Home
Главная
BEST
Вытяжки
SPLIT 800 BLACK BHC84751BA
Инструкция по эксплуатации Страница: 13

BEST SPLIT 800 BLACK BHC84751BA [13/56] English

English

! The appliance must be installed by a qualified person in

compliance with the instructions provided.

Wear gloves when carrying out installation and

maintenance operations.

If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

Warning: Failure to install the screws or fixing device in

accordance with these instructions may result in electrical

hazards.

The hood can look different to that illustrated in the

drawings in this booklet. The instructions for use,

maintenance and installation, however, remain the same.

AIR VENT

(for ducting versions)

! Prepare the hole and the air vent duct (150 mm

diameter).

! Use a duct of the minimum indispensible length.

! Use a duct with as few elbows as possible (maximum

elbow angle: 90°).

! Avoid drastic changes in the duct cross-section.

! Use a duct with an as smooth as possible inside.

! The duct must be made of certified material.

! Do not connect the hood to smoke exhaust ducts for the

products of combustion (boilers, fireplaces, stoves, etc).

! For the air vents comply with the provisions laid down by

the competent authorities.

In addition, the air must not be evacuated through a hole

in the wall unless specifically intended for this purpose.

! Fit air intakes in the room to prevent the hood from

creating a negative pressure in the room (which must

not exceed 0.04 mbar); if the hood is used at the same

time as non-electrical equipment (gas-, oil- and

charcoal-fired stoves, etc.) the exhaust gas may be

sucked in by the heat source.

FILTERING OR DUCTING VERSION ?

The hood may be in filtering or in ducting version. Decide

from the outset which type is to be installed.

For better efficiency, we recommend installing the hood in

the ducting version (if possible).

Ducting version

The hood purifies the air and evacuates it to the outside

through an exhaust duct (diameter 150 mm).

Version with an outside motor

In the version with an outside motor, a vacuum suction unit

must be connected; this exhaust will operate separately,

conveying the exhaust air through the unit. Only use

vacuum unitssuggested in the original catalogue.

Filtering version

The hood purifies the air and recycles the clean air back

into the room.

Only for hoods equipped with electronic control:

The 4th speed (intensive) is automatically lowered to 3rd

speed after 5 minutes of operation to optimise energy

consumption.

- If the hood is left on (lights and/or motor), after 10 hours in

the absence of commands from the user, it will

automatically switch to OFF condition with all services

switched off.

- The Buzzer emits a “beep” each time that a command is

set from the keyboard or remote control (optional).

- In the event of interruption of power during the hood, if you

restore the hood in the OFF state, then the engine must be

reactivate manually.

CONTROLS

Controls of Fig. 20

A) Turns the LIGHTS off.

B) Turns the LIGHTS on.

C) Decreases speed down to minimum speed. If pressed

for 2” the motor is turned off.

D) Activates the motor (calling the last speed used) and

increases the speed until reaching maximum.

E) FILTER ALARM/TIMER RESET: when pressing the key

during display of the filter alarm (motor off) its reset the

hour counter. When pressing the key when the motor is

running, the TIMER is activated and the hood will

automatically be switched off after 5 minutes.

L1) The 4 green LEDs indicate the running speed.

L2) When the LED is red (motor off) it indicates the FILTER

ALARM. When the LED is green (flashing) it indicates that

the TIMER has been activated with the key E.

FILTER ALARM:

After 30h of operation, the LED L2 turns RED. It indicates

that the grease filters need to be cleaned.

After 120h of operation, the LED L2 turns RED and flashes;

It indicates that the grease filters need to be cleaned and

the charcoal filters replaced.

After cleaning the grease filters (and/or replacing the

charcoal filters), restart the hour counter (RESET) by

pressing the key E during display of the filter alarm.

Controls of Fig. 21

Key A: light switch.

Key B: first speed motor ON/OFF switch.

Key C: second speed switch.

Key D: third speed switch.

Controls of Fig. 22

P1: It turns on an off the light.

P2: It starts the engine setting it to the first speed (the icon

is highlighted). Other speed icons remain inactive.

P3: It starts the engine setting it to the second speed (the

icon is highlighted). Other speed icons remain inactive.

P4: It starts the engine setting it to the third speed (the icon

is highlighted). Other speed icons remain inactive.

P5: It starts the engine setting it to the fourth speed (the

icon is blinking). Other speed icons remain inactive. The

maximum speed is set to be maintained for maximum 5

minutes, after this time the speed will be automatically

adjusted to the third speed.

P6: It starts the timer (the icon is highlighted). By running

Содержание

Похожие устройства

English The appliance must be installed by a qualified person in compliance with the instructions provided A Wear gloves when carrying out installation and maintenance operations If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Warning Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards The hood can look different to that illustrated in the drawings in this booklet The instructions for use maintenance and installation however remain the same The hood purifies the air and recycles the clean air back into the room Only for hoods equipped with electronic control The 4th speed intensive is automatically lowered to 3rd speed after 5 minutes of operation to optimise energy consumption If the hood is left on lights and or motor after 10 hours in the absence of commands from the user it will automatically switch to OFF condition with all services switched off The Buzzer emits a beep each time that a command is set from the keyboard or remote control optional In the event of interruption of power during the hood if you restore the hood in the OFF state then the engine must be reactivate manually CONTROLS AIR VENT for ducting versions Prepare the hole and the air vent duct 150 mm diameter Use a duct of the minimum indispensible length Use a duct with as few elbows as possible maximum elbow angle 90 Avoid drastic changes in the duct cross section Use a duct with an as smooth as possible inside The duct must be made of certified material Do not connect the hood to smoke exhaust ducts for the products of combustion boilers fireplaces stoves etc For the air vents comply with the provisions laid down by the competent authorities In addition the air must not be evacuated through a hole in the wall unless specifically intended for this purpose Fit air intakes in the room to prevent the hood from creating a negative pressure in the room which must not exceed 0 04 mbar if the hood is used at the same time as non electrical equipment gas oil and charcoal fired stoves etc the exhaust gas may be sucked in by the heat source FILTERING OR DUCTING VERSION The hood may be in filtering or in ducting version Decide from the outset which type is to be installed For better efficiency we recommend installing the hood in the ducting version if possible Ductingversion The hood purifies the air and evacuates it to the outside through an exhaust duct diameter 150 mm Version with an outside motor In the version with an outside motor a vacuum suction unit must be connected this exhaust will operate separately conveying the exhaust air through the unit Only use vacuum unitssuggested in the original catalogue Controlsof Fig 20 A Turns the LIGHTS off B Turns the LIGHTS on C Decreases speed down to minimum speed If pressed for 2 the motor is turned off D Activates the motor calling the last speed used and increases the speed until reaching maximum E FILTER ALARM TIMER RESET when pressing the key during display of the filter alarm motor off its reset the hour counter When pressing the key when the motor is running the TIMER is activated and the hood will automatically be switched off after 5 minutes L1 The 4 green LEDs indicate the running speed L2 When the LED is red motor off it indicates the FILTER ALARM When the LED is green flashing it indicates that the TIMER has been activated with the key E FILTERALARM After 30h of operation the LED L2 turns RED It indicates that the grease filters need to be cleaned After 120h of operation the LED L2 turns RED and flashes It indicates that the grease filters need to be cleaned and the charcoal filters replaced After cleaning the grease filters and or replacing the charcoal filters restart the hour counter RESET by pressing the key E during display of the filter alarm Controlsof Fig 21 Kev A light switch Key B first speed motor ON OFF switch Kev C second speed switch Key D third speed switch Controlsof Fig 22 P1 It turns on an off the light P2 It starts the engine setting it to the first speed the icon is highlighted Other speed icons remain inactive P3 It starts the engine setting it to the second speed the icon is highlighted Other speed icons remain inactive P4 It starts the engine setting it to the third speed the icon is highlighted Other speed icons remain inactive P5 It starts the engine setting it to the fourth speed the icon is blinking Other speed icons remain inactive The maximum speed is set to be maintained for maximum 5 minutes after this time the speed will be automatically adjusted to the third speed P6 It starts the timer the icon is highlighted By running

Скачать