Vitek VT-1190 [4/32] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-1190 [4/32] English

Vitek VT-1190 [4/32] English
4
ENGLISH
• Before taking the unit away for long storage or
before cleaning, unplug it, pour out water and
let the unit cool down and dry.
• For children’s safety reasons do not leave
polyethylene bags used as packaging unat-
tended.
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger of
suffocation!
• Close supervision is necessary when chil-
dren or disabled persons are near the oper-
ating unit.
• The unit is not intended for usage by physi-
cally or mentally disabled persons (including
children) or by persons lacking experience or
knowledge if they are not under supervision of
a person who is responsible for their safety or
if they are not instructed by this person on the
usage of the unit.
• Do not leave children unattended to prevent
them from using the unit as a toy.
• Never use the unit if the power cord or the
power cord plug is damaged, if the unit works
improperly or after it was dropped.
• If the power cord is damaged, it should be
replaced with a special cord or a set received
from the manufacture or service.
• Do not repair the unit by yourself. Do not dis-
assemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and apply to any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.vitek.ru.
• Transport the unit in the original packaging
only.
• Keep the unit out of reach of children and
people with disabilities.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After the unit transportation or storage at
low temperature keep it for at least three
hours at room temperature before switch-
ing on.
There may be water spots in the thermopot,
this is normal, as the unit has undergone
factory quality control.
• Unpack the thermopot; remove any advertis-
ing stickers that can prevent the unit opera-
tion.
• Check the unit for damages, do not use it in
case of damages.
• Make sure that the unit operating voltage cor-
responds to the voltage of your mains.
• Place the thermopot on a dry flat surface
keeping at least 20 cm gap between the ther-
mopot body and the wall or furniture and at
least 50 cm gap above the thermopot.
• Open the lid (8) by pressing the button (6) and
holding it (pic. 1).
• Fill the thermopot with water using a suitable
bowl, do not exceed the maximal water level
mark (15) «FULL».
• Insert the power cord connector (16) into the
socket (12) on the thermopot body and the
power cord (16) plug into the mains socket.
You will hear a sound signal, and all indica-
tors on the control panel (5) will light up for
2 seconds. After that the thermopot will be
switched on in the boiling mode, the indica-
tor (17) “BOILING” will glow constantly and the
indicator (18) “85°” will be flashing. The keep
warm temperature «85°С» is set by default.
• After long water boiling you will hear sound
signals and the thermopot will switch to
the keep warm mode, the indicator (17)
“BOILING” will go out and the keep warm
mode indicator (18) «85°» will be flashing.
Notes:
– the thermopot uses a long boiling technology
which allows to significantly reduce the chlo-
rine level in water.
– every pressing of the control buttons is
accompanied with a sound signal.
– after pressing the control buttons the water
level scale illumination lights up and goes out
after 15 seconds.
• Drain the water; to do this, you must unlock
the activation of the water pump by pressing
the button (21) «UN/LOCK», the indicator (20)
“
” will light up.
Attention! Be careful when pouring out water to
avoid burns by hot water.
Version 1:
– place a suitable bowl, for instance, a cup
under the spout for pouring water (4) and
press the water dispense button (3) with a rim
of the cup (pic. 2).
IM VT-1190.indd 4 11.04.2019 15:03:05

Содержание

Похожие устройства

Скачать