![Daikin FTD20JEVLK [15/24] Additional charge](/img/pdf.png)
Daikin FTD20JEVLK [15/24] Additional charge
![Daikin FTD20JEVLK [15/24] Additional charge](/views2/1785242/page15/bgf.png)
English
1-13
Additional refrigerant charge [g] per additional 1m length as tabulated (For R22 models)
IR Signal Receiver
When an infrared remote control operating signal has been
transmitted, the signal receiver on the indoor unit will respond
as below to conÀ rm acceptance of the signal transmission.
LED Indicator Lights for Cooling Unit
IR Receiver
Cooling Unit / Heat Pump Unit
The table shows the LED indicator lights for the air conditioner
unit under normal operation and fault conditions.
The LED indicator lights are located at the right bottom of
the air conditioner unit.
The heat pump units are equipped with an “auto” mode
sensor whereby it will provide reasonable room temperature
by switching automatically to either “cool” or “heat” mode
according to the temperature set by the user.
ON/OFF
Cool/Heat
Timer
Sleep
ON/OFF switch
Additional Charge
The refrigerant is pre-charged in the outdoor unit. If the piping length is less than 7.5m, then additional charge after vacuuming
is not necessary. If the piping length is more than 7.5m, then use the additional charge value as indicated in the table.
IR Receiver
INDICATOR LIGHTS
Indoor FTD20JEVLK FTYD20JEVLK FTD25JEVLK FTYD25JEVLK
Outdoor RD20JEVLK RYD20JEVLK RD25JEVLK RYD25JEVLK
Additional charge [g/m] 22 22 55 55
ON to OFF 1 Long Beep
OFF to ON
Pump down/Cool force on
2 Short Beep
Others 1 Short Beep
Example:
FTD20JEVLK & RD20JEVLK with 12m piping length, additional piping length is 4.5m. Thus,
Additional charge = 4.5[m] x 22[g/m]
= 99.0[g]
1 IM-WMJ-0211(0)_DAIKIN (SASO)-E13 13 6/1/11 12:09:54 PM
Содержание
- Installation manual 1
- R22 split series 1
- All dimensions are in mm 3
- Dimension model a b c d e f g h i j k l m 3
- English 3
- Front view 3
- Ft y d20 25jevlk 1065 310 228 190 173 61 40 45 48 91 219 580 45 3
- Indoor unit 3
- Installation plate ft y d20 25jevlk 3
- Outline and dimensions 3
- Side view 3
- Top view 3
- Outdoor unit 4
- Disposal requirement your air conditioning product is marked with this symbol this means that electrical and electronic products shall not be mixed with unsorted household waste do not try to dismantle the system yourself the dismantling of the air conditioning system treatment of the refrigerant of oil and of other parts must be done by a quali ed installer in accordance with relevant local and national legislation air conditioners must be treated at a specialized treatment facility for re use recycling and recovery by ensuring this product is disposed of correctly you will help to prevent potential negative consequences for the environment and human health please contact the installer or local authority for more information batteries must be removed from the remote controller and disposed of separately in accordance with relevant local and national legislation 5
- English 5
- Installation manual 5
- Notice 5
- Safety precautions 5
- This manual provides the procedures of installation to ensure a safe and good standard of operation for the air conditioner unit special adjustment may be necessary to suit local requirement before using your air conditioner please read this instruction manual carefully and keep it for future reference 5
- Warning caution 5
- Important 6
- Unpacking procedures 6
- English 7
- Installation diagram 7
- Installation of the outdoor unit 7
- Condensed water disposal of outdoor unit heat pump unit only 8
- Installation of the indoor unit 8
- Left side left back or left bottom piping 8
- Right side right back or right bottom piping 8
- The indoor unit must be installed in such a way so as to prevent short circuit of the cool discharged air with the hot return air please follow the installation clearance shown in the gure do not place the indoor unit where there could be direct sunlight shining on it also this location must be suitable for piping and drainage and be away from doors or windows 8
- The refrigerant piping can be routed to the unit in a number of ways left or right from the back of the unit by using the cut out holes on the casing of the unit see gure bend the pipes carefully to the required position in order to align it with the holes for the side and bottom hold the bottom of the piping and then position it to the required direction see gure the condensation drain hose can be taped to the pipes 8
- There are 2 holes on the base of outdoor unit for condensed water to ow out insert the drain elbow to one of the holes to install the drain elbow rst insert one portion of the hook to the base portion a then pull the drain elbow in the direction shown by the arrow while inserting the other portion to the base after installation check to ensure that the drain elbow clings to base rmly if the unit is installed in a snowy and chilly area condensed water may freeze in the base in such case please remove plug at the bottom of unit to smooth the drainage 8
- Caution 9
- Do not install the unit at altitude over 2000m for both indoor and outdoor 9
- English 9
- Ensure that the wall is strong enough to withstand the weight of the unit otherwise it is necessary to reinforce the wall with plates beams or pillars use the level gauge for horizontal mounting and x it with for ft y d20 25jevlk in case the rear piping draws out drill a hole 65mm in diameter with a cone drill slightly lower on the outside wall see gure 9
- Hole with cone drill 9
- Hook the claws of the bottom frame to the mounting plate 9
- Hook the indoor unit onto the upper portion of the installation plate engage the two hooks at the rear top of the indoor unit with the upper edge of the installation plate ensure that the hooks are properly seated on theinstallation plate by moving it to the left and right 9
- How to attach the indoor unit 9
- How to remove the indoor unit 9
- Mount the unit onto the installation plate 9
- Mounting installation plate 9
- Push up the marked area at the lower part of the front grille to release the claws 9
- Recommended mounting plate retention spots and dimensions 9
- The indoor drain pipe must be in a downward gradient for smooth drainage avoid situations that are likely to cause water to leak 9
- Water drainage 9
- Water drainage piping 9
- Allowable piping length 10
- Refrigerant piping 10
- English 11
- Piping connection to the units 11
- Piping works and flaring technique 11
- Cooling unit 12
- Cooling unit single phase 12
- Electrical wiring connection 12
- Heat pump unit single phase 12
- English 13
- Charge operation 14
- Vacuuming and charging 14
- Vacuuming the piping and the indoor unit 14
- Additional charge 15
- Cooling unit heat pump unit 15
- English 15
- Indicator lights 15
- Ir signal receiver 15
- Led indicator lights for cooling unit 15
- Led indicator lights normal operation and fault conditions for cooling heat pump unit 16
- Note the unit will not detect sensor missing when the compressor is on 16
- Air conditioner unit operation 17
- Air flow control 17
- Attention 17
- Dry mode 17
- English 17
- Fan speed and rated cooling capacity 17
- Frost prevention 17
- Heat mode for heat pump unit only 17
- Notes on flaps and louvers angles 17
- Operating range 17
- Overheating protection for heat pump unit only 17
- Air filter 18
- Caution 18
- Clean or replace each lter 18
- Open the front panel 18
- Pull out the air lters 18
- Set the air lter and bio lter with bacteriostatic virustatic functions as they were and close the front panel 18
- Take off the bio lter with bacteriostatic virustatic functions 18
- Attach the front panel 19
- Caution 19
- English 19
- Open the front panel 19
- Remove the front panel 19
- Service and maintenance 19
- For any enquiries on spare part please contact your authorized dealer when any malfunction of the air conditioner unit is noted immediately switch off the power supply to the unit check the following fault conditions and causes for some simple troubleshooting tips 20
- If the fault persists please call your local dealer serviceman 20
- Troubleshooting 20
- When the unit is not to be used for an extended long period of time 20
- English 21
- Specifications 21
Похожие устройства
- Daikin FTD25JEVLK Инструкция по эксплуатации
- Daikin FTD25JEVLK Инструкция по монтажу
- Daikin FTYD20JEVLK Инструкция по монтажу
- Daikin FTYD20JEVLK Инструкция по эксплуатации
- Daikin FTYD25JEVLK Инструкция по монтажу
- Daikin FTYD25JEVLK Инструкция по эксплуатации
- Daikin FTYNV20AV1 Инструкция по эксплуатации
- Daikin FTYNV25AV1 Инструкция по эксплуатации
- Daikin FTYNV35AV1 Инструкция по эксплуатации
- Daikin FTYNV50AV1 Инструкция по эксплуатации
- Daikin FTYNV60AV1 Инструкция по эксплуатации
- Daikin RYNV20AV1 Инструкция по эксплуатации
- Daikin RYNV25AV1 Инструкция по эксплуатации
- Rinnai BR-RE18 Технический паспорт
- Rinnai BR-RE18 Инструкция по эксплуатации
- Rinnai BR-RE24 Технический паспорт
- Rinnai BR-RE24 Инструкция по эксплуатации
- Rinnai BR-RE30 Технический паспорт
- Rinnai BR-RE30 Инструкция по эксплуатации
- Rinnai BR-RE36 Технический паспорт