Vitek VT-1190 [6/32] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-1190 [6/32] English

Vitek VT-1190 [6/32] English
6
ENGLISH
• To switch the thermopot off press the
water temperature selection button (23)
“TEMP.SET/KEEP WARM” and select the
“ROOM TEMP” mode, the indicator (19)
“ROOM TEMP” will light up.
Note: - after 48 hours the thermopot will
switch to the standby mode, the indicator (17)
“BOILING” will be flashing a little bit. To switch off
the standby mode press any button on the con-
trol panel (5).
• To switch the thermopot off disconnect the
power plug (16) from the mains socket.
• Open the thermopot lid (8) and wait until it
cools down completely, remove the lid (8)
(see the chapter BEFORE THE FIRST USE),
drain the water, install the lid (8) back to its
place and put the thermopot away for storage.
Overheating protection
• If you accidentally switched the thermopot
on and the water level is below the minimal
mark “MIN”, the automatic thermal switch
will be on, you will be hearing sound sig-
nals for 20 seconds and all indicators on the
control panel (5) will be flashing. In this case
unplug the thermopot and let it cool down
for 10-20 minutes, then fill it with water, and
switch the thermopot on, the unit will operate
in normal mode.
CLEANING AND CARE
• Before cleaning, disconnect the thermopot
from the mains, pour out water and let the
thermopot cool down completely.
• Before removing the lid (8) open it and pull the
lid (8) to the control panel (5) (pic. 3).
• Carefully tilt the thermopot to drain the
remaining water.
• Install the lid (8) back to its place. To do it,
place the lid (8) at a small angle and install the
lid (8) to its installation place. Before using
the thermopot make sure that the lid (8) is
fixed properly.
• Clean the outer surface of the thermopot with
a slightly damp cloth and then wipe it dry.
• Use neutral detergents to remove dirt; do not
use metal brushes, abrasive detergents and
solvents.
• Do not immerse the thermopot and the power
cord into water and other liquids.
• Do not wash the thermopot in a dishwashing
machine.
Stains on the inner surface
of the thermopot
The inner surface of the metal flask may change
its color under the influence of different water
impurities.
• You can remove the stains with citric acid or
vinegar.
• To remove the flavour of citric acid or vinegar,
boil water and pour it out.
• Repeat this procedure until the smell and
taste vanish completely.
Descaling
• Scale, appearing inside the metal flask,
causes the heating element overheating and
malfunction. Burning of the heating element
caused by the scale in the thermopot is not
covered by warranty.
• To remove the scale fill the thermopot with a
mixture of one part ordinary vinegar and two
parts water up to the maximal level mark (15)
«FULL».
• Insert the power cord (16) connector into the
socket (12) on the thermopot body, and the
power cord (16) plug into the mains socket.
• The thermopot will be switched on in the boil-
ing mode. After the water boiling disconnect
the power cord (16) plug from the socket and
leave the thermopot filled with the vinegar
solution overnight.
• In the morning pour out the vinegar solu-
tion, fill the thermopot with water up to the
maximal level «FULL», boil it and pour out
the water.
• You can use special detergents for electric
kettles to remove scale, strictly following the
instructions on the detergent usage.
• If necessary, perform the cleaning procedure
several times.
STORAGE
• Before taking the thermopot away for long
storage, unplug it, let the unit cool down and
pour out the remaining water.
• Clean the thermopot.
• Keep the thermopot out of reach of children
and disabled persons.
DELIVERY SET
Thermopot – 1 pc.
Power cord – 1 pc.
Instruction manual – 1 pc.
IM VT-1190.indd 6 11.04.2019 15:03:05

Содержание

Похожие устройства

Скачать