BLACK & DECKER BD40K27A-RU ION [9/28] Accessories
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

BLACK & DECKER BD40K27A-RU ION [9/28] Accessories

BLACK & DECKER BD40K27A-RU ION [9/28] Accessories
99
ENGLISH
the optimum size of the clearance hole, refer to the table
below.
Screw size
Pilot hole Ø
(softwood)
Pilot hole Ø
(hardwood)
Clearance
hole
No. 6 (3,5 mm) 2,0 mm 2,5 mm 4 mm
No. 8 (4 mm) 3,2 mm 3,5 mm 5,0 mm
MAINTENANCE
Your BLACK+DECKER tool has been designed to operate
over along period of time with aminimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning. Your charger does not r
equire any maintenance apart from regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from
the power source before making adjustments or
removing / installing devices or accessories. An
accidental start could cause injuries.
IMPORTANT! To ensure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(other than those listed in this manual) should be
performed by authorized service centers or other
qualified organizations, always using identical
replacement parts. Unit contains no user service able
parts inside.
CLEANING
WARNING: Blow dirt and dust from all ventilation
ducts with dry air, at least once aweek. To reduce
the risk of injury, always use ANSI z87.1 Approved eye
protection when performing this task.
WARNING: Never use solvents or other abrasive
chemicals to clean non-metallic parts of the tool.
These chemicals can weaken the plastic materials
used in these parts. Use acloth dampened only
with water and neutral soap. Never allow liquid to
penetrate inside the tool or immerse any of the parts
in aliquid.
ACCESSORIES
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
WARNING! The use of any accessory not
recommended for use with this tool could be
hazardous.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be disposed
of with normal household waste. Should you find
one day that your BLACK+DECKER product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Setting the Torque (E-clutch)
The torque selection button lets you choose between
5 different torque positions. . The tool stops automatically as
soon as the set torque is reached. There are 5 lights above
the torque selection button indicating the amount of torque
being applied, from position 1 (one light on, for lowest
torque) to position 5 (five lights on, for highest torque).
Press the button one time for position one (one light on).
Press two times for position two (two lights on). Press three
times for position three (three lights on). Press four times for
position four (four lights on). Press five times for position 5
(five lights on).
• Position 1: Lower torque for driving screws with small
diameter or into soft materials.
• Position 5: Higher torque for driving screws with large
diameter or into hard materials.
Starting and Stopping
• To start, push the tool against the screw and maintain
the pressure.
• To stop, stop pushing the tool against the screw.
Wire Stripper
1. Feed wire into guide notch
2. Press the wire stripper tab and twist the tool slightly
3. Pull the tool towards the end of wire
NOTE: It is important to match the size of wire to the correct
notch in the stripper. If the notch is too large, the wire will
not get stripped. If the notch is too small, there is arisk of
damaging the wire.
If awire accidentally gets damaged, it is best to cut the
damaged part of the wire off and try again.
Changing the Accessory
Slide the rotational direction switch into the middle position.
This locks the spindle in place, Insert the screwdriver bit
directly into the tool holder
Hints for Optimum Use
• Let the tool work at its own pace. Do not overload.
• Always use the correct type and size of screwdriver bit.
• If screws are difficult to tighten, try applying asmall
amount of washing liquid or soap as alubricant.
• Use the auto spindle lock to loosen very tight screws or to
firmly tighten screws.
• Always hold the tool and screwdriver bit in astraight line
with the screw.
• When screwing in wood, it is recommended to drill
apilot hole with adepth equal to the length of the screw.
Apilot hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
• When screwing in hardwood, also drill aclearance hole
with adepth equal to half the length of the screw. For

Содержание

Похожие устройства

Скачать