![ADJ 46HP LED polish [3/10] Pin xlr dmx connectors](/img/pdf.png)
ADJ 46HP LED polish [3/10] Pin xlr dmx connectors
![ADJ 46HP LED polish [3/10] Pin xlr dmx connectors](/views2/1990721/page3/bg3.png)
Power Supply: Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ
46HP LED. The American DJ 46HP LED is a 100v ~ 220v unit. Because
of voltage setup of the unit you do not have to worry about wall output
voltage. This unit is compatiable with all wall outputs.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav-
els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-
minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli-
ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The 46HP LED can be controlled via DMX-512 protocol. The 46HP LED
has 6 DMX modes, please see page 9 for the different modes. The DMX
address is set on the back panel of the 46HP LED.
Your unit and your DMX controller require a stan-
dard 3-pin XLR connector for data input and data
output (Figure 1). We recommend Accu-Cable
DMX cables. If you are making your own cables,
be sure to use standard 110-120 Ohm shielded
cable (This cable may be purchased at almost all
pro lighting stores). Your cables should be made
with a male and female XLR connector on either
end of the cable. Also remember that DMX cable
must be daisy chained and cannot be split.
©American DJ® - www.Americandj.com - 46HP LED User Manual Page 5
46HP LED Set Up
©American DJ® - www.Americandj.com - 46HP LED User Manual Page 6
Figure 1
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
46HP LED Set Up
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 2
Figure 3
1 Ground
1 Ground
XLR Male Socket
XLR Pin Conguration
3 Hot
2 Cold
2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 4
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
Содержание
- Caution 1
- Customer support 1
- Introduction 1
- Unpacking 1
- User instructions 1
- Warning 1
- Data cable dmx cable requirements for dmx operation 3
- Dmx 512 3
- Notice 3
- Ower supply 3
- Pin xlr dmx connectors 3
- Special note line termination 3
- Auto mode 4
- Auto mode speed adjustment 4
- Dmx mode 4
- Hp led operating instructions 4
- Led display on off 4
- Macro mode 4
- Master slave operation 4
- Operating modes 4
- Rgb mode 4
- Sound active mode 4
- To set the display press the mode button until 0001 is displayed the display will now stay on at all times 0001 lcd display on at all times 0002 lcd display shuts off after 10 seconds 4
- To set the led display to turn off after 10 seconds press the mode button until 0001 is displayed press the up button to display 0002 now the display will disappear after 10s press any button to turn the display on again be advised though that the display will turn off automatically after 10 seconds 4
- Channel 1 2 and 3 will not work when channel 4 is being used 7
- Hannel 7
- Hp led 7 channel dmx values functions 7
- Hp led photometrics 7
- Red 1 255 0 100 2 green 1 255 0 100 3 blue 1 255 0 100 4 1 255 color macros see 1 channel dmx mode for colors 5 0 15 nothing 16 255 strobing speed control slow fast 6 mode 0 127 color adjustment 128 159 color mixing 160 191 3 color change 192 223 7 color change 224 255 sound active 7 master dimmer 1 255 0 100 7
- Unction 7
- When using channel 6 channel 5 will control the speed of the color changing 7
- Always be sure to dry all parts completely before plugging the unit back in 8
- American d 8
- And outputs are connected and outputs are connected 8
- Check that the dmx cables are connected properly and are wired correctly pin 3 is hot on some other dmx devices 8
- Clean the external optics with glass cleaner and a soft cloth every 20 days 8
- Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew 8
- Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize light output 8
- Hp led cleaning 8
- Hp led fuse replacement 8
- Hp led trouble shooting 8
- Hp led warranty 8
- Listed below are a few common problems the user may encounter with solutions 8
- Locate and remove the unit s power cord once the cord has been removed located the fuse holder located inside the power socket insert a flat head screw driver into the power socket and gently pry out the fuse holder remove the bad fuse and replace with a new one the fuse holder also has a holder for a spare fuse 8
- Pin 2 may be hot also check that all cables are connected pin 2 may be hot also check that all cables are connected 8
- Quiet or high pitched sounds will not activate the unit 2 make sure that you are in sound active mode 8
- To the right connectors it does matter which way the inputs to the right connectors it does matter which way the inputs 8
- Unit does not respond to sound 8
- Unit not responding to dmx 8
- Use normal glass cleaner and a soft cloth to wipe down the outside casing 8
- Www americandj com 46hp led user manual page 15 8
- Www americandj com 46hp led user manual page 16 8
- American d 9
- Hp led notes 9
- Www americandj com 46hp led user manual page 17 9
- Www americandj com 46hp led user manual page 18 9
- Model 46hp led 10
Похожие устройства
- Sennheiser RS 110-8-II Руководство по эксплуатации
- Yamaha NS-F51 Руководство по эксплуатации
- Sennheiser M2 IEBT SW Руководство по эксплуатации
- Sennheiser M2 IEBT Руководство по эксплуатации
- Sennheiser G4ME ZERO (506064) Руководство по эксплуатации
- Marshall Stockwell Руководство по эксплуатации
- Casio Privia PX-870BK Руководство по эксплуатации
- Casio Privia PX-770WE Руководство по эксплуатации
- Casio Privia PX-770BN Руководство по эксплуатации
- Sennheiser M2 IEG Руководство по эксплуатации
- Casio CDP-235RBK Руководство по эксплуатации
- Casio AP-270BK Руководство по эксплуатации
- Yamaha YST-FSW 050 Руководство по эксплуатации
- Yamaha NS-P60 (ANSP60C2) Руководство по эксплуатации
- Yamaha NS-P150 3.0 (ANSP150BL) Руководство по эксплуатации
- Yamaha NS-P60 (ANSP60BID) Руководство по эксплуатации
- Yamaha NS-BP111 Piano (ANSBP111PIANOB) Руководство по эксплуатации
- Yamaha NS-BP111 (ANSBP111PIANOW) Руководство по эксплуатации
- Yamaha NS 333 Руководство по эксплуатации
- Yamaha CD-N301 Руководство по эксплуатации