![Makita GA6021C (155139) [8/72] Functional description functional description](/img/pdf.png)
Makita GA6021C (155139) [8/72] Functional description functional description
![Makita ga6021c [8/72] Functional description functional description](/views2/1175406/page8/bg8.png)
8
e) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under
their own weight. Supports must be placed under
the workpiece near the line of cut and near the
edge of the workpiece on both sides of the wheel.
f) Use extra caution when making a “pocket
cut” into existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding
disc paper. Follow manufacturers
recommendations, when selecting sanding
paper. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may
cause snagging, tearing of the disc or kickback.
Safety Warnings Specific for Wire Brushing
Operations:
a) Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive
load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire
brushing, do not allow interference of the wire
wheel or brush with the guard. Wire wheel or
brush may expand in diameter due to work load
and centrifugal forces.
Additional safety warnings:
17. When using depressed centre grinding wheels,
be sure to use only fiberglass-reinforced
wheels.
18. Be careful not to damage the spindle, the
flange (especially the installing surface) or the
lock nut. Damage to these parts could result in
wheel breakage.
19. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
20. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced wheel.
21. Use the specified surface of the wheel to
perform the grinding.
22. Watch out for flying sparks. Hold the tool so
that sparks fly away from you and other
persons or flammable materials.
23. Do not leave the tool running. Operate the tool
only when hand-held.
24. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
25. Always be sure that the tool is switched off
and unplugged or that the battery cartridge is
removed before carrying out any work on the
tool.
26. Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
27. Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.
28. Use only flanges specified for this tool.
29. For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the wheel
is long enough to accept the spindle length.
30. Check that the workpiece is properly
supported.
31. Watch out for flying sparks. Hold the tool so
that sparks fly away from you and other
persons or flammable materials.
32. Pay attention that the wheel continues to
rotate after the tool is switched off.
33. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure
operator safety.
34. Do not use the tool on any materials
containing asbestos.
35. Do not use water or grinding lubricant.
36. Ensure that ventilation openings are kept clear
when working in dusty conditions. If it should
become necessary to clear dust, first
disconnect the tool from the mains supply
( use non metallic objects ) and avoid
damaging internal parts.
37. When use cut-off wheel, always work with the
dust collecting wheel guard required by
domestic regulation.
38. Cutting discs must not be subjected to any
lateral pressure.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
SAVE THESE INSTRUCTIONS.
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
Shaft lock
Fig.1
CAUTION:
• Never actuate the shaft lock when the spindle is
moving. The tool may be damaged.
Press the shaft lock to prevent spindle rotation when
installing or removing accessories.
Содержание
- Ga5020 ga5020c ga5021 ga5021c ga6020 ga6020c ga6021 ga6021c 1
- Explanation of general view 4
- Specifications 4
- Ec declaration of conformity 6
- Specific safety rules 6
- Functional description functional description 8
- Save these instructions 8
- Shaft lock 8
- Warning 8
- Assembly 9
- Electronic function constant speed control for models ga5020c ga5021c ga6020c ga6021c 9
- Installing loop handle accessory 9
- Installing side grip handle 9
- Soft start feature 9
- Switch action 9
- Grinding and sanding operation 10
- Installing or removing depressed center grinding wheel multi disc accessory 10
- Installing or removing wheel guard 10
- Operation 10
- Operation with abrasive cut off wheel accessory 10
- Accessories 11
- Maintenance 11
- Replacing carbon brushes 11
- Förklaring till översiktsbilderna 12
- Specifikationer 12
- Eg deklaration om överensstämmelse 14
- Specifika säkerhetsanvisningar 14
- Avtryckarens funktion 16
- Funktionsbeskrivning funktionsbeskrivning 16
- Spara dessa anvisningar 16
- Spindellås 16
- Varning 16
- Elektronisk funktion varvtalsstyrning modell ga5020c ga5021c ga6020c ga6021c 17
- Mjukstartfunktion 17
- Montera sidohandtaget 17
- Montering 17
- Montering av handtagsögla tillbehör 17
- Användning 18
- Användning med slipande kapskiva tillbehör 18
- Montera eller demontera rondell med försänkt centrumhål multirondell tillbehör 18
- Montera eller demontera sprängskyddet 18
- Slipning av trä och metall 18
- Underhåll 18
- Byte av kolborstar 19
- Tillbehör 19
- Oversiktsforklaring 20
- Tekniske data 20
- Eus samsvars erklæring 22
- Spesifikke sikkerhetsregler 22
- Advarsel 24
- Funksjonsbeskrivelse funksjonsbeskrivelse 24
- Spindellås 24
- Ta vare på disse instruksene 24
- Bryterfunksjon 25
- Elektronisk funksjon kontroll for konstant hastighet for modell ga5020c ga5021c ga6020c ga6021c 25
- Montere bøylehåndtak tilbehør 25
- Montere støttehåndtak hjelpehåndtak 25
- Montering 25
- Mykstartfunksjon 25
- Bruke kappeskive tilbehør 26
- Installere eller fjerne nedtrykket sentrert slipeskive multidisk tilleggsutstyr 26
- Montere eller fjerne beskyttelseskappen 26
- Sliping og pussing 26
- Skifte kullbørster 27
- Tilbehør 27
- Vedlikehold 27
- Tekniset tiedot 28
- Yleisen näkymän selitys 28
- Erityiset turvasäännöt 30
- Vakuutus ec vastaavuudesta 30
- Lukitus 32
- Säilytä nämä ohjeet 32
- Toimintakuvaus toimintakuvaus 32
- Varoitus 32
- Kokoonpano 33
- Kytkimen toiminta 33
- Pehmeä käynnistys 33
- Silmukkakahvan asennus lisävaruste 33
- Sivukahvan asentaminen kahva 33
- Sähköinen toiminta jatkuva nopeudensäädin mallille ga5020c ga5021c ga6020c ga6021c 33
- Hionta 34
- Hiovalla katkolaikalla toiminta lisävaruste 34
- Keskeltä ohennetun laikan monilaikan lisävaruste kiinnittäminen ja irrottaminen 34
- Käyttö 34
- Laikan suojuksen asentaminen tai irrottaminen 34
- Hiiliharjojen vaihtaminen 35
- Huolto 35
- Lisävarusteet 35
- Kopskata skaidrojums 36
- Specifikācijas 36
- Ek atbilstības deklarācija 38
- Papildus drošības noteikumi 38
- Brīdinājums 41
- Elektroniskā vadība pastāvīga ātruma regulēšana modelim ga5020c ga5021c ga6020c ga6021c 41
- Funkciju apraksts funkciju apraksts 41
- Maigās palaišanas funkcija 41
- Saglabājiet šos norādījumus 41
- Slēdža darbība 41
- Vārpstas bloķētājs 41
- Cilpas roktura uzstādīšana piederums 42
- Ekspluatācija 42
- Montāža 42
- Slīpripas aizsarga uzstādīšana un noņemšana 42
- Slīpripas ar ieliektu centru multi disc piederums uzstādīšana un noņemšana 42
- Sānu roktura uzstādīšana rokturis 42
- Abrazīvās griezējripas lietošana piederums 43
- Apkope 43
- Ogles suku nomaiņa 43
- Piederumi 43
- Slīpēšana un nolīdzināšana 43
- Bendrasis aprašymas 44
- Specifikacijos 44
- Es atitikimo deklaracija 46
- Konkrečios saugos taisyklės 46
- Saugokite šias instrukcijas 48
- Veikimo aprašymas veikimo aprašymas 48
- Įspėjimas 48
- Ašies fiksatorius 49
- Elektroninė funkcija pastovaus greičio kontrolė ga5020c ga5021c ga6020c ga6021c modeliui 49
- Jungiklio veikimas 49
- Kilpinės rankenos sumontavimas priedas 49
- Surinkimas 49
- Tolygaus įjungimo funkcija 49
- Šoninės rankenos montavimas 49
- Darbas su šlifuojančiu pjovimo disku priedas 50
- Disko saugiklio uždėjimas ir nuėmimas 50
- Naudojimas 50
- Šlifavimas ir šlifavimas švitriniu popieriumi 50
- Šlifavimo disko multi disko priedas uždėjimas ir nuėmimas 50
- Anglinių šepetėlių keitimas 51
- Priedai 51
- Techninė priežiūra 51
- Tehnilised andmed 52
- Üldvaate selgitus 52
- Eü vastavusdeklaratsioon 54
- Ohutuse erijuhised 54
- Funktsionaalne kirjeldus funktsionaalne kirjeldus 56
- Hoiatus 56
- Hoidke juhend alles 56
- Aaspideme paigaldamine lisatarvik 57
- Elektrooniline funktsioon pidev kiirusekontroll mudelile ga5020c ga5021c ga6020c ga6021c 57
- Kokkupanek 57
- Külgkäepideme käepide paigaldamine 57
- Lüliti funktsioneerimine 57
- Sujuvkäivituse funktsioon 57
- Võllilukk 57
- Kettapiirde paigaldamine või eemaldamine 58
- Käiamise ja lihvimise režiim 58
- Lohkus keskosaga käiakettas multi diski tarvik paigaldamine või eemaldamine 58
- Töö abrasiivlõikekettaga lisatarvik 58
- Tööriista kasutamine 58
- Hooldus 59
- Süsiharjade asendamine 59
- Tarvikud 59
- Объяснения общего плана 60
- Технические характеристики 60
- Декларация о соответствии ес 62
- Специфические правила техники безопасности 62
- Предупреждени 65
- Сохраните данные инструкции 65
- Действие переключения 66
- Замок вала 66
- Описание функционирования 66
- Функция плавного запуска 66
- Электронная функция постоянный контроль скорости в модели ga5020c ga5021c ga6020c ga6021c 66
- Монтаж 67
- Установка боковой рукоятки ручки 67
- Установка или снятие кожуха диска 67
- Установка или снятие шлифовального диска с вогнутым центром мультидиска дополнительная принадлежность 67
- Установка рамочной рукоятки принадлежность 67
- Выполнение работ с абразивным отрезным кругом принадлежность 68
- Замена угольных щеток 68
- Техобслуживание 68
- Шлифовка и зачистка 68
- Эксплуатация 68
- Принадлежности 69
- Makita corporation anjo aichi japan 72
Похожие устройства
- Makita GA9050 (168201) Инструкция по эксплуатации
- Makita HG5012K в кейсе (161129) Инструкция по эксплуатации
- Bosch GOF 1250 CE (0.601.626.000) Инструкция по эксплуатации
- Makita RP1801F (178307) Инструкция по эксплуатации
- Makita RT0700C(X2) (171195) Инструкция по эксплуатации
- Bosch GEX 150 AC (0.601.372.768) Инструкция по эксплуатации
- Makita BO5041K (169567) Инструкция по эксплуатации
- Bosch GSR 180-Li + фонарь GLI 18V-300 (0.601.9F8.103) Инструкция по эксплуатации
- Makita DDF453RFE (178361) Инструкция по эксплуатации
- Makita DF333DWAE (194008) Инструкция по эксплуатации
- Makita DDF480RME (180854) Инструкция по эксплуатации
- Bosch GST 150 CE (0.601.512.000) Инструкция по эксплуатации
- Bosch PST 18 Li без АКБ и ЗУ (0.603.011.020) Инструкция по эксплуатации
- Bosch PST 900 PEL + 10 пилок (0.603.3A0.201) Инструкция по эксплуатации
- Kenwood DPX-502 UY Инструкция по эксплуатации
- Bosch GST 12V-70 (0.601.5A1.000) Инструкция по эксплуатации
- Makita 4326 (152051) Инструкция по эксплуатации
- Makita 4350CT (152630) Инструкция по эксплуатации
- Bosch GKS 12V-26 без АКБ и ЗУ (0.601.6A1.001) Инструкция по эксплуатации
- Kenwood KVT-522 DVDY Инструкция по эксплуатации