Daikin RZQ100B7W1B [40/48] Field wiring 3

Daikin RZQ200B7W1B [40/48] Field wiring 3
Outdoor Units • R410A • RZQ-B
Split Sky Air • Outdoor Units
38
2
8
8 Wiring diagram
2TW26766-1
RZQ100-125-140B7W1B
A1P Printed circuit board
A2P Printed circuit board (INV)
BS1 Push button switch (forced defrost / pump down)
C1-C2-C3 Capacitor
DS1 Dip switch
F1U (A2P) Fuse (T 6,3A/250V)
F2U Fuse (T 6,3A/250V)
F3U Fuse (B 10A/250V)
F4U Fuse (B 10A/250V)
HAP (A1P) Light emitting diode (service monitor green)
HAP (A2P) Light emitting diode (service monitor green)
H1P (A1P) Light emitting diode (service monitor red)
K1M(A2P) Magnetic contactor
K1R(A1P) Magnetic relay (Y1S)
K2R(A1P) Magnetic relay (Y2S)
K3R(A1P) Magnetic relay (E1HC)
K4R, K5R Magnetic relay
L1R Reactor
M1C Motor compressor
M1F Motor fan
PS Power circuit
Q1DI Earth leakage breaker (30mA)
R1-R2 Resistor
R1T Thermistor (air)
R2T Thermistor (coil)
R3T Thermistor (discharge pipe)
R4T Thermistor (suction pipe)
R5T Thermistor (power module)
S1PH Pressure switch (high)
S1NPL Pressure sensor (low)
RC Signal receiver circuit
TC Signal transmission circuit
V1R Power module
V2R-V3R Diode module
V1T IGBT
X6A Connector (Option)
X1M Terminal strip
Y1E Expansion valve
Y1S 4-way valve
Y2S Solenoid valve
Z1C, Z2C
Z3C, Z4C
Noise filter
Z1F Noise filter
Z1F Noise filter (with surge absorber)
L : Live
N : Neutral
: Field wiring
: Protective earth (screw)
: Wire clamp
: Terminal
: Connector
: Relay connector
Colours
BLK: Black / ORG: Orange / BLU: Blue /
WHT: White / RED: Red / YLW:Yellow /
BRN: Brown / GRN: Green
NOTES:
1. Refer to the optional manual, for connection
wiring to X6A.
2. Confirm the method of setting the selector
switches (DS1) by service manual. When the
unit is shipped by factory all switches are set
to be off.
Outdoor
NOTE 1.
Indoor
El. comp. assy front
View A
ON
OFF
Reactor box
2TW26566-1
RZQ200-250B7
A1P-A5P Printed circuit board
A1P Main
A2P Inverter
A3P Fan motor
A4P Noise filter
A5P current sensor
BS1-BS5 Push button switch
Mode, set, return, test, forced defrost
C2-C5,C63,C65 Capacitor
DS1 Dip switch
E1HC, E2HC Crankcase heater
F1U Fuse (250V, 5A
j
B
) (A4P)
F1U, F2U Fuse (250V, 10A
j
B
) (A1P)
F5U Field fuse
H1P-H7P Pilot lamp (Pilotlamp service monitor - orange)
Prepare test--------Flickering
[H2P] Malfunction detection---Light up
HAP Pilot lamp (Pilotlamp service monitor - green)
K1 Magnetic relay
K2S Magnetic relay (M2C)
K2 Magnetic contactor (M1C)
K2M Magnetic contactor (M2C)
K1R-K7R Magnetic relay
K1R K2M (A1P)
K2R Y1S
K3R E1HC (A1P)
K4R E2HC (A1P)
K5R Y2S
K6R Y3S
K7R Y4S
L1R Reactor
M1C, M2C Motor compressor
M1F Motor fan
PS Power circuit
Q1DI Earth leakage breaker (max. 30mA)
Q1RP Phase reversal detect circuit
R10 Resistor (current sensor)
R50, R59 Resistor
R95 Resistor (current limiting)
R1T, R32T Thermistor
R1T Air (A1P)
R32T M2C Discharge
R1T Fin type (A2P)
R4T Coil-deicer
R2T Suction
R5T Coil-outlet
R31T M1C Discharge
S1NPH Pressure sensor (high)
S1NPL Pressure sensor (low)
S1PH, S2PH Pressure switch (high)
T1A current sensor
T1R Transformer(230V/20V)
V1CP, V2CP Safety devices input
V1R, V2R Power module (A2P)
V1R Power module (A3P)
X1M Terminal strip (Control) (A1P)
X2M Terminal (Power supply indoor)
X3M Terminal (Control)
X4M Terminal strip (Power supply)
Y1E Electronic expansion valve (Main)
Y2E Electronic expansion valve (Subcool)
Y1S-Y4S Solenoid valve
Y1S 4-way valve
Y2S Hot gas
Y3S Receiver gas purge
Y4S Liquid pipe
Z1C, Z5C Noise filter (ferrite core)
Z1F Noise filter (with surge absorber)
Option connectors
X36A Connector adaptor power supply
Notes:
1. This wiring diagram only applies to the outdoor unit
2.
: Field wiring
3.
: Terminal strip : Connector
: Terminal : Protective earth (screw)
4. For use of the option adaptor, how to use BS1 BS5 and
DS1 switch and connection to X1M(A1P) or X3M refer to
the installation manual.
5. Do not operate the unit by short-circuiting protection
device S1PH, S2PH
6. BLK: Black / WHT: White / RED: Red / BLU: Blue
GRY: Grey / BRN: brown / GRN: Green / YLW: Yellow /
PNK: Pink
Front layer
(NOTE 4)
Indoor
(NOTE 4)
Position in
switch box
ON
OFF
Rear layer
XXX = Color of PCB connector
YYY = (Marked) color of wire connector
ZZZ = Color of wire
Power supply
400V 3N 50Hz
Detail of M1C, M2C
(NOTE 4)

Содержание

Скачать