![Icom IC-F310S [9/20] Operation](/img/pdf.png)
Icom IC-F310S [9/20] Operation
![Icom IC-F310S [9/20] Operation](/views2/1074557/page9/bg9.png)
■ Channel selection
Several types are available, and the channel selection method
may differ according to your system set up.
NON-BANK TYPE:
Push the []/[]keys to select the desired operating
channel, in sequence; or,
push one of the [
CH 1] to [CH 4] keys to select these channels
directly.
BANK-TYPE:
Push [
BANK] to select the desired bank number.
AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning
the power ON, the transceiver automatically starts scanning.
Scanning stops when receiving a call or when taking the mi-
crophone off hook.
■ Turning power ON
q Push [K
I
] to turn the power ON.
• A power-up alert tone sounds for
about 1 sec. and an opening mes-
sage may appear.
w If the transceiver is programmed
for a start up passcode, input
digit codes as directed by your
System operator.
• The keys in the diagram below can
be used for password input:
• The transceiver detects numbers in the same block as identical.
Therefore “1234” and “6789” are the same.
e When the “PWORD” indication does not clear after inputting
4 digits, the input code number may be incorrect. Turn
power off and start over in this case.
OPERATION
2
6
Opening message may
differ depending on the
pre-setting.
Input your password if
this display appears.
KEY
NUMBER
P0 P1 P2 P3
0
5
1
6
2
7
3
8
4
9
Содержание
- If320 if310 1
- If410 if420 1
- Instruction manual 1
- Uhf transceiver 1
- Vhf transceiver 1
- Cautions important 2
- Explicit definitions 2
- R warning neve 2
- Read all instruction 2
- Save this instruction manual 2
- Be careful 3
- Connection and maintenance 9 12 3
- Important i explicit definitions i cautions i table of contents ii 3
- Operate the transceiver without running the vehicle s engine the vehicle s battery will quickly run out if the trans ceiver is in transmission while the vehicle s engine off 3
- Operation 6 8 3
- Optional smartrunk ii operation 13 15 3
- Options 16 3
- Panel description 1 5 3
- Placing the transceiver against walls this will ob struct heat dissipation 3
- Placing the transceiver in excessively dusty envi ronments 3
- Table of contents 3
- The transceiver will become hot when operating continuously for long periods 3
- The use of chemical agents such as benzine or al cohol when cleaning as they damage the transceiver sur faces 3
- Use or place the transceiver in areas with tem peratures below 30 c or above 60 c or in areas subject to direct sunlight such as the dashboard 3
- I front panel 4
- Panel description 4
- I function display 5
- Panel description 5
- I programmable function keys 6
- Panel description 6
- Panel description 7
- Panel description 8
- 5 1 6 2 7 3 8 4 9 9
- I channel selection 9
- I turning power on 9
- Operation 9
- D transmitting notes 10
- I receiving and transmitting 10
- Important 10
- Operation 10
- D dtmf transmission 11
- D tx code channel selection 11
- D tx code number selection 11
- Operation 11
- Connection and maintenance 12
- I rear panel and connection 12
- Connection and maintenance 13
- I supplied accessories 13
- Connection and maintenance 14
- I mounting the transceiver 14
- I optional ut 96 ut 105 instal lation 14
- A key element in the performance of any communication sys tem is an antenna ask your dealer about antennas and the best places to mount them 15
- Avoid the use of solvents such as benzene or al cohol as they may damage transceiver surfaces 15
- Connection and maintenance 15
- I antenna 15
- I cleaning 15
- I fuse replacement 15
- I optional opc 617 installation 15
- If the transceiver becomes dusty or dirty wipe it clean with a dry soft cloth 15
- Install the opc 617 as shown below 15
- Two fuses are installed in the supplied dc power cable if a fuse blows or the transceiver stops functioning track down the source of the problem if possible and replace the dam aged fuse with a new rated one 15
- D calling another local system subscriber 16
- D placing a telephone call 16
- D receiving a call 16
- I smartrunk ii and conventional modes 16
- I smartrunk ii operation 16
- Optional smartrunk ii operation 16
- D emergency call 17
- D last number redial 17
- D memory speed dialing 17
- D programming memory speed dial 17
- D ptt dispatch operation 17
- D system busy indication 17
- D terminating a call 17
- D turbo speedial 17
- Optional smartrunk ii operation 17
- D clear channel alerting 18
- Optional smartrunk ii operation 18
- Options 19
- 9 16 kamihigashi hirano ku osaka 547 0002 japan 20
Похожие устройства
- Samsung WF702B2BBWQ Инструкция по эксплуатации
- Ardo C 631EB Инструкция по эксплуатации
- Icom IC-F320S Инструкция по эксплуатации
- Samsung WF702U2BBWQ Инструкция по эксплуатации
- Ardo A 631EB Инструкция по эксплуатации
- Icom IC-410S Инструкция по эксплуатации
- Hotpoint-Ariston ECOT7F 129 (EU) Инструкция по эксплуатации
- Ardo A 531EB Инструкция по эксплуатации
- Icom IC-F420S Инструкция по эксплуатации
- Indesit MIDK 6505 (CIS) Инструкция по эксплуатации
- Ardo KTLE 6640 EF Инструкция по эксплуатации
- Icom IC-F510 Инструкция по эксплуатации
- Hotpoint-Ariston AVDK 7129 (CIS) Инструкция по эксплуатации
- Ardo KA 5640 EE Инструкция по эксплуатации
- Icom IC-F610 Инструкция по эксплуатации
- Hotpoint-Ariston MVDB 8614 SX (CIS) Инструкция по эксплуатации
- Ardo KC 640 EF Инструкция по эксплуатации
- Icom IC-F520 Инструкция по эксплуатации
- Hotpoint-Ariston QVDE 117149 SS (CIS) Инструкция по эксплуатации
- Ardo KA 640 EE Инструкция по эксплуатации
Скачать
Случайные обсуждения