Home
Главная
Hitachi
Шлифовальная Машина
G13SR3
Инструкция по эксплуатации Страница: 5

Hitachi G13SR3 [5/53] English

English

SPECIFICATIONS

*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Wrench ........................................................................1

(2) Side handle ................................................................ 1

Standard accessories are subject to change without

notice.

APPLICATIONS

䡬

Removal of casting fin and finishing of various types

of steel, bronze and aluminum materials and castings.

䡬 Grinding of welded sections or sections cut by

means of a cutting torch.

䡬 Grinding of synthetic resins, slate, brick, marble, etc.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Fitting and adjusting the wheel guard

The wheel guard is a protective device to prevent

injury should the depressed center wheel shatter

during operation. Ensure that the guard is properly

fitted and fastened before commencing grinding

operation.

By slightly loosening the setting screw, the wheel

guard can be turned and set at any desired angle

for maximum operational effectiveness. Ensure that

the setting screw is thoroughly tightened after

adjusting the wheel guard.

5. Ensure that mounted wheels and points are fitted

in accordance with the manufacturer’s instructions.

Ensure that the depressed center wheel to be utilized

is the correct type and free of cracks or surface

defects. Also ensure that the depressed center wheel

is properly mounted and the wheel nut is securely

tightened, Refer to the section on “ASSEMBLING

AND DISASSEMBLING THE DEPRESSED CENTER

WHEEL”

Ensure that blotters are used when they are provided

with the bonded abrasive product and when they

are required.

Model G10SR3 G12SR3 G13SR3

Voltage (by areas)* (110V, 120V, 220V, 230V, 240V)

Power Input* 730 W

No-load speed 10000 min

-1

Outer dia. × hole dia. 100 × 16 mm 115 × 22 mm 125 × 22 mm

Wheel

Peripheral speed 72 m/s 80 m/s

Weight (Only main body) 1.4 kg

GENERAL SAFETY INSTRUCTIONS FOR

GRINDERS

– Check that speed marked on the wheel is equal to

or greater than the rated speed of the grinder;

– Ensure that the wheel dimensions are compatible

with the grinder;

– Abrasive wheels shall be stored and handled with

care in accordance with manufacturer’s instructions;

– Inspect the grinding wheel before use, do not use

chipped, cracked or otherwise defective products;

– Ensure that mounted wheels and points are fitted

in accordance with the manufacturer’s instructions;

– Ensure that blotters are used when they are provided

with the bonded abrasive product and when they

are required;

– Ensure that the abrasive product is correctly mounted

and tightened before use and run the tool at no-

load for 30 s in a safe position, stop immediately

if there is considerable vibration or if other defects

are detected. If this condition occurs, check the

machine to determine the cause;

– If a guard is equipped with the tool never use the

tool without such a guard;

– Do not use separate reducing bushings or adapters

to adapt large hole abrasive wheels;

– For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length;

– Check that the work piece is properly supported;

– Do not use cutting off wheel for side grinding;

– Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite flammable

substances;

– Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, first disconnect the tool

from the mains supply (use non metallic objects)

and avoid damaging internal parts;

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves,

helmet and apron should be worn;

– Pay attention to the wheel that continues to rotate

after the tool is switched off.

Hitachi G13SR3 [5/53] English

Содержание

Похожие устройства