Vitek VT-8700 [18/56] English

Vitek VT-8700 [18/56] English
18
ENGLISH
displayed on the right side of the screen), press
the «+» or «-» button to adjust the amount of
ground coffee in grams. When brewing coffee
(the «ml» symbols are displayed on the right
side of the screen), press the «+» or «-» button
to adjust the volume of brewed coffee in milli-
liters. When supplying water (the «ml» symbols
are displayed on the right side of the screen),
press the «+» or «-» button to adjust the volume
of supplied water in milliliters. Press the button
«2 cups» « » to prepare 2 cups of coffee.
To force the end of the preparing process, press
the button «Exit» « ».
Hot water supply
1. Install a suitable cup on the metal grid of the tray
(10) and adjust the height of the coffee supply
unit (8) (Fig. 6).
2. Press the button «Hot Water» « » to start the
hot water supply (Fig. 9).
3. When the volume of hot water in the cup reach-
es the desired level, press the button «Exit»
« » on the control panel to complete the
process.
Note: During preparation of coffee drinks and sup-
ply of hot water, the illumination of the coffee sup-
ply unit turns on.
Below is a table with the factory settings (by default) and possible changes of the settings for
preparing each drink:
Beverage name
Ground beans
weight, g
Ready coffee
amount, ml
Frothed milk,
sec.
Temperature,
°С
Hot water,
ml
Espresso
9-11 20-250 - 75-95 -
By default 10 40 - 90 -
Americano
9-11 20-250 - 75-95 0-250
By default 10 60 - 90 80
Hot water
- - - - -
By default - - - - 250
CLEANING/FLUSHING
1. Install a suitable cup on the metal grid of the tray
(10) and adjust the height of the coffee supply
unit (8) (Fig. 6).
2. To start the process, press the button «Flush»
« » and hold it for more than 3 seconds un-
til you hear three short sound signals (Fig. 10).
The coffee machine uses about 45 ml of water
and automatically turns off its supply after flush-
ing is completed. During flushing of the sys-
tem, the «clean» symbols will be shown on the
control panel display and the illumination of the
coffee supply unit will turn on. After the system
is flushed, the coffee machine will switch to the
standby mode.
FUNCTIONALITY
Preheating of cups
To preserve the taste and aromatic properties of
the prepared drinks, it is recommended to heat the
cups before filling them. To do this, there is a spe-
cial tray for heating cups (6) in the upper part of the
coffee machine.
Coffee grinding adjustment
To prepare a high-quality coffee drink, adjust the
degree of grinding according to the degree of
roasting of coffee beans that you use (it is recom-
mended to use medium-roasted coffee beans).
The grinding degree controller of the grinder al-
lows you to set 5 fixed degrees of grinding of coffee
beans, where 1 is the minimum degree of grinding
(fine grinding), 5 is the maximum degree of grind-
ing (coarse grinding). The grinding degree control
knob (4) is located inside the coffee bean container
(5) (Fig. 2).
Open the lid of the coffee bean container (3) and
set the control knob (4) to position 3 before the
first grinding (Fig. 2). Press the button «Espresso»
« »to start preparation (Fig. 7) and wait for the
drink to be prepared. Evaluate the quality of the
prepared drink.
If the coffee is too strong and the coffee flow from
the coffee supply unit (8) is too slow (difficult),
slightly increase the grinding degree, set the grind-
ing degree control knob (4) to position 4. Press the
«Espresso» button and wait for the drink to be pre-
pared.
You will be able to evaluate the result of changing
the adjustment only after making 2-3 cups of cof-
fee.
ATTENTION! During the use of the coffee ma-
chine, the adjustment of the degree of coffee
grinding must be carried out only when the coffee

Содержание

Похожие устройства