![ADJ Royal 3D Руководство по эксплуатации онлайн [2/12] 776834](/img/pdf.png)
ADJ Royal 3D Руководство по эксплуатации онлайн [2/12] 776834
![ADJ Royal 3D Руководство по эксплуатации онлайн [2/12] 776834](/views2/2008549/page2/bg2.png)
©American DJ® - www.americandj.com - Royal 3D Instruction Manual Page 4©American DJ® - www.americandj.com - Royal 3D Instruction Manual Page 3
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and mainte-
nance of this unit. Please keep this manual with the unit, for future
reference.
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Royal 3D General Instructions Royal 3D Safety Precautions
Safety Issues: This unit may “pop” the fuse if the maximum allotted
load of 2 amps is reached.
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short. Do not attempt to oper-
ate this unit if the power cord has been frayed or broken.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power cords should be routed so they are not likely to be walked
on, pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 20 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a
marked change in performance.
• 30mW Green Laser & 350mW Violet Blue Laser
• 5 Channel DMX Control
• 2 Operating Modes - Sound Active & DMX Control
• Digital Display for Address and Function Setting
• UC3 Controller (Not Included)
• Run as Stand Alone unit or in a Master-Slave Conguration
• Power Cord Daisy Chain up to 16 units max. See page 16
Royal 3D Features
Royal 3D Warranty Registration
The Royal 3D carries a 90 day limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. If the unit is under
warranty you must provide a copy of your proof of purchase invoice.
Please contact American DJ® customer support for a R.A. number.
!
!
LASER RADIATION AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength: 405, 532nm
Class IIIa laser product
This device complies with 21 CFR chapter I,
Subchapter J, or CFR 1040.10 and 1040.11
Содержание
- Caution 1
- Customer support 1
- Introduction 1
- Unpacking 1
- User instructions 1
- Warning 1
- Operation instructions and laser safety 3
- Stop and read all laser safety data 3
- Dmx 512 4
- Power supply 4
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior 5
- Conductor 5 pin xlr male in 3 pin xlr female out 5
- Data compliment signal 5
- Data true signal 5
- Dmx cable must be daisy chained and cannot be split 5
- Ground shield 5
- Not used 5
- Notice 5
- Pin 4 do not use 5
- Pin 5 do not use 5
- Pin xlr dmx connectors 5
- Pin xlr to 5 pin xlr conversion 5
- Royal 3d set up 5
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion 5
- Special note line termination 5
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior 5
- Dmx address setting via control board 6
- In this mode you can run in sound active mode 6
- System menu when confirming your setting press enter and then hold menu for at least 2 3 seconds or you can wait 1 minute for automatic setup to exit without making any adjustments press the menu button 6
- This will let you set unit as a slave in a master slave configuration 6
- Sound sensitivity control 7
- This function will flip the led display 180º 7
- This function will run a self test program 7
- This will control blackout 7
- This will display the software version 7
- Use this function to reset the unit 7
- With this function the led display will turn off after 2 minutes 7
- With this function you can display the running time of the unit 7
- Master slave configuration 8
- Operating modes the royal 3d has two different operating modes 8
- Sound active mode stand alone or master slave 8
- Universal dmx control 8
- Always be sure to dry all parts completely before plugging the unit back in 10
- American d 10
- Be sure the fuse holder is completely and properly seated 4 be sure the unit is not in blackout mode unit does not respond to sound 10
- Be sure you have turned on the unit 2 be sure the external fuse has not blown the fuse is located on the rear panel of the unit 10
- Clean the external optics with glass cleaner and a soft cloth every 20 days 10
- Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew in heavy use we recom mend cleaning on a monthly basis periodic cleaning will ensure lon gevity and crisp beam output 10
- Due to fog residue smoke and dust cleaning the internal and external lenses should be carried out periodically to optimize light output 1 use normal glass cleaner and a soft cloth to wipe down the out side casing 10
- Fixture cleaning 10
- Locate and remove the unit s power cord once the cord has been removed located the fuse holder located inside the power socket insert a flat head screw driver into the power socket and gently pry out the fuse holder remove the bad fuse and replace with a new one the fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse 10
- Low frequencies bass should cause the unit to react to sound tapping on the microphone quiet or high pitched sounds may 10
- No laser output from the unit 10
- Not activate the unit not activate the unit 10
- Royal 3d cleaning 10
- Royal 3d fuse replacement 10
- Royal 3d trouble shooting 10
- Royal 3d warranty 10
- Trouble shooting listed below are a few common problems that you may encounter with solutions 10
- Www americandj com royal 3d instruction manual page 19 10
- Www americandj com royal 3d instruction manual page 20 10
- American dj europe 12
- American dj supply 12
- American dj world headquarters 12
- Auto sensing voltage 12
- Ew kerkrade 12
- Junostraat 2 12
- Model royal 3d 12
- Netherlands 12
- Please note 12
- S eastern ave los angeles ca 90040 usa 12
- Service adjgroup eu www americandj eu 12
- Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 12
- Tel 31 45 546 85 00 fax 31 45 546 85 99 12
- Tel 323 582 2650 fax 323 582 2610 12
- This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source 12
- Web www americandj com e mail info americandj com 12
- Www maxlight ru 12
Похожие устройства
- ADJ Revo 4 LED Руководство по эксплуатации
- ADJ Quad Phase HP Руководство по эксплуатации
- JENSEN LOUDSPEAKERS P12N (8 Ohm) Руководство по эксплуатации
- JENSEN LOUDSPEAKERS P12N (16 Ohm) Руководство по эксплуатации
- Yamaha EMX512SC Руководство по эксплуатации
- Yamaha DXS15 Руководство по эксплуатации
- Yamaha EMX2 Руководство по эксплуатации
- Yamaha DM-105 Руководство по эксплуатации
- Sennheiser RS160 Руководство по эксплуатации
- Sennheiser MM400 Руководство по эксплуатации
- Denn DEK895 Руководство по эксплуатации
- Soundmax SM-DM001 Руководство по эксплуатации
- Tannoy Eclipse Сеntre Руководство по эксплуатации
- Tannoy Eclipse Three Руководство по эксплуатации
- Taurus TF-112 Руководство по эксплуатации
- Taurus TH-Cross Руководство по эксплуатации
- Taurus TF-115 Руководство по эксплуатации
- ASHLY PE-800 + PE-DSP1 Руководство пользователя
- ASHLY ne4250.10pe Руководство пользователя
- ASHLY CLX-52S Руководство пользователя