![Janome Jem Gold 2 [8/25] Отключение транспортера ткани](/img/pdf.png)
Janome Jem Gold 2 [8/25] Отключение транспортера ткани
![Janome Jem Gold 2 [8/25] Отключение транспортера ткани](/views2/1964262/page8/bg8.png)
7
Выбор строчек
Поднимите иглу, установите нужную строчку
вращая ручку выбора строчек.
Примечание: Не поворачивайте ручку выбора
строчек, если игла находится в ткани. Иначе
игла может погнуться или сломаться.
1 Окошко выбора строчки
2 Регулятор выбора строчек
Рычаг подъема прижимной лапки
Рычаг подъема поднимает и опускает
прижимную лапку.
Рычаг дает возможность поднять лапку выше
обычного положения на 0.6 см, чтобы заменить
лапку или подложить тяжелую ткань.
1 Обычное поднятое положение
2 Верхнее положение
3 Рычаг подъема лапки
Прижимная лапка
Как установить и снять прижимную лапку
1 Поднимите прижимную лапку. Нажмите на
рычаг позади держателя лапки.
Прижимная лапка отскочит.
1 Рычаг
2 Расположите лапку, чтобы перекладина
лапки находилась под выемкой держателя.
Опустите лапку и пристегните ее.
2 Выемка
3 Перекладина
Реверс
При удержании кнопки реверса машина шьет
в обратную сторону.
Отключение транспортера ткани
Рычаг транспортера ткани находится под
свободным рукавом позади машины.
Передвиньте рычаг отключения транспортера
ткани вправо 1 и отключите его.
Чтобы поднять зубчатую рейку, передвиньте
рычаг влево 2 и поверните на себя маховое
колесо. При обычном шитье транспортер ткани
должен быть поднят.
7
q
w
w
q
w
q
e
q
e
w
z
x
Pattern Selection
Raise the needle, turn the pattern selector dial to select
the desired pattern.
Note: Do not turn the pattern selector dial while the
needle is in the fabric, otherwise the needle may
bend or break.
q
Pattern indication window
w Pattern selector dial
Presser Foot Lifter
The presser foot lifter raises and lowers the presser foot.
You can raise it about 0.6 cm (1/4˝) higher than the
normal up position for easy removal of the presser foot or
to help you place heavy fabric under the foot.
q
Normal up position
w High position
e Presser foot lifter
To Attach and Remove the Presser Foot
z Raise the presser foot. Press the lever on the back of
the foot holder.
The presser foot will drop off.
q
Lever
x Place the selected presser foot so the pin on the
foot lies just under the groove of the foot holder.
Lower the presser bar to lock the foot in place.
w
Groove
e Pin
Reverse Stitch Lever
The machine will sew in reverse while the reverse stitch
lever is depressed.
How to Drop the Feed Dog
The drop feed dog lever is located underneath the free
arm bed on the back side of the machine.
To drop the feed dog, slide the drop feed dog lever to the
right
q.
To raise the feed dog, slide the drop feed dog lever to the
left w, and turn the handwheel toward you.
The feed dog must be up for normal sewing.
q
w
q
w
7
q
w
w
q
w
q
e
q
e
w
z
x
Pattern Selection
Raise the needle, turn the pattern selector dial to select
the desired pattern.
Note: Do not turn the pattern selector dial while the
needle is in the fabric, otherwise the needle may
bend or break.
q
Pattern indication window
w Pattern selector dial
Presser Foot Lifter
The presser foot lifter raises and lowers the presser foot.
You can raise it about 0.6 cm (1/4˝) higher than the
normal up position for easy removal of the presser foot or
to help you place heavy fabric under the foot.
q
Normal up position
w High position
e Presser foot lifter
To Attach and Remove the Presser Foot
z Raise the presser foot. Press the lever on the back of
the foot holder.
The presser foot will drop off.
q
Lever
x Place the selected presser foot so the pin on the
foot lies just under the groove of the foot holder.
Lower the presser bar to lock the foot in place.
w
Groove
e Pin
Reverse Stitch Lever
The machine will sew in reverse while the reverse stitch
lever is depressed.
How to Drop the Feed Dog
The drop feed dog lever is located underneath the free
arm bed on the back side of the machine.
To drop the feed dog, slide the drop feed dog lever to the
right
q.
To raise the feed dog, slide the drop feed dog lever to the
left w, and turn the handwheel toward you.
The feed dog must be up for normal sewing.
q
w
q
w
Содержание
- Важные инструкции по безопасности 2
- Внимание 2
- Дизайн и спецификация машины могут быть изменены 2
- Опасно 2
- Сохраняйте эти инструкции 2
- Names of parts 3
- Section i name of parts 3
- V дополнительные строчки 3
- Наименование частей 3
- Основные швейные техники 3
- Подготовка к шитью 3
- Раздел 3
- Раздел v декоративные строчки 3
- Содержание 3
- Уход за машиной 3
- Section i name of parts 4
- Наименование частей 4
- Раздел 4
- Connecting machine to power supply 5
- Controlling sewing speed 5
- Section ii getting ready to sew 5
- Standard accessories and storage place 5
- Стандартные аксессуары 5
- Connecting machine to power supply 6
- Controlling sewing speed 6
- Section ii getting ready to sew 6
- Контроль скорости шитья 6
- Подготовка к шитью 6
- Подключение питания к машине 6
- Раздел 6
- Changing needles 7
- How to drop the feed dog 7
- Note do not turn the pattern selector dial while the needle is in the fabric otherwise the needle may bend or break 7
- Pattern selection 7
- Place the selected presser foot so the pin on the foot lies just under the groove of the foot holder lower the presser bar to lock the foot in place 7
- Presser foot lifter 7
- Raise the needle turn the pattern selector dial to select the desired pattern 7
- Raise the presser foot press the lever on the back of the foot holder the presser foot will drop off 7
- Reverse stitch lever 7
- Selecting needle and thread 7
- The drop feed dog lever is located underneath the free arm bed on the back side of the machine 7
- The machine will sew in reverse while the reverse stitch lever is depressed 7
- The presser foot lifter raises and lowers the presser foot you can raise it about 0 cm 1 4 higher than the normal up position for easy removal of the presser foot or to help you place heavy fabric under the foot 7
- To attach and remove the presser foot 7
- To drop the feed dog slide the drop feed dog lever to the right q to raise the feed dog slide the drop feed dog lever to the left w and turn the handwheel toward you the feed dog must be up for normal sewing 7
- Выбор игл и ниток 7
- Смена игл 7
- How to drop the feed dog 8
- Pattern selection 8
- Presser foot lifter 8
- Reverse stitch lever 8
- To attach and remove the presser foot 8
- Выбор строчек 8
- Отключение транспортера ткани 8
- Прижимная лапка 8
- Реверс 8
- Рычаг подъема прижимной лапки 8
- For small spool 9
- Gently slide the hook cover plate release button q to the right and remove the cover plate w lift out the bobbin e 9
- Place the spool of thread on the spool pin with the thread coming off the spool as illustrated press the large spool holder q firmly against the spool of thread 9
- Preparation of the bobbin thread 9
- Removing the bobbin 9
- Set the spool 9
- Подготовка шпульной нити 9
- Attach the hook cover plate 11
- Check the threading by referring to the chart 11
- Continue to draw the thread lightly until the thread slips into notch b 11
- Guide the thread into the notch a 11
- In the bobbin holder 11
- Inserting the bobbin 11
- On the front side of the bobbin holder draw the thread to the left sliding it between the tension spring blades 11
- Place the bobbin 11
- Pull out about 15 cm 6 of thread 11
- Shown on the hook cover plat 11
- Threading the machine 11
- With the thread running off as illustrated 11
- Draw the thread down and slide the thread behind the needle bar thread guide t from the left 12
- Raise the presser foot with the presser foot lifter q lead the thread from the spool and pass it through the thread guide w then draw it down along the right slot 12
- Raise the take up lever to its highest position by turning the handwheel towards you firmly draw the thread from right to left over the take up lever r and down into the take up lever eye 12
- See page 12 12
- Then down around the thread guide plate e 12
- Threading the machine 12
- To set the needle thread 12
- Use the needle threader to thread the needle 12
- Заправка нити в машину 12
- Bring the bobbin thread up by pulling the needle thread as illustrated 14
- Drawing up the bobbin thread 14
- Pull 10 to 15 cm 4 to 6 of both threads back and under the presser foot 14
- Raise the presser foot and hold the needle thread lightly with your left hand 14
- Turn the handwheel slowly towards you one complete turn 14
- Section iii basic sewing 15
- Triple straight stitch 15
- Основные швейные техники 15
- Прямая строчка 15
- Раздел 15
- Triple straight stitch 16
- Прямой тройной стежок 16
- Balancing needle thread tension 17
- Choose the correct tension 17
- For straight stitch the ideal straight stitch will have threads locked between the two layers of the fabric as illustrated magnified to show detail if you look at the top and bottom of the seam you will notice that there are no gaps each stitch is smooth and even turn the dial to alter the needle thread tension the higher the number the tighter the tension 17
- Overcasting 17
- Results depend on stiffness and thickness of the fabric number of fabric layers type of stitch 17
- Section iv utility stitches 17
- Tension is too loose 17
- Tension is too tight 17
- The bobbin thread shows through on the right side of the fabric and it feels bumpy 17
- The needle thread shows through on the wrong side of the fabric and it feels bumpy 17
- Tricot stitch 17
- Turn the thread tension dial downwards to a larger number to tighten the needle thread tension 17
- Turn the thread tension dial upwards to a smaller number to loosen the needle thread tension 17
- Zigzag stitching 17
- Баланс натяжения верхней нити 17
- Section iv utility stitches 18
- V дополнительные строчки 18
- Зигзаг 18
- Обработка края 18
- Раздел 18
- Трикотажный стежок 18
- Blind stitch hemming 19
- Section v decorative stitching 19
- Shell tuck 19
- Раздел v декоративные строчки 19
- Buttonhole 20
- X c v b 20
- Изготовление петли 20
- Caution 21
- Q w e embroidery 21
- Section vi care of your machine 21
- Вышивка 21
- Caution 22
- Section vi care of your machine 22
- Меры предосторожности 22
- Раздел 22
- Уход за машиной 22
- Caution wait for the light bulb to cool down before touching it 23
- Insert the bobbin holder so that the knob fits next to the stopper in the race insert the bobbin 23
- Loosen the screw and remove the face plate 23
- Note when replacing the bulb unplug the machine 23
- Replace the needle plate inserting the two needle plate guide pins into the holes in the needle plate tighten the screw firmly with the screwdriver 23
- Replacing the bobbin holder 23
- Replacing the light bulb 23
- The sewing light is located behind the face plate 23
- To remove push and turn counterclockwise to replace push and turn clockwise 23
- To remove turn the bulb counterclockwise to replace turn the bulb clockwise 23
- Вероятная причина 24
- Неисправности машины 24
- Неисправность 24
- Примечание 24
Похожие устройства
- Janome Jem Gold 660 Руководство по эксплуатации
- Janome JF1012 Руководство по эксплуатации
- Janome JF1014 Руководство по эксплуатации
- Janome JF1018S Руководство по эксплуатации
- Janome JK 203 Руководство по эксплуатации
- Janome JK 213 Руководство по эксплуатации
- Janome JK 217 Руководство по эксплуатации
- Janome JL-23 Руководство по эксплуатации
- Janome JR 1204 Руководство по эксплуатации
- Janome Juno 2206 Руководство по эксплуатации
- Janome MC 200E Руководство по эксплуатации
- Janome Memory Craft 11000 Руководство по эксплуатации
- Janome Memory Craft 12000 Руководство по эксплуатации
- Janome Memory Craft 3500 Руководство по эксплуатации
- Janome Memory Craft 4800 Руководство по эксплуатации
- Janome Memory Craft 4900 QC Руководство по эксплуатации
- Janome Memory Craft 7700 QCP Руководство по эксплуатации
- Janome Memory Craft 9400 QCP Руководство по эксплуатации
- Janome ML 77 Руководство по эксплуатации
- Janome MV 513 Руководство по эксплуатации