Home
Главная
Vitek
Кофеварка рожкового типа
VT-1518
Инструкция по эксплуатации Страница: 4

Vitek VT-1518 [4/32] English

ENGLISH

service or similar qualified personnel to avoid

danger.

• Do not repair the unit by yourself. Do not dis-

assemble the unit by yourself, if any mal-

function is detected or after it was dropped,

unplug the unit and apply to any authorized

service center from the contact address list

given in the warranty certificate and on the

website www.vitek.ru.

• Transport the unit in the original packaging

only.

• Keep the unit out of reach of children and

people with disabilities.

THE UNIT IS INTENDED FOR HOUSEHOLD USE

ONLY, ITS COMMERCIAL USAGE AND USAGE

IN PRODUCTION AREAS AND WORK SPACES IS

PROHIBITED.

BEFORE THE FIRST USE

After the unit transportation or storage at low

temperature keep it for at least three hours

at room temperature before switching on.

– Take the coffee maker out of the package and

remove the packaging materials.

– Check the unit for damages; do not use it in

case of damages.

– Make sure that operating voltage of the cof-

fee maker corresponds to the voltage of your

mains.

– The unit is intended for operation with AC sys-

tem and 50 or 60 Hz frequency. The unit does

not need any additional settings for operating

with the required nominal frequency.

BEFORE USING THE UNIT

• Make sure that the operation mode switch (2)

is set to the position «RELEASE OFF».

• Before using the coffee maker for the first

time, wash all removable parts (6, 10) with

warm water and neutral detergent, rinse and

dry them.

• Before switching the unit on, make sure that

the mains voltage corresponds to the voltage

specified on the unit body.

• Unscrew the lid (1) turning it counterclock-

wise.

• Pour about 240 ml of water into a cup of suit-

able height (pic. 1).

• Pour the water from the cup into the water

tank.

• Thread the lid (1) rotating it clockwise (pic. 1).

• Install the coffee filter (10) into the holder (6),

do not add ground coffee to the filter (10).

• Install the filter holder (6) into the coffee

maker. The holder (6) ledges should match

the grooves on the boiler, after that turn the

filter holder (6) handle (8) to the right until

bumping «LOCK» (pic. 2).

• Place the cup on the tray (9).

• Insert the power plug into the socket.

• Switch the coffee maker on by setting the

operation mode switch (2) to the position

« », the light indicator (3) will light up, the

heating element will switch on and water will

start pouring into the cup under pressure.

• After water pouring set the operation mode

switch (2) to the position «RELEASE OFF»

to switch the coffee maker off and to release

the pressure.

• To wash the cappuccinator pipe unscrew the

lid (1), fill a cup with water (no more than

50 ml), pour the water to the water tank and

screw the lid (1).

• Place a suitable cup under the tip (5).

• Switch the coffee maker on by setting the

operation mode switch (2) to the position

« », the indicator (3) will light up, the heat-

ing element will switch on and the steam

under pressure will be released from the

tip (5).

• Set the operation mode switch (2) to the posi-

tion «RELEASE OFF» to switch the coffee

maker off and to release the pressure.

• The coffee maker is ready to use.

ATTENTION!

– Do not remove the filter holder (6) during cof-

fee maker operation.

MAKING ESPRESSO

Attention!

When making coffee do not leave the operat-

ing coffee maker unattended, as it is necessary

to watch the cup being filled with ready coffee!

• Make sure that the operation mode switch (2)

is set to the position «RELEASE OFF».

• Unscrew the lid (1) turning it counterclock-

wise.

• Pour water into a cup of suitable height

depending on the necessary amount of ready

coffee, but not exceeding 240 ml.

• Pour the water from the cup into the water

tank (pic. 1).

• Thread the lid (1) rotating it clockwise (pic. 1).

IM VT-1518.indd 4 12/24/19 12:17 PM

Vitek VT-1518 [4/32] English

Содержание

Похожие устройства