Vitek VT-1190 [5/32] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-1190 [5/32] English

Vitek VT-1190 [5/32] English
5
E N G L I S H
Version 2:
– place a suitable bowl under the spout for
pouring water (4) and press the water dis-
pense button (22) «DISPENSE».
Note: - the water is dispensed only when the
indicator (20) “
” is switched on; if you pressed
the button (21) “UN/LOCK” and didn’t do any-
thing, the indicator (20) will go out in 10 sec-
onds.
• To switch the thermopot off press the water
temperature selection button (23) “TEMP.SET/
KEEP WARM” and select the “ROOM TEMP”
mode, the indicator (19) “ROOM TEMP” will
light up.
• To switch the thermopot off disconnect the
power plug (16) from the mains socket.
• Open the thermopot lid (8) and wait until it
cools down completely.
• Before removing the lid (8) open it and pull the
lid (8) to the control panel (5) (pic. 3).
• Carefully tilt the thermopot to drain the
remaining water.
• Install the lid (8) back to its place. To do it,
place the lid (8) at a small angle and install the
lid (8) to its installation place. Before using
the thermopot make sure that the lid (8) is
fixed properly.
• The thermopot is ready for operation.
USAGE OF THERMOPOT
• Open the lid (8) by pressing the button (6) and
holding it (pic. 1).
• Fill the thermopot with water using a suitable
bowl, do not exceed the maximal water level
mark (15) «FULL».
• Insert the power cord connector (16) into the
socket (12) on the thermopot body and the
power cord (16) plug into the mains socket.
You will hear a sound signal, and all indica-
tors on the control panel (5) will light up for
2 seconds. After that the thermopot will be
switched on in the boiling mode, the indica-
tor (17) “BOILING” will glow constantly and the
indicator (18) “85°” will be flashing.
• The keep warm temperature «85°» is set by
default.
• After long water boiling you will hear sound
signals and the thermopot will switch to
the keep warm mode, the indicator (17)
“BOILING” will go out and the keep warm
mode indicator (18) «85°» will be flashing.
• When the water in the thermopot cools down
to 85°, the indicator (18) will glow constantly
and the water temperature will be maintained.
• If the water temperature goes significantly
below the preset temperature, for instance,
if you added some cold water, the boiling
mode will be switched on, the indicator (17)
“BOILING” will light up. After boiling the water
temperature will be maintained depending on
the preset value and will be shown with the
indicators (18).
• To change the required keep warm temper-
ature press the temperature selection but-
ton (23) «TEMP.SET/KEEP WARM». You can
select the keep warm temperature «45°С-55°С-
65°С-85°С-95°С».
• Recommended temperature for brewing tea
and making other beverages:
– «45°» – water temperature for powdered
baby milk
– «85°» – green and yellow tea
– «95°» – black tea
• The preset temperature is shown by the cor-
responding indicators (18).
Note: - to reboil the water press the button (24)
“REBOIL”. The indicator (17) “BOILING” will light
up. To switch the reboiling mode off press the
button (24) “REBOIL” again, the indicator (17)
“BOILING” will go out and the thermopot will
switch back to the keep warm mode.
• Drain the water; to do this, you must unlock
the activation of the water pump by pressing
the button (21) «UN/LOCK», the indicator (20)
“
” will light up.
Attention! Be careful when pouring out water to
avoid burns by hot water.
Version 1:
– place a suitable bowl, for instance, a cup
under the spout for pouring water (4) and
press the water dispense button (3) with a rim
of the cup.
Version 2:
– place a suitable bowl under the spout for
pouring water (4) and press the water dis-
pense button (22) «DISPENSE».
Note: - the water is dispensed only when the
indicator (20) “
” is switched on; if you pressed
the button (21) “UN/LOCK” and didn’t do any-
thing, the indicator (20) will go out in 10 seconds.
IM VT-1190.indd 5 11.04.2019 15:03:05

Содержание

Похожие устройства

Скачать