Hander HCS-180N [5/70] Kickback operator prevention
![Hander HCS-180N [5/70] Kickback operator prevention](/views2/1087806/page5/bg5.png)
9
GB
KICKBACK-CAUSES
• Kickback is a sudden reaction to a pinched, bound
or misaligned saw blade, causing an uncontrolled saw
to lift up and out of the workpiece toward the operator
• When the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor reac-
tion drives the unit rapidly back toward the operator
• If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the wood causing the blade to climb out
of the kerf and jump back towards operator
KICKBACK - OPERATOR PREVENTION
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below
• Maintain a fi rm grip with both hands on the saw
and position your arms to resist kickback forces;
position your body to either side of the blade, but
not in line with the blade (kickback could cause the
saw to jump backwards, but kickback forces can be
controlled by the operator, if proper precautions are
taken)
• When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to
a complete stop; never attempt to remove the saw
from the work or pull the saw backwards while the
blade is in motion or kickback may occur (investi-
gate and take corrective actions to eliminate the cause
of blade binding; avoid cutting nails or screws)
• When restarting a saw in the workpiece, centre
the saw blade in the kerf and check that saw teeth
are not engaged into the material (if saw blade is
binding, it may walk up or kickback from the workpiece
as the saw is restarted)
• Support large panels to minimize the risk of
blade pinching and kickback (large panels tend to
sag under their own weight; supports must be placed
under the panel on both sides, near the line of cut and
near the edge of the panel)
• Do not use a dull or damaged blade (unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback)
• Blade depth and bevel adjusting locking levers
must be tight and secure before making cut (if blade
adjustment shifts while cutting, it may cause binding
and kickback)
• Use extra caution when making a plunge cut into
existing walls or other blind areas (the protruding
blade may cut objects that can cause kickback)
WARNING
• Check lower guard for proper closing before
each use
• Do not operate the saw if lower guard does not
move freely and close instantly
• Never clamp or tie the lower guard into the open
position
• If saw is accidentally dropped, lower guard may be
bent; raise the lower guard with the retracting handle
and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut
• Check the operation of the lower guard spring;
if the guard and the spring are not operating prop-
erly, they must be serviced before use (lower guard
may operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris)
• Lower guard should be retracted manually only
for special cuts such as plunge cuts and compound
cuts; raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released (for all other sawing, the lower guard
should operate automatically)
• Always observe that the lower guard is cover-
ing the blade before placing saw down on bench
or fl oor (an unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path;
be aware of the time it takes for the blade to stop after
switch is released)
• Avoid damage that can be caused by screws, nails
and other elements in your workpiece; remove them be-
fore you start cutting
• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
• Use completely unrolled and safe extension cords
with a capacity of 16Amps (U.K. 13Amps)
• In case of jamming or electrical or mechanical mal-
function, immediately switch off the tool and disconnect
the plug
• The SBM Group can assure fl awless functioning of
the tool only when original accessories are used
• Use only accessories with an allowable speed
matching at least the highest no-load speed of the tool
• Never use the tool without the original protection
guard system
• This tool should not be used by people under the age
of 16 years
• The noise level when working can exceed 85 dB(A);
wear ear protection
• If the cord is damaged or cut through while working,
do not touch the cord, but immediately disconnect the
plug
• Never use tool when cord is damaged; have it re-
placed by a qualifi ed person
• Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
• This tool is not suitable for wet cutting
• After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
• Never use circular saw blades made of high speed
steel (HSS)
• Never use grinding/cutting discs with this tool
• Do not work materials containing asbestos (as-
bestos is considered carcinogenic)
• Take protective measures when during work
dust can develop that is harmful to one’s health,
combustible or explosive (some dusts are considered
carcinogenic); wear a dust mask and work with dust/
chip extraction when connectable
• Do not attempt to cut extremely small workpieces
• Remove all obstacles on top of as well as under-
neath the cutting path before you start cutting
• Do not work overhead with the tool
• Only use a saw table provided with a switch that pre-
vents restarting of the motor after interruption of volt-
age
• Only use a saw table provided with a kerf guide
Содержание
- Hcs 180n 1
- Deutsch 2
- Kreissäge 2
- Achtung 3
- Circular saw 4
- English 4
- Check the operation of the lower guard spring if the guard and the spring are not operating prop erly they must be serviced before use lower guard 5
- Kickback causes 5
- Kickback operator prevention 5
- May operate sluggishly due to damaged parts gummy deposits or a build up of debris 5
- Warning 5
- Français 6
- Scie circulaire 6
- Attention 7
- Retour arrière causes 7
- Retour arrière prévention 7
- Español 8
- Sierra circular 8
- Acción de retroceso causas 9
- Acción de retroceso prevención por parte del operario 9
- Atención 9
- Mantenimiento 10
- Medio ambiente 10
- Português 11
- Serra circular 11
- Atenção 12
- Italiano 13
- Sega circolare 13
- Attenzione 14
- Retroazione cause 14
- Retroazione prevenzione dell operatore 14
- Ambiente 15
- Manutenzione 15
- Cirkelzaag 16
- Nederlands 16
- Let op 17
- Rundsav 18
- Brugerens forholdsregler mod tilbageslag 19
- Tilbageslag årsager 19
- Vigtigt 19
- Cirkelsåg 20
- Svenska 20
- Kast anledningar 21
- Kast förhindrande från operatörens sida 21
- Sirkelsag 22
- Riktig bruk for å hindre tilbakeslag 23
- Tilbakeslag årsaker 23
- Pyörösaha 24
- Huomio 25
- Takapotku estotoimia käyttäjän turvallisuuden suojelemiseksi 25
- Takapotku syitä 25
- Ketassaag 26
- Keskkonnakaitse 27
- Saeketaste kasutamine 27
- Seade tuleb kohe välja lülitada kui 27
- Tehniline teenindamine ja hooldus 27
- Töö käigus 27
- Cirkulārais zāģis 28
- Diskinis pjūklas 29
- Lietuvių 29
- Aplinkos apsauga 30
- Dirbant su prietaisu 30
- Nedelsdami išjunkite prietaisą jei 30
- Pjovimo diskų naudojimas 30
- Techninis aptarnavimas ir priežiūra 30
- Пила циркулярная 31
- Русский 31
- Следует немедленно выключить инстру мент при 32
- Техническое обслуживание и уход 32
- Шеңберсызғы ара 33
- Келесі жағдайларда бұйымды дереу өшіру қажет 34
- Техникалық қызмет ету мен күтім 34
- Пила циркулярна 35
- Українська 35
- Слід негайно вимкнути інструмент при 36
- Технічне обслуговування та догляд 36
- Piła tarczowa 37
- Polski 37
- Konserwacja 38
- Okružní pila 39
- Zpětný vrh ochranná opatření 40
- Zpětný vrh příčiny 40
- Kružna testera 41
- Srpski 41
- Trzanje mere predostožnosti koje preduzima operater 42
- Trzanje uzroci 42
- Upozorenje 42
- Kézi körfűrész 43
- Magyar 43
- Figyelem 44
- Visszaütés megelozés a szerszám kezeloje részérol 44
- Visszaütés okok 44
- Karbantartás 45
- Környezetvédelem 45
- Ferăstrău circular 46
- Română 46
- Atenţi 47
- Krožna žaga 48
- Slovenski 48
- Opozorilo 49
- Povratni sunek preprečitev uporabnika 49
- Povratni sunek vzroki 49
- Hrvatski 50
- Kružna pila 50
- Hr bos 51
- Povratni udar sprječavanje od strane osobe koja pili 51
- Povratni udar uzroci 51
- Upozorenje 51
- Δισκοπρίονο 52
- Εισαγωγη 52
- Ελληνικά 52
- Αιτία και λάβετε τα απαιτούμενα μέτρα για την εξουδετέρωση της αιτίας του σφηνώματος του δί σκου αποφεύγετε την κοπή καρφιών ή βιδών 53
- Αν κλωτσήσει το δισκοπρίονο μπορεί να πεταχτεί προς τα πίσω αλλά ο χειριστής μπορεί να ελέγξει τις δυνάμεις ενός ενδεχόμενου κλωτσήμα τος αν λάβει τα κατάλληλα προληπτικά μέτρα 53
- Κατάλληλοι οι ροδέλες και ο κοχλίας του δίσκου έχουν σχεδιαστεί ειδικά για το δισκοπρίονο σας για την καλύτερη δυνατή απόδοση και ασφάλεια λει τουργίας 53
- Κλωtσημα αitiεσ 53
- Κλωτσημα προφυλαξεσ χεριστη 53
- Οι δίσκοι κοπής που δεν εφαρμόζουν σωστά στο δισκοπρίονο θα περιστρέφονται εκκε ντρικά με αποτέλεσμα να χάσετε τον έλεγχο του εργαλείου 53
- Παράλληλες κοπές έτσι αυξάνεται η ακρί βεια κοπής και μειώνεται η πιθανότητα σφηνώματος του δίσκου 53
- Προειδοποίησ 53
- Το κλώτσημα είναι μια απότομη αντίδραση προκαλούμενη από έναν σφηνωμένο μπλοκαρι σμένο ή μη ευθυγραμμισμένο δίσκο που έχει ως αποτέλεσμα το δισκοπρίονο να μην βρίσκεται πια υπό τον έλεγχο του χειριστή και να εκσφενδονίζεται προς τα επάνω έξω από το κομμάτι εργασίας και προς το μέρος του χειριστή όταν ο δίσκος έχει σφηνώσει ή μαγκώσει σφιχτά στον αρμό κοπής ο δίσκος μπλοκάρει και η κίνηση της μηχανής σπρώχνει το εργαλείο με μεγάλη τα χύτητα προς το μέρος του χειριστή σε περίπτωση που ο δίσκος παραμορφωθεί ή δεν είναι σωστά ευθυγραμμισμένος στην εγκοπή τα δόντια στο πίσω άκρο του δίσκου ενδέχεται να αρπάξουν την επάνω επιφάνεια του ξύλου με απο τέλεσμα ο δίσκος να βγει από τον αρμό κοπής και να πεταχτεί προς το μέρος του χειριστή 53
- Το κλώτσημα είναι το αποτέλεσμα της λανθασμέ νης χρήσης του εργαλείου και ή λανθασμένων διαδικασιών ή συνθηκών χειρισμού και μπορεί να αποφευχθεί με τη λήψη των παρακάτω προληπτι κών μέτρων 53
- Αμίαντο θεωρείται σαν καρκινογόνο υλικό 54
- Είδη σκόνης θεωρούνται καρκινογόνα να φοράτε μάσκα προστασίας σκόνης και να χρησιμο ποιείτε αναρρόφηση σκόνης ροκανιδιών γρεζιών 54
- Μην επιχειρείτε να κόψετε αντικείμενα πολύ μι κρών διαστάσεων αφαιρέστε όλα τα εμπόδια από την γραμμή κο πής πάνω και κάτω πριν ξεκινήσετε την κοπή μην εργάζεσθε με το εργαλείο κρατώντας το ψηλά πάνω από το κεφάλι σας χρησιμοποιείτε μόνο το τραπέζι εργασίας που διαθέτει διακόπτη που δεν επιτρέπει την επανεκκί νηση του κινητήρα από διακοπή ρεύματος χρησιμοποιείτε μόνο το τραπέζι εργασίας που διαθέτει καμπύλος οδηγός 54
- Περιβαλλον 54
- Συντηρηση 54
- Daire biçkisi 55
- Türkçe 55
- Di kka 56
- ﺔﻴﺑﺮﻌﻟ ﺔﻐﻠﻟ 58
- ﺮﺋ ﺮﻗ ﺎﺸﻨﻣ 58
- Exploded view hcs 180n 60
- Spare parts list hcs 180n 61
- 4 db a 65
- 4 db a 4 4 65
- 42 eec 2006 95 eec 2004 108 eec 65
- En 55014 1 2006 en 61000 3 2 2006 en 61000 3 11 200 en 55014 2 1997 a1 en 60745 1 2006 en 60745 2 5 2007 en 60825 1 1994 a1 a2 65
- Advertencia para la 66
- Anvisninger om miljøbeskyttelse dk 66
- Apkārtējās vides aizsardzība lv 66
- Aplinkos apsauga lt 66
- Avvertenze per la tutela dell ambiente it 66
- Do meio ambiente pt 66
- Environmental protection gb 66
- Hinweise zum umweltschutz de 66
- Indicações para a protecção 66
- Informations sur la 66
- Keskonnakaitse ee 66
- Miljøvern no 66
- Richtlijnen voor milieubescherming nl 66
- Ympäristönsuojelu fi 66
- Återvinning se 66
- A környezetvédelemmel kapcsolatos tudnivalók hu 67
- Indicaţii pentru protecţia mediului înconjurător ro 67
- Informacja dotycząca ochrony środowiska pl 67
- Napotki za zaščito okolja si 67
- Pokyny k ochraně životního prostředí сz 67
- Upute o zaštiti okolišai hr bos 67
- Uputstvo o zaštiti okoline cs 67
- Çevre koruma bilgileri tr 67
- Υποδείξεισ για την προστασία του περιβάλλοντοσ gr 67
- Вказівки по захисту 67
- Навколишнього середовища 67
- Указания по защите окружающей среды ru 67
- Қоршаған ортаны қорғау kz 67
Похожие устройства
- JVC LT-46S90B Инструкция по эксплуатации
- Microsoft Wireless Mobile 3000V2 Mouse Wireless Mobile 3000 Инструкция по эксплуатации
- Hander HEP-601 Инструкция по эксплуатации
- JVC LT-46Z70 Инструкция по эксплуатации
- Logitech M235 Blue Инструкция по эксплуатации
- Hander HEP-900R Инструкция по эксплуатации
- JVC LT-47GZ78 Инструкция по эксплуатации
- Hander HDG-140 Инструкция по эксплуатации
- Logitech M235 Crystal White Инструкция по эксплуатации
- JVC LT-47DV1 Инструкция по эксплуатации
- Hander HHG-1600 Инструкция по эксплуатации
- Microsoft 3000 Инструкция по эксплуатации
- JVC LT-Z26SX5 Инструкция по эксплуатации
- Hander HHG-2000K Инструкция по эксплуатации
- Asus RT-N12 D1 Инструкция по эксплуатации
- JVC LT-Z26SX4 Инструкция по эксплуатации
- E-Machines N-10 Инструкция по эксплуатации
- Upvel UR-344AN4G+ Инструкция по эксплуатации
- JVC LT-Z32SX4 Инструкция по эксплуатации
- Upvel UR-326N4G Инструкция по эксплуатации
Скачать
Случайные обсуждения