pppr 0 lowif aal5 0 maxpdu 1484 ppprackto 10 lowiftoggletimerto 10 nature dynamic configstatus normal 510
- Output verbose mode on entry created ifname pppr 0 low ifname aal5 0 max pdu size 1484 ter ack timeout 10 lowif toggle timeout 10 nature dynamic config status normal operational status up admin status up pppoa packetsprio 2 verbose mode off entry created 510
- Output fields 511
- Ia intermeida agent commands 512
- Example create ia profile entry profileid 1 anitype auto anival 00aabbccddff aciprefixstr conexant noida acifieldlist port vpi vci suboption aci chassisval 1 rackval 1 frameval 1 slotval 3 subslotval 1output 524
- Output field 524
- Output verbose mode on entry created profile id 1 ani type auto ani value 00aabbccddff aci prefix str conexant noida aci field list port vpi vci sub option aci chassis 1 rack 1 frame 1 slot 3 sub slot 1 verbose mode off entry created 524
- 5 0 create pia instance entry description use this command to create 525
- Get pia instance entry description use this command to get 525
- References intermediate agent commands 5 0 pia instance entry commands 525
- Parameters 527
- Act for iwftag from client drop 529
- Agent circuit id ani atm 3 10 100 3î slot 3 port 10 vpi 100 vci 33 529
- Config sub options bitmask aci 529
- Encap type llcmux 529
- Entry created 529
- Example create pia instance entry portid 1 vlan 1 profileid 1 status enable vsatag addalways configsuboptionbitmask aci acival ani atm 3 10 100 3î slot 3 port 10 vpi 100 vci 33 raival conexant noida syncratefields actualdelaydnstrm iwftagfromclientact drop insertiwfsubop enable portno 10 auto output 529
- Insert iwf subop enable 529
- L2 type eth 529
- Output 529
- Piavsaoption addalways 529
- Port id 1 vlan 1 529
- Port no 10 529
- Profile id 1 pia status enable 529
- Remote agent id conexant noida 529
- Syncrateinfofield bitmask actualdelaydnstrm 529
- Vci 33 vpi 100 529
- Verbose mode off 529
- Verbose mode on 529
- Output field 530
- Command syntax get pia global config 532
- Example get pia stats entry portid 1 vlan 1 532
- Get pia global config description use this command to get 532
- Output field 532
- Output port id 1 vlan 1 padi received 10 padi discarded 4354 padr received 4354 padr discarded 4354 532
- References pppoe intermediate agent commands 5 0 pia global config commands 532
- Qos commands 534
- Example create irl profile profilename gold irltype trtcm cir 1000 cbs 400 pir 2000 pbs 12000 conformaction colorgreen exceedaction coloryellow violateaction drop 538
- Output 538
- Output field 538
- References irl commands 538
- Bridge rlin stance map commands 540
- Create bridge rlinstance map 540
- Delete bridge rlinstance map 540
- Get bridge rlinstance map 540
- Modify bridge rlinstance map 540
- Example create bridge rlinstance map portid 6 flowtype bcast instanceid 1 configstatus auto 541
- Output field 541
- Output verbose mode on entry created port id 6 flow type bcast instance id 1 verbose mode off entry created 541
- Modify rl actionprofile info description use this command to modify 543
- Parameters parameters 543
- Result conform exceed violate action drop allow sendtocontrol copytocontrol modifytos setbaclevel 543
- Example create rl actionprofile info profileid 1 result conform action copytocontrol actionval 0x00000000 actionmask 0xffffffff description lacp 544
- Output field 545
- Output verbose mode on entry created action profile id 1 action result conform profile action copytocontrolactionval 0x00000000 action mask 0xffffffff application description lacp verbose mode off entry created 545
- Example create rl instance info instanceid 3 profileid 2 actionprofileid 1 547
- Output verbose mode on entry created instance id 3 profile id 2 action profile id 1 verbose mode off entry created 547
- Parameters parameters 547
- Modify rl profile info description use this command to modify 549
- Parameters parameters 549
- Example create rl profile info profileid 1 rate 24 mbs 24 level packet type trtcm peakrate 30 pbs 30 550
- Output field 551
- Output verbose mode on entry created profile id 1 level packet type trtcm rate 24 max burst size 24 peak rate 30 peak max burst size 30 verbose mode off entry created 551
- Example get sched profile class name gold classid 1 554
- Output field 554
- Output output profile name gold class id 1 profile class param1 20 profile class param2 25 profile class param3 25 profile class param4 0 profile class param5 25 554
- Delete sched profile info description use this command to delete 556
- Example create sched profile info name gold algo pp iftype atm 556
- Output output verbose mode on verbose mode on entry created profile name gold scheduling algorithm pp interface type eth verbose mode off entry created 556
- Parameters parameters 556
- Example get trfclass profile class profileid 1 classid 1 558
- Modify trfclass profile class description use this command to get 558
- Output profile identifier 1 class id 1 traffic class param size 32 traffic class param thresh 50 558
- Parameters parameters 558
- Rmon commands 562
- Example get srmon probe rindex 1 563
- Output field 563
- Output verbose mode on rmon probe index 1 if name eth 0 stats owner conexant total octets 800 total packets 200 total broadcast packets 138 total multicast packets 200 total 64 octets 100 total 65 127 octets 200 total 128 255 octets 200 total 256 511 octets 300 total 512 1023 octets 50 total 1024 1518 octets 100 563
- Caution this command is not supported on an eoa interface for which configstatus is set to config 5 2 rmon task info commands 564
- Get rmon task description use this command to get 564
- Parameters 564
- Example get rmon task taskname tsk1 565
- Output field 565
- Output name tsk1 status event suspend sched count 1 priority 10 preempt yes time slice 0 stack base 0x520cc18 stack size 2048 cleanstacksize 14080 lastschedtime thu jan 01 00 00 08 1970 565
- Output field 567
- Example 2 for fixed size memory pool get rmon mpool ftsk142 568
- Output name ftsk142 size 280 partion size 20 allocated 1 free 9 tasks waiting 0 suspend type fifo startaddr 0x5307e40 firsttaskname firstallocator tsk1 lastallocator tsk1 lastdellocater tsk1 lastfailuser lastfaildellocater watermark 84 totalmemalloc 3 totalmemfree 2 memallocfailcount 0 memfreefailcount 0 mpooltype parttion threshold 280 threhold count 0 lastmemalloctime thu jan 01 00 02 34 1970 lastmemfreetime thu jan 01 00 02 49 1970 568
- Lastmemallocfailtime lastmemfreefailtime thresholdhittime 569
- Output field 569
- Get rmon mpool threshold description use this command to get the critical events logged for the memory pool this command will display 20 entries maximum events are logged for the memory pool for the following 3 cases mem pool allocation fail mem pool deallocation fail threshold hit 570
- Command syntax get rmon mpool threshold 571
- Example get rmon mpool threshold 571
- Output field 571
- Output task name tsk1 mpool name ftsk143 pool type partition thresholdhittimestamp thu jan 01 00 20 53 1970 event type allocation fail 571
- Parameters none 571
- Example get rmon queue rname tsk173 573
- Output field 573
- Output name tsk173 start addr 0x520c700 size 10 available size 9 pending msgs 1 msg type fixed msg size 1 suspend type priority tasks waiting 0 firsttaskname totalmsgin 3 totalmsgout 2 dropcount 0 watermark 3 lastmsginfailptr 0x0 lastsender tsk2 lastrecvr tsk1 lastsenderfail lastrecvfail threshhold 10 thresholdhitcount 0 lastmsgouttime thu jan 01 00 04 17 1970 lastmsgintime thu jan 01 00 03 50 1970 lastmsgoutfailtime lastmsginfailtime thresholdhittime 573
- Output field 577
- Output totalnetbuf 116 totalused 8 totalfree 7 watermark 3 threshold 116 thresholdhitcount 0 allocfailcount 0 freefailcount 0 lastusertask pkev lastfreetask pkev lastuserfailtask lastfreefailtask thresholdhittask lastusedtime thu jan 01 00 04 45 1970 lastfreetime thu jan 01 00 05 01 1970 lastusefailtime thresholdhittime 577
- Snmp commands 582
- Example get snmp stats 586
- Output field 586
- Output inpkts 100 outpkts 100 inbadversions 0 inbadcommunitynames 0 inbadcommunityuses 0 inasnparseerrs 0 intoobigs 0 innosuchnames 0 inbadvalues 0 inreadonlys 0 ingenerrs 0 intotalreqvars 200 intotalsetvars 0 ingetrequests 100 ingetnexts 0 insetrequests 0 ingetresponses 0 intraps 0 outtoobigs 0 outnosuchnames 0 outbadvalues 0 outgenerrs 0 outgetrequests 0 outgetnexts 0 outsetrequests 0 outgetresponses 100 outtraps 0 authentraps disable silentdrops 0 proxydrops 0 586
- 5 3 modify snmp traphost description use this command to modify 589
- Delete snmp traphost description use this command to delete 589
- Parameter 589
- Version v1 v2c severity critical major minor info 589
- Sntp commands 591
- System commands 594
- Parameters 596
- Example create user name user1 passwd temp1 user 598
- Output fields 598
- Output verbose mode on entry created privilege username user user1 verbose mode off entry created 598
- Parameters 598
- References delete user command get user command passwd related commands 598
- Example get system crash info numentries 1 showview general ctrlandstatusregs stackregs stackinfo altwinregs stdwinregs coprocessorregs 601
- Mode super user user 601
- Output 601
- Output fields 605
- Note the current standard window dump displays the current dump corresponding to global out local and in 607
- Command syntax get system info 5 5 modify system info description use this command to modify the system parameters 609
- Get system info description this command to get system parameters 609
- Parameters parameters 609
- System info commands 609
- Example get system info 611
- Output verbose mode on description columbia name conexant com location conexant systems inc 100 schulz drive redbank nj 07701 u s a contact conexant systems inc 100 schulz drive redbank nj 07701 u s a vendor conexant systems inc 100 schulz drive redbank nj 07701 u s a logthreshold 0 object id 1 00 up time hh mm ss 5 2 0 hwversion c023b6d3 611
- Cpswversion col2 40707 dpswversion system time thu jan 01 05 02 00 1970 time zone gmt dst off services physical datalink internet end to end applications 612
- Output fields 612
- References get modify nbsize get system stats 612
- Example get rmon idletime numentries 1 613
- Get rmon idletime description use this command to display a list of idle time records 613
- Mode super user user 613
- Output fields 613
- Output get rmon idletime numentries 1 start time end time total idle util time time thu jan 1 12 34 51 1970 thu jan 1 12 35 00 1970 10s 7s 30 613
- Parameters 613
- Output fields output fields 615
- X84a00000 0 2 0x84a00c00 1 logical to physical port mapping 0 7 0 1 2 3 4 5 6 7 8 15 8 9 10 11 12 13 14 15 16 23 16 17 18 19 20 21 22 23 24 31 24 25 26 27 28 29 30 31 32 39 32 33 34 35 36 37 38 39 40 47 40 41 42 43 44 45 46 47 uart manuf text info num of uarts 1 hssl port id 1 baud rate 9600 data bits 8 stop bit 2 parity even uart mode polling application type console 615
- Command syntax get system reboot info numentries 616
- Get system reboot info description this command is used for displaying a list of reboot failures that were encountered when the system was trying to come up 616
- System reboot info commands 616
- Example get system reboot info numentries 1 617
- Output fields 617
- Output output verbose mode on cp bin version 1 dp bin version 1 time of reboot thu jan 2 12 34 56 1970 reboot failure cause dp init failure reboot type secondary cfg 617
- Parameters 617
- Abondglbsidfmt eightbitsid twelvebitsid 619
- Parameters 619
- Example get nbsize 623
- Output fields output fields 624
- Output max atm ports 48 max vc per port 8 max vcs 384 max oam activities 10 max rmon probes 20 bridging mode residential max multicast groups 256 max mac addresses 4000 max hash buckets 8192 max vlans 512 max vlanid value 4095 max num static mac entries 512 dev capabilities ivl max num eoa prio qs 3 max num eth prio qs 8 max high prio tree nodes 100 max low prio tree nodes 200 max clfr trees 63 max clfr profiles 63 max in rules 250 max out rules 50 max in highprio subrules 100 max in lowprio subrules 300 max out highprio subrules 50 max out lowprio subrules 150 mcast capabilities ivmcapable max access concentrators 2 max src mac addresses 4 vlan mode 1 s vlan protocol id 0x9100 t vlan protocol id 0x9200 t vlan id 1 abondglbctrlvpi 0 abondglbctrlvci 20 abondglbsidfmt twelvebitsid ridcap srdcapable 624
- Dnlink learn entry discards 30 net learn entry discards 100 dyn addr conflicts static 40 moved dyn addrs count 110 ucast lookup fail count 50 mcast lookup fail count 120 tx ctl pkts count 60 rx ctl pkts count 130 ctl pkts discards count 70 pppoe session look up failures 5 628
- Output fields 628
- References get modify system info get modify nbsize 628
- Example get traps 630
- Mode super user user 630
- Output fields 630
- Output thu jan 01 00 00 13 1970 status alarm atm vc up interface name aal5 0 thu jan 01 00 00 13 1970 status alarm system up 630
- Parameters 630
- Example modify trace cfg module gag flow 0x1 level 0x1 639
- Gag 0x0 0x0 stdout 0 0 639
- Gag 0x1 0x1 stdout 0 0 639
- Mode super user 639
- Module flow level type destn port 639
- Output 639
- Set done 639
- Verbose mode on 639
- Command syntax get trace stats 640
- Get trace stats command 5 5 4 trace log statistics commands 640
- Get trace stats description use this command to display trace statistics 640
- Output fields 640
- Parameters none 640
- References get trace cfg command 640
- Set done 640
- Verbose mode off 640
- Vc aggregation commands 642
- Example create atm vcaggr intf ifname vcaggr 0 mapid 1 defaultdnstrmvc aal5 0 enable 643
- Output verbose mode on entry created ifname vcaggr 0 vc mapid 1 default downstream vc aal5 0 643
- Parameters 643
- Atm vcaggr map commands 644
- Get atm vcaggr map description use this command to get 644
- Oper status up admin status down verbose mode off entry created 644
- Output fields 644
- Example create atm vcaggr map mapid 1 vc aal5 0 dnstrmpriolist 1 3 7 upstrmdefprio 2 upstrmregenprio 2 647
- Output fields 647
- Output verbose mode on entry created vc map id 1 vc intf aal5 0 up stream default priority 2 up stream regen priority 2 downstream priority map 1 3 7 verbose mode off entry created 647
- Vlan commands 648
- Example get gvrp port info portid 10 651
- Output fields 652
- Output verbose mode on vlan version number 1 current vlans 1000 gvrp status enable set done vlan version number 1 current vlans 1000 gvrp status enable verbose mode off set done 652
- References gvrp commands 653
- Get vlan curr info description use this command to get 655
- Parameters parameters 655
- References gvrp commands 5 7 vlan curr info commands 655
- Example get vlan curr info vlanid 45 656
- Output field output field 656
- Output vlan index 45 vlan status 1 egress ports 24 untagged ports 24 bridging mode residential flood support status enable broadcast support status enable reserved mac profile id 1 656
- Get vlan mapprofile info description use this command to get 657
- Vlan mapprofile info commands 657
- Field description 668
- Output field 668
- Apply description use this command to apply a configuration file stored on the system 672
- Besteffort true false 672
- File commands 672
- Miscelleneous commands 672
- Mode super user 672
- Parameters 672
- Download description use this command to download a binary configuration or user specific file from the remote host 674
- Mode tftp ftp savemode comapact 674
- Parameters 674
- Example download src myconfig cfg dest nvram user myconfig cfg ip 198 68 675
- Output fields output fields none 675
- Output verbose mode on downloading the code file download completed verbose mode off downloading the code file download completed 675
- Output 677
- Name logs 680
- Name user txt 680
- Nvram user 680
- Output fields 680
- Permission rw state active 680
- Permission sys state active 680
- References upgrade command remove command apply command download command 680
- Time thu dec 23 15 42 26 2004 680
- Used blocks 1 680
- Used blocks 2 680
- Version 1 size bytes 130988 680
- Version 1 size bytes 5768 680
- Parameters 682
- References upgrade command remove command list command download command 5 8 ping description use to send one or more icmp messages to another host for a reply 682
- Example ping 192 68 3 683
- Output fields 683
- Output ping 192 68 3 64 bytes of data from 192 68 3 seq 0 ttl 64 rtt 0 00 msec 64 bytes of data from 192 68 3 seq 1 ttl 64 rtt 0 00 msec 64 bytes of data from 192 68 3 seq 2 ttl 64 rtt 0 00 msec 64 bytes of data from 192 68 3 seq 3 ttl 64 rtt 0 00 msec ping statistics 4 packets transmitted 4 packets received 0 percent packet loss 683
- Parameters parameters 683
- Remove description use this command to remove a configuration or binary file stored on the unit 683
- Caution caution ensure that the tftp server is running on the remote host 686
- Example upload src nvram system primcfg dest myconfig cfg ip 198 68 686
- Output fields output fields none 686
- Output output verbose mode on uploading the code file upload completed verbose mode off uploading the code file upload completed 686
- Parameters 686
- References references commit command 686
- Caution none the modified prompt is not saved across a reboot 5 8 traceroute description this command is used to trace the route to the specified destination 691
- Example traceroute 192 68 3 ping 691
- Parameters parameters 691
- Command syntax verbose on off 692
- Mode super user 692
- Output fields output fields 692
- Output tracing route to 192 68 3 over a maximum of 30 hops 1 0 00000 ms 0 00000 ms 0 00000 ms 192 68 3 trace complete 692
- Parameters parameters 692
- References ping command 5 8 verbose description using this command a user can view the status of entries before and after the execution of a command create delete modify get however if this mode is turned off then display only shows the final result of execution of command i e whether it was successful or failure 692
- Appendix a fd cfg in detail 693
- Appendix b supported mibs 698
- Propmib conexant 698
- Stdmib standard 699
- Appendix c ieee 802 x protocol over ip dslam 700
- Understanding how 802 x authentication works understanding how 802 x authentication works 700
- Device roles with 802 x port based authentication the devices in the network have specific roles see below figure 701
- Configuring 802 x authentication the following sections describe how to configure 802 x authentication on the switch 703
- Specifying radius servers to specify one or more radius servers perform this task in privileged mode 703
- Specifying the radius key use the radius key to encrypt and authenticate all communication between the radius client and server you must configure the same key on the client and the radius server the length of the key is limited to 65 characters it can include any printable ascii characters except tabs to specify the radius key perform this task in privileged mode 703
- X cli commands 703
- Appendix d what s ip dslam 706
Похожие устройства
- Zoje ZJ-1414-100-403-601-603-04095 Инструкция по эксплуатации
- Krona Bella 600 Black pb Инструкция по эксплуатации
- Planet IDL-4802 Инструкция по эксплуатации
- Zanussi ZOB5282WC Инструкция по эксплуатации
- De Dietrich CF 120 CSE Инструкция по эксплуатации
- Planet IDL-4802-48 Инструкция по эксплуатации
- Zanussi ZOB5282CC Инструкция по эксплуатации
- Thermex COMBI Инструкция по эксплуатации
- Planet VC-301 Инструкция по эксплуатации
- Hotpoint-Ariston 7OFK1039EL X RU/HA Инструкция по эксплуатации
- Thermex EQ Инструкция по эксплуатации
- Planet VC-230 Инструкция по эксплуатации
- Zanussi ZGG566414M Инструкция по эксплуатации
- Thermex ER 200 300 ЛИТРОВ Инструкция по эксплуатации
- Planet VC-230N Инструкция по эксплуатации
- Planet VC-2402 Инструкция по эксплуатации
- Thermex ES Инструкция по эксплуатации
- Planet VC-2402-48 Инструкция по эксплуатации
- Thermex IR Инструкция по эксплуатации
- Planet VC-810S Инструкция по эксплуатации