Festool TSC 55 Li REB-Basic (201395) без акк. и з.у [20/123] Warning
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Festool TSC 55 Li REB-Basic (201395) без акк. и з.у [20/123] Warning

Festool TSC 55 Li REB-Basic (201395) без акк. и з.у [20/123] Warning
20
TSC 55 REB
GB
8 Working with the machine
Please observe all mentioned safety infor-
mations and the following rules when work-
ing:
– Only guide the power tool towards the workpiece
when it is switched on.
– Check the installation fixture prior to use and do
not use the machine if the fixture does not func-
tion correctly.
– After dropping check the power tool and the saw
blade for damage. Have the damaged parts re-
paired before use. Damaged machines may lead
to injuries and cause the machine to be unsafe.
– Always secure the workpiece in such a manner
that it cannot move while being processed.
– Always hold the machine with two hands at the
handles
[1-1]
when performing work. This re-
duces the risk of injury and is a prerequisite for
precise work.
– Always push the machine forwards
[10-2]
, never
draw the machine towards yourself.
– Adapt the fast-feed speed to prevent the cutters
on the saw blade from overheating and prevent
plastic materials from melting during cutting.
– Make sure that all rotary knobs
[1-2]
are tight-
ened before starting work.
– Check that the saw blade is seated securely.
– Static charge may occur when sawing (e.g. MDF).
For work that generates dust, wear a dust
mask.
8.1 Switch on/off
Slide the switch-on lock
[1-5]
upwards and press
the on/off switch
[1-6]
(press = ON / release = OFF).
Pressing the switch-on lock unlocks the
plunging mechanism. The saw unit can then
be moved downwards. This causes the saw
blade to emerge from the protective cover.
8.2Acoustic warning signal
Acoustic warning signals sound and the machine
switches off in the following operating states:
Change the battery
Reduce the machine load
8.3 Sawing along the scribe mark
The cutting indicator
[8-2]
displays the cutting line
for 0° and 45° cuts (without guide rail).
8.4 Cutting sections
Place the machine with the front part of the saw ta-
ble on the workpiece, switch the machine on, press
it down to the preset cutting depth and push it for-
ward in the cutting direction.
8.5 Sawing cut outs (plunge cuts)
In order to avoid kickbacks, the following in-
structions must be observed without fail
when plunge cutting:
– Always place the machine with the rear edge of
the saw table against a fixed stop.
– When working with the guide rail, place the ma-
chine against the kickback stop FS-RSP (acces-
sory)
[10-4]
clamped to the guide rail.
Procedure
Position the machine on the workpiece and
push up against a stop (kickback stop).
Switch on the machine.
Push down the machine slowly to the preset
cutting depth and then push forwards in the cut-
ting direction.
The markings
[8-1]
indicate the absolute front and
the absolute rear cutting points of the saw blade
(dia. 160 mm) when using the saw at maximum cut-
ting depth with the guide rail.
8.6 Gypsum and cement-bound fibreboards
Due to the high volume of dust, it is recommended
to use the cover ABSA-TS55 (accessories) which
can be mounted at the side at the protective cover
and a Festool mobile dust extractor.
9 Service and maintenance
Customer service and repair
only
through manufacturer or service
workshops: Please find the nearest
address at: www.festool.com/service
Only use original Festool spare parts!
Order No. at: www.festool.com/service
Battery low or machine overloaded:
peep
WARNING
Risk of injury, electric shock
Always disconnect the battery pack from the
machine before any cleaning or maintenance!
All maintenance and repair work which requires
the motor housing to be opened, must only be
carried out by an authorised service workshop.
EKAT
1
2
3
5
4

Содержание

Похожие устройства

Скачать